could debug processes after the commit that introduced the typo.
Security is good, but security is not always the same as turning things
off :-).
PR: kern/22711
Obtained from: brooks@one-eyed-alien.net
the encoding and using the character set [a-zA-Z0-9]. This gives a total
of 62^6 = 56800235584 possible temporary filenames for the usual default
invocation of 6 X's (compared to as few as 52 possibilities for the
previous algorithm where up to 5 characters were wasted by the PID).
Update some apparently bitrotten comments to reflect reality.
Audited by: eivind, freebsd-audit
Reviewed by: freebsd-current (a while ago)
Originally submitted by: Peter Jeremy <Peter.Jeremy@alcatel.com.au>
mainly cut-n-pasted from the i386 port, except for the method of setting
the child's stack which is the only MD part of this function.
I've tested with the example apps shipped with the linux threads source
code (ex1-ex6) and with several binary builds of Mozilla.
- No signal translation is needed. Our signals match the OSF/1 signals
- an OSF/1 sigset_t is 64 bits. Make certain to use all 64-bits of it.
We'd previously only used the lower 32 bits. This was mostly harmless
as I don't know of an OSF/1 apps which use any signals > 31. However,
the alpha Linux ABI uses the osf/1 signal routines and threaded linux
apps tyically use signals 32 and 33 to comminicate with the manager
thread, so it is important we preserve the upper 32-bits.
Reviewed by: marcel (at least in principal)
numerous error recovery buglets.
Many thanks to Tor Egge for his assistance in diagnosing problems with
the error recovery code.
aic7xxx.c:
Report missed bus free events using their own sequencer interrupt
code to avoid confusion with other "bad phase" interrupts.
Remove a delay used in debugging. This delay could only be hit
in certain, very extreme, error recovery scenarios.
Handle transceiver state changes correctly. You can now
plug an SE device into a hot-plug LVD bus without hanging
the controller.
When stepping through a critical section, panic if we step
more than a reasonable number of times.
After a bus reset, disable bus reset interupts until we either
our first attempt to (re)select another device, or another device
attemps to select us. This removes the need to busy wait in
kernel for the scsi reset line to fall yet still ensures we
see any reset events that impact the state of either our initiator
or target roles. Before this change, we had the potential of
servicing a "storm" of reset interrupts if the reset line was
held for a significant amount of time.
Indicate the current sequencer address whenever we dump the
card's state.
aic7xxx.reg:
Transceiver state change register definitions.
Add the missed bussfree sequencer interrupt code.
Re-enable the scsi reset interrupt if it has been
disabled before every attempt to (re)select a device
and when we have been selected as a target.
When being (re)selected, check to see if the selection
dissappeared just after we enabled our bus free interrupt.
If the bus has gone free again, go back to the idle loop
and wait for another selection.
Note two locations where we should change our behavior
if ATN is still raised. If ATN is raised during the
presentation of a command complete or disconnect message,
we should ignore the message and expect the target to put
us in msgout phase. We don't currently do this as it
requires some code re-arrangement so that critical sections
can be properly placed around our handling of these two
events. Otherwise, we cannot guarantee that the check of
ATN is atomic relative to our acking of the message in
byte (the kernel could assert ATN).
Only set the IDENTIFY_SEEN flag after we have settled
on the SCB for this transaction. The kernel looks at
this flag before assuming that SCB_TAG is valid. This
avoids confusion during certain types of error recovery.
Add a critical section around findSCB. We cannot allow
the kernel to remove an entry from the disconnected
list while we are traversing it. Ditto for get_free_or_disc_scb.
aic7xxx_freebsd.c:
Only assume that SCB_TAG is accurate if IDENTIFY_SEEN is
set in SEQ_FLAGS.
Fix a typo that caused us to execute some code for the
non-SCB paging case when paging SCBs. This only occurred
during error recovery.
This allows build flags to be specified for a particular program from
within the crunch.conf file, eg:
prog ppp
special ppp buildopts -DNOKLDLOAD -DNOINET6 -DNONAT -DNOATM
This adds '-DNOKLDLOAD -DNOINET6 -DNONAT -DNOATM' to make targets
related to ppp when determining which object files to build and
when calculating dependencies and building the targets.
block bitmaps before unmount() completes. They were written using
bdwrite(), so they were normally written less than 32 seconds after
unmount(), but this is too late if the media is removed or the system
is rebooted soon after unmount(). sync()ing before unmount() didn't
help, because ext2fs uses buggy private caching for these blocks --
it doesn't even bdwrite() them until they are uncached or the filesystem
is unmounted. sync()ing after unmount() didn't help, because sync()
only applies to (vnodes for) mounted filesystems.
PR: 22726
* xref sysctl
* do not mark kern.ipc.mbuf_wait up as a function argument.
* do not mix case of function argument names
* a mbuf -> an mbuf
* if -> whether
* typos
As of this patchset, the loader builds (under NetBSD/macppc), boots, interacts
and talks to BOOTP/NFS servers.
(main.c was moved from boot/ofw/libofw to boot/ofw/common but has no revision
history)
Reviewed by: obrien
This brings the loader up to the point where I can compile it under
NetBSD/macppc and have it boot, interact and talk to NFS servers.
sys/boot/ofw/libofw/main.c has been deleted (it has no revision history) and
replaced with sys/boot/ofw/common/main.c
Reviewed by: obrien
The test for failing the end guard was always triggering (and was reported as
such in compiler warnings). This is a temporary band-aid until I can work
out what's really going on.
Reviewed by: obrien
