I2C real-time clock (RTC).
The DS3231 has an integrated temperature-compensated crystal oscillator
(TXCO) and crystal.
DS3231 has a temperature sensor, an independent 32kHz output (which can be
turned on and off by the driver) and another output that can be used as
interrupt for alarms or as a second square-wave output, which frequency and
operation mode can be set by driver sysctl(8) knobs.
Differential Revision: https://reviews.freebsd.org/D1016
Reviewed by: ian, rpaulo
Tested on: Raspberry pi model B
The current GSO implementation in netback is broken and causes errors on the
guest tx path. While this is fixed disable GSO in order to have a working
netback.
Sponsored by: Citrix Systems R&D
Discussed with: gibbs
The optimization made in r239940 is valid for struct mbuf's current structure
and size in FreeBSD, but hardcodes assumptions about sizes of struct mbuf,
which are unfortunately broken if additional data is added to the beginning of
struct mbuf
X-MFC note (discussed with rwatson):
This change requires the MPKTHSIZE definition, which is only available after
head@r277203 and will not be MFCed as it breaks mbuf(9) KPI.
A direct commit to stable/10 and merges to other branches to add the necessary
definitions to work with the code as-is will be done to facilitate this MFC
PR: 194314
MFC after: 2 weeks
Approved/Reviewed by: erj, jfv
Sponsored by: EMC / Isilon Storage Division
Provide sys/dev/fdt/simplebus.h with the class declaration so that it
is possible to subclass FDT simplebus.
Differential Revision: https://reviews.freebsd.org/D1886
Reviewed by: nwhitehorn, imp
Summary:
For new eMMC chips, we must signal controller HC capability in OP_COND command.
Reviewers: imp, ian
Reviewed By: ian
Differential Revision: https://reviews.freebsd.org/D1920
With the patch applied the number of instruction events is 1% less and
number of mispredicted branch events is 5% less under multistream TCP
traffic load close to line rate.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
CDAI_FLAG_NONE advanced information CCB flag.
Support for the flag was merged to stable/10 in r279329, and the
__FreeBSD_version in stable/10 was bumped to 1001510.
Check for that version in the mps(4) and mpr(4) drivers when determining
whether to use the flag.
Sponsored by: Spectra Logic
MFC after: 3 days
dates.
- Changed all of the PCI device strings from LSI to Avago Technologies (LSI).
- Added a sysctl variable to control how StartStopUnit behavior works. User can
select to spin down disks based on if disk is SSD or HDD.
- Inquiry data is required to tell if a disk will support SSU at shutdown or
not. Due to the addition of mpssas_async, which gets Advanced Info but not
Inquiry data, the setting of supports_SSU was moved to the
mpssas_scsiio_complete function, which snoops for any Inquiry commands. And,
since disks are shutdown as a target and not a LUN, this process was
simplified by basing it on targets and not LUNs.
- Added a sysctl variable that sets the amount of time to retry after sending a
failed SATA ID command. This helps with some bad disks and large disks that
require a lot of time to spin up. Part of this change was to add a callout to
handle timeouts with the SATA ID command. The callout function is called
mpssas_ata_id_timeout(). (Fixes PR 191348)
- Changed the way resets work by allowing I/O to continue to devices that are
not currently under a reset condition. This uses devq's instead of simq's and
makes use of the MPSSAS_TARGET_INRESET flag. This change also adds a function
called mpssas_prepare_tm().
- Some changes were made to reduce code duplication when getting a SAS address
for a SATA disk.
- Fixed some formatting and whitespace.
- Bump version of mps driver to 20.00.00.00-fbsd
PR: 191348
Reviewed by: ken, scottl
Approved by: ken, scottl
MFC after: 2 weeks
It is disabled by default but users can set IFCAP_TXCSUM on the
netmap ifnet (ifconfig ncxl0 txcsum) to override netmap and force
the hardware to calculate and insert proper IP and L4 checksums in
outbound frames.
MFC after: 2 weeks
when re-enumerating a FULL speed device. Else the wrong max packet
setting might be used when trying to re-enumerate a FULL speed device.
MFC after: 3 days
Preliminary tests indicate 32 Mpps on tx, 24 Mpps on rx
with source and receiver on two different ports of the same 40G card.
Optimizations are likely possible.
The code follows closely the one for ixgbe so i do not
expect stability issues.
Hardware kindly supplied by Intel.
Reviewed by: Jack Vogel
MFC after: 1 week
To delay packets from a particular TX queue by a particular time, write a value
into the TX Pace table s.t. pace time <= TX Pace Clock Period * (2 ^ pace value)
- the TX pace clock is 1/13 of the system clock, so its period should be 104 or
52 ns depending on whether turbo mode is active.
EFX_TX_PACE_CLOCK_BASE added by me.
Submitted by: Mark Spender <mspender at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
It solves locking problem when EFSYS_MEM_ALLOC is called in
the context holding a mutex (not allowed to sleep).
E.g. on interface bring up or multicast addresses addition.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
It is one more place missed in the previous fix.
Most likely is was just memory leak on the error handling path since
typically efsys_mem_t is filled in by zeros on allocation.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Host-bus byte order translation is not requred.
Submitted by: Artem V. Andreev <Artem.Andreev at oktetlabs.ru>
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Use remaining number of DMA segment instead of maximum number in mapping
when checking space for one more TSO segment packet.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Sync endif comment with conditional.
BOOTROM and SIENA_BOOTROM are the same, but highlight that it is Siena.
Restore commented out assertion.
Sync comments with out-of-tree driver.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
