Before the common code had hard coded limits on the IDs RXQs and TXQs could
be created with which were suited for the Windows driver with VMQ, and so
would prevent queues with IDs greater than or equal to 259 (for TXQs) or 768
(for RXQs) from being created. This change allows the limits to be set in
efsys.h, so that all 1024 queues can be created during new manftest tests.
Also, the descriptor cache sizes were also hard coded to values suited to
the smaller queue counts, and so it was necessary to make them configurable
as well.
Submitted by: Mark Spender <mspender at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Caught when efx_filter_init() failed and called efx_filter_fini() in the
teardown path.
Submitted by: Andrew Lee <alee at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Previously the driver's view was the expected outcome of any
reconfiguration even if that reconfiguration failed.
Submitted by: Ben Horgan
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
We must not enable RX queues with random parameters when they are
mapped into a VF with an untrusted driver. It's probably not a good
idea to do this anyway, so take this bit out of the table test masks.
Submitted by: Ben Hutchings
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Otherwise when processing finally comes to efx_tx_qdesc_post() it could
be insufficient space between reaped and added to post pending
descriptors.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
efx_ev_mcdi() does not assert or check that all event handlers it
calls are non-null. Add assertions at the top for all required
event handlers, as some events (in the case of this bug, monitor
events) are rare.
Submitted by: Ben Hutchings
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Use nitem() to get number of array elements.
Remove unused define.
Use TAB to indent.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
TCP header is fragmented in the case of VLAN tagged IPv6 traffic without
HW VLAN tagging.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
will be used with arm64 to find which cpus to enable, and could also be
used with 32-bit arm and mips for the same purpose.
Differential Revision: https://reviews.freebsd.org/D1825
Sponsored by: The FreeBSD Foundation
This will be needed by arm64 to find the value to pass to the psci (Power
State Coordination Interface) driver, among other things, used to enable
cores.
Differential Revision: https://reviews.freebsd.org/D1824
Reviewed by: imp
Sponsored by: The FreeBSD Foundation
properly.
If there is garbage in the flags field, it can sometimes include a
set CDAI_FLAG_STORE flag, which may cause either an error or
perhaps result in overwriting the field that was intended to be
read.
sys/cam/cam_ccb.h:
Add a new flag to the XPT_DEV_ADVINFO CCB, CDAI_FLAG_NONE,
that callers can use to set the flags field when no store
is desired.
sys/cam/scsi/scsi_enc_ses.c:
In ses_setphyspath_callback(), explicitly set the
XPT_DEV_ADVINFO flags to CDAI_FLAG_NONE when fetching the
physical path information. Instead of ORing in the
CDAI_FLAG_STORE flag when storing the physical path, set
the flags field to CDAI_FLAG_STORE.
sys/cam/scsi/scsi_sa.c:
Set the XPT_DEV_ADVINFO flags field to CDAI_FLAG_NONE when
fetching extended inquiry information.
sys/cam/scsi/scsi_da.c:
When storing extended READ CAPACITY information, set the
XPT_DEV_ADVINFO flags field to CDAI_FLAG_STORE instead of
ORing it into a field that isn't initialized.
sys/dev/mpr/mpr_sas.c,
sys/dev/mps/mps_sas.c:
When fetching extended READ CAPACITY information, set the
XPT_DEV_ADVINFO flags field to CDAI_FLAG_NONE instead of
setting it to 0.
sbin/camcontrol/camcontrol.c:
When fetching a device ID, set the XPT_DEV_ADVINFO flags
field to CDAI_FLAG_NONE instead of 0.
sys/sys/param.h:
Bump __FreeBSD_version to 1100061 for the new XPT_DEV_ADVINFO
CCB flag, CDAI_FLAG_NONE.
Sponsored by: Spectra Logic
MFC after: 1 week
temporary buffer when remaining space is not enough to hold
a whole block.
- yarrow.c: add a comment that we intend to change the code and remove
memcpy's in the future. (*)
Requested by: markm (*)
Reviewed by: markm
Approved by: so (self)
Allocate the minimum or maximum response length for GET_BOARD_CFG as
appropriate. When looking up firmware subtypes by partition ID,
check the ID against the actual response length.
Merge of the patch made by Ben Hutchings in 2011.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Mainly to unify with similar member for transmit and receive queues.
It will be used in the future for resources allocation processing.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
It avoids access to m_pkthdr when TSO packet is started and also makes
tso_start_new_packet() function smaller.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
sometimes. It will power up wrong and identify itself badly:
cardbus0: <network, ethernet> at device 0.0 (no driver attached)
cardbus0: <simple comms, UART> at device 0.1 (no driver attached)
cardbus0: <old, non-VGA display device> at device 0.2 (no driver attached)
cardbus0: <old, non-VGA display device> at device 0.3 (no driver attached)
cardbus0: <old, non-VGA display device> at device 0.4 (no driver attached)
cardbus0: <old, non-VGA display device> at device 0.5 (no driver attached)
cardbus0: <old, non-VGA display device> at device 0.6 (no driver attached)
cardbus0: <old, non-VGA display device> at device 0.7 (no driver attached)
All the higher numbered functions (.2 and above) have a config space
of all 0's. This smells a bit like a special debug mode, but the
current atheros driver doesn't cope. It is unclear if this card is
just a flake, or if we're doing something wrong in the power-up
sequence.
Put a work around into the code that tests for this rather unusual
condition. If we power a CardBus device up, and the device says it is
multi-function, and any of the functions have a 0 device ID, try the
power-up sequence again.
randomdev_init_reader to change read_random over to the newly installed
adaptor was missed. This means both read_random and arc4random (seeded
from read_random) were not returning very random data. This also
effects userland arc4random as it is seeded from kernel arc4random.
The random devices are uneffected and have returned good randomness
since the change.
All keys generated with a kernel of r273872 must be regenerated with
a kernel with this patch. Keys generated may be predictable.
Remove the warning as log is too early to print anything, and it would
always get printed due to early use of arc4random...
Reviewed by: delphij, markm
Approved by: so (delphij)
Highlights:
- Multiple verbs API updates
- Support for RoCE, RDMA over ethernet
All hardware drivers depending on the common infiniband stack has been
updated aswell.
Discussed with: np @
Sponsored by: Mellanox Technologies
MFC after: 1 month
interrupt status bit. According to the UHCI controller specification
the host controller halted interrupt is non-maskable.
PR: 156596
Tested by: adrian @
MFC after: 1 week
identifies the tested condition for _PRT as "BYTE value of 0", so the
remaining part of the conditionals is sufficient.
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
This is to avoid a witness warning about a waiting memory allocation in
the evnt hanlder registration code.
Reported by: markj
MFC after: 3 days
X-MFC with: r277795
Xenstore user-space device has two problems currently:
- It does not correctly handle concurrent clients, because it's storing
each client data in dev->si_drv1.
- It does not correctly free this data when the client closes the device.
In order to solve both of this issues store the per-client data using
cdevpriv, which also comes with a hook in order to perform the necessary
cleanup on device close.
While there also make the device eternal.
Sponsored by: Citrix Systems R&D
Reported and Tested by: thompsa
MFC after: 2 weeks
Now compiler does not need any help.
The patch does not change generated code.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor), glebius
It makes sfxge_tso_state smaller and even makes tso_start_new_packet()
few bytes smaller. Data used to calculate packet size are used nearby,
so it should be no problems with cache etc.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor), glebius
has been removed and the driver has been greatly simplified and
optimised for FreeBSD. The driver is currently not built by default.
Requested by: Bruce Simpson <bms@fastmail.net>
This probably supports other devices based on SeaBIOS, which need
to be added to the smbios based quirks table.
The functionality has been ported from DragonFlyBSD and adapted
to FreeBSD's more general purpose environment.
Devices not covered by a quirk shouldn't be affected at all. Thanks
to jhb and kostikbel for reviewing the code.
Reviewed by: kostikbel, jhb
Approved by: jhb, kostikbel
Differential Revision: https://reviews.freebsd.org/D1802
1. handle errors from nm_config(), if any (none of the FreeBSD drivers
currently returns an error on this function, so this change
is a no-op at this time
2. use a full memory barrier on ioctls
interrupts are enabled and the NIC is awake (think: loading a module)
then there's a not-quite-zero window where we'll get an interrupt
for the device before the attach method is called to finish setting
up the hardware.
Since I grab locks in ath_intr() to check various things, the locks
need to be ready much earlier.
- Use IEEE80211_F_DATAPAD;
- (c->ic_flags & IEEE80211_CHAN_PASSIVE) -> IEEE80211_IS_CHAN_PASSIVE(c);
- Convert ackfailcnt to int (there is dereference to *(int *) in ieee80211_ratectl_tx_complete());
- Fix & move cleanup to the end in wpi_rx_done();
- Add missed lock in wpi_update_beacon();
- Try to fix powersave.
PR: kern/197143
Submitted by: Andriy Voskoboinyk <s3erios@gmail.com>
especially on native monitor resolutions. This one essentially matches X11
default pointer.
Differential Revision: https://reviews.freebsd.org/D1801
No objection from: emaste
Approved by: adrian, dumbbell
o Ensure we use correct bank for MSK register
o Save and restore current bank in interrupt handler
o Stop TX watchdog on fatal errors
o Use right register for EPH status
This fixes operation on ARMv8 Foundation Model
Reviewed by: benno@
endpoint less frequently to make the sample rate adjustment more
accurate. This should resolve problems with the DN32-USB module for
Midas audio systems and possibly other similar products from Klark
Teknik.
MFC after: 3 days
Drivers (ULDs) and the base if_cxgbe driver.
Track the per-adapter activation of ULDs in a new "active_ulds" field.
This was done pretty arbitrarily before this change -- via TOM_INIT_DONE
in adapter->flags for TOM, and the (1 << MAX_NPORTS) bit in
adapter->offload_map for iWARP.
iWARP and hw-accelerated iSCSI rely on the TOE (supported by the TOM
ULD). The rules are:
a) If the iWARP and/or iSCSI ULDs are available when TOE is enabled then
iWARP and/or iSCSI are enabled too.
b) When the iWARP and iSCSI modules are loaded they go looking for
adapters with TOE enabled and enable themselves on that adapter.
c) You cannot deactivate or unload the TOM module from underneath iWARP
or iSCSI. Any such attempt will fail with EBUSY.
MFC after: 2 weeks
This is a sync against iwn(4) and openbsd.
- Add power management support;
- Add background scanning support;
- Fix few LORs;
- Handle rfkill switch state changes properly;
- Fix recovering after firmware failure;
- Add more error checking;
- Cleanup & disable by default debug output;
- Update macroses names;
- Other various fixes;
- Add IBSS support:
- don't set data_ntries field for management frames;
- Add AHDEMO support:
- fix padding;
- Sync eeprom functions;
- Use CMD_RXON_ASSOC where possible;
- Enable HW CCMP encryption/decryption for pairwise keys;
- Fix filter flags for CMD_RXON.
Tested (by submitter) - iwn 3945 NIC. I have one somewhere; I'll
validate this later on and revert it if it's a problem.
Thanks!
PR: 197143
Submitted by: Andriy Voskoboinyk <s3erios@gmail.com>
particular, updates to the watchdog should no longer sleep.
- Add a new IPMI_IO_LOCK for low-level I/O access. Use this for
kcs_polled_request() and smic_polled_request().
- Add a new backend callback "ipmi_driver_request" to handle a driver
request. The new callback performs the request sychronously for KCS
and SMIC. SSIF still defers the work to the worker thread since the
worker thread sleeps during request processing anyway.
- Allocate driver requests on the stack rather than using malloc().
Differential Revision: https://reviews.freebsd.org/D1723
Tested by: scottl
MFC after: 2 weeks
allows the user to request administrative changes to individual devices
such as attach or detaching drivers or disabling and re-enabling devices.
- Add a new /dev/devctl2 character device which uses ioctls for device
requests. The ioctls use a common 'struct devreq' which is somewhat
similar to 'struct ifreq'.
- The ioctls identify the device to operate on via a string. This
string can either by the device's name, or it can be a bus-specific
address. (For unattached devices, a bus address is the only way to
locate a device.) Bus drivers register an eventhandler to claim
unrecognized device names that the driver recognizes as a valid address.
Two buses currently support addresses: ACPI recognizes any device
in the ACPI namespace via its full path starting with "\" and
the PCI bus driver recognizes an address specification of
'pci[<domain>:]<bus>:<slot>:<func>' (identical to the PCI selector
strings supported by pciconf).
- To make it easier to cut and paste, change the PnP location string
in the PCI bus driver to output a full PCI selector string rather
than 'slot=<slot> function=<func>'.
- Add a devctl(3) interface in libdevctl which provides a wrapper around
the ioctls and is the preferred interface for other userland code.
- Add a devctl(8) program which is a simple wrapper around the requests
supported by devctl(3).
- Add a device_is_suspended() function to check DF_SUSPENDED.
- Add a resource_unset_value() function that can be used to remove a
hint from the kernel environment. This is used to clear a
hint.<driver>.<unit>.disabled hint when re-enabling a boot-time
disabled device.
Reviewed by: imp (parts)
Requested by: imp (changing PCI location string)
Relnotes: yes
a dependency. This ensures "ifconfig cxl<n> ..." does the right thing
even when it's run with no driver loaded.
if_cxl.ko is the tiniest module in /boot/kernel.
MFC after: 2 weeks
Lock name should include interface name.
Tx queue and event queue lock name should include queue number.
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
Allow access to statistics data not only from sysctl handlers.
Submitted by: Boris Misenov <Boris.Misenov at oktetlabs.ru>
Sponsored by: Solarflare Communications, Inc.
Approved by: gnn (mentor)
initiator iSCSI offload. Pass maximum data segment size supported by
chosen offload module to iscsid(8), and make iscsid(8) not try to negotiate
anything larger than that.
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
ISR that are normally clear. RST is one, though in some overflow cases
it can be set. RDC is only set when a remote DMA is finished from the
memory mapped memory to the transmit rings, which we poll fore in the
code with ED_LOCK around the operation that would set it.
KVM clock shares the same data structures between the guest and the host
as Xen so it makes sense to just have a single copy of this code.
Differential Revision: https://reviews.freebsd.org/D1429
Reviewed by: royger (eariler version)
MFC after: 1 month
