Commit Graph

298 Commits

Author SHA1 Message Date
Justin T. Gibbs
1ffa43c082 Detect and report dataphase overruns. Put the adapter into 'Bit Bucket'
mode when this occurs and allow the target to complete the transaction.
Force a retry on overruns since they are usually caused by termination or
cable problems.
1996-06-09 17:33:18 +00:00
Justin T. Gibbs
1d40e2f2c5 Hopefully fix the parity problem and the hang on message reject for good. 1996-06-08 06:54:06 +00:00
Justin T. Gibbs
e5442bc690 Don't use the auto ATN on parity error feature. It may be the source
of our parity handling problems.
1996-05-31 06:30:15 +00:00
Justin T. Gibbs
e1ca90bc57 Fix regression. It seems that you need at least one instruction between
seeing SPIORDY and checking for PHASEMIS.  My last change turned out to
be less cosmetic then I thought.

Pointed out by: Satoshi Asami <asami@cs.berkeley.edu>,
		Faried Nawaz <fn@pain.csrv.uidaho.edu
1996-05-30 14:31:08 +00:00
Justin T. Gibbs
56981243dd Merge in changes for NetBSD/OpenBSD.
Cosmetic change to p_mesgout code so that it "looks" the same as what
is done in the inb* routines.
NetBSD/OpenBSD support Submitted by:Noriyuki Soda <soda@sra.co.jp>,
				    Pete Bentley <pete@demon.net>,
				    Charles M. Hannum <mycroft@mit.edu>,
				    Theo de Raadt <deraadt@theos.com>
1996-05-30 07:18:39 +00:00
Justin T. Gibbs
070d32b1a9 Fix a race condition in p_mesgout* and inb* code that could allow a
phasemiss to sneak by without detection.  This should fix the
Wide/Narrow boot problems that have been reported since this bug
caused the driver ignore a narrow target rejecting wide negotiation.
1996-05-27 23:16:55 +00:00
Justin T. Gibbs
087b79e649 Correct a botched commit from yesturday. It helps to bring over the
right patch file.<sigh>
1996-05-23 15:02:18 +00:00
Justin T. Gibbs
61538c3003 Enable/Disable Ultra mode on a per target basis. This allows the driver
to use the full range of settings from 3.6-20MHz on any target.
1996-05-21 18:32:23 +00:00
Justin T. Gibbs
990f21682c One more linux -> __linux__ 1996-05-10 16:28:00 +00:00
Justin T. Gibbs
c2278994ed aic7xxx.seq:
Change #ifdef linux to #ifdef __linux__

aic7xxx_reg.h:
Remove unneeded BOFF_60BCLOCKS
define CHIPRSTACK to be the same as CHIPRST
define RESET_SCSI and CHANNEL_B_PRIMARY bits
All of these aer used during the setup of adapters.
1996-05-10 16:11:03 +00:00
Justin T. Gibbs
0a44712261 Implement SCB paging. This allows up to 255 active commands on
aic7770 >= Rev E, aic7850, aic7860, aic7870, and ai7880 based controllers.

Make findSCB safer for non-tagged commands when tagged commands are
active on the controller.  The symptoms of this problem were
"Overlapped commands attempted" messages during error recovery
attempts.

Compact scratch ram usage.  This leaves 8 bytes free for future use.

Clean up some comments.

aic7xxx_reg.h:
Update my copyright.
1996-04-20 21:20:31 +00:00
Justin T. Gibbs
c2c5fd345d aic7xxx.seq:
Fix support for the aic7850 by looking only at the relavent bits of the
    QINCNT.  The 7850 puts random garbage in the high bits and all my attempts
    to determine the cause of this failed.  This approach does seem to work
    around the problem.

    Don't trust SCSIPERR to tell us when there is a parity error.  On
    some revs of the 7870 and the 7880, this bit follows the parity of
    the current byte.  Instead of using a SEQINT to tell the kernel,
    re-enable the standard parity error interrupt since it seems to pause
    the sequencer right at the time of the error which is the effect we were
    looking for anyway.

aic7xxx_reg.h:
    Remove PARITY_ERROR seqeuncer interrupt type, its no longer used.

    Define QCOUNTMASK as the SRAM location for the mask to use on the
    QINCNT register.  QCOUNTMASK is determined by the number of SCBs
    supported by the device we're working on.

aic7xxx_asm.c
    Properly check the return value of fopen, and define the arg list
    in getopt correctly.
    Submitted by: Pete Bentley <pete@demon.net>
1996-03-31 03:02:37 +00:00
Justin T. Gibbs
75f0b9d070 Reset the DMA control register whenever we reset the sequencer.
Clear LASTPHASE on busfree so the kernel driver can tell that the
   sequencer is idle.
Fix some comments to reflect reality.
1996-03-10 07:02:32 +00:00
Justin T. Gibbs
5327d59536 Performance optimizations. Unroll all bcopies. Use PIO to transfer SCBs
since setting up the DMA is too costly.  Restructure for efficiency.

Pause the sequencer when a parity error occurs so that the kernel driver
knows during which phase the error was encountered.
1996-01-29 03:12:06 +00:00
Justin T. Gibbs
d2c8692ad0 Take a different approach to the SPIORDY race condition. Simply clear
SPIORDY just before we ack on the bus so that there is no chance to
see SPIORDY for the same byte twice.

Make some small modifications so that the Linux aic7xxx driver can use
our sequencer and register definition files verbatum.
1996-01-11 06:17:49 +00:00
Justin T. Gibbs
bff79954c2 Change the inb and outb routines slightly. It seems that waiting for
SPIORDY after polling REQINIT is a bad idea.
1996-01-09 16:14:03 +00:00
Justin T. Gibbs
78aeaf6139 aic7xxx.seq:
Add the same type of safeguards we use in the mesg_in phase to the mesg_out
phase.

aic7xxx_reg.h:
Add definitions for the DSCommand register for PCI adapters.
1996-01-07 19:18:28 +00:00
Justin T. Gibbs
a27c063027 Bring back the more heavy-weight version of the mesgin inb routines. Davidg's
testing made me think that some of the checks were superfluous, but
wcarchive (and Amancio) know better.
1996-01-05 16:11:49 +00:00
Justin T. Gibbs
67e73a53fc Null terminate execl's argument list.
Submitted by: Ron Lenk <rlenk@widget.xmission.com>
1996-01-05 01:48:07 +00:00
Justin T. Gibbs
adf516474d The long awaited stability patch set for the aic7xxx driver:
1) Use cpp to preprocess the sequencer code.

2) Convert all "magic numbers" to #defines shared by the sequencer and
   kernel driver via the aic7xxx_reg.h file.  (The assembler still needs
   to be re-written in lex/yacc to allow ~|& type constructions).

3) Raise ATN on parity errors for "in" phases and send an initiator detected
   error or message-in parity error message as appropriate.

4) Turn off the reselection hardware from the time or a (re)connection to
   busfree.  It seems that some fast targets were able to reconnect before
   the sequencer was able to see busfree.

5) The message buffer is considered "in-use" when there is a positive length
   count.  The ACTIVE_MSG flag was unnecesary.

6) Properly set SCB_NEXT_WAITING to SCB_LIST_HEAD in scbs being added to
   the waiting scb list.  This is a change in how the list code works to
   facilitate some planned work in the reset code.

7) The fields in the SCB have be re-arranged to be quad-word aligned.

8) The inb code has been rewritten to catch phasemisses and be more efficient.

9) Go back to "snooping the bus" to determine if the incomming identify
   message will be followed by a simple queue message.  Its much faster than
   doing a search through the SCBs.

10) Implement better tag range checking for incomming tags.

11) Make sdtr_to_rate more accurate (use 25 instead of 24 in calculations -
    must have been asleep that night).

12) Rearrange some routines to reduce code complexity and size.

13) Update comments and formatting.

14) Fixed bugs I've forgotten about??

Reviewed by: David Greenman <davidg@FreeBSD.org>
1996-01-03 06:25:32 +00:00
Justin T. Gibbs
157b011439 Fix the long dreaded Wide bug and enable WIDEODD for reads. 1995-11-07 05:31:28 +00:00
Justin T. Gibbs
3e4756a1ce Move aic7xxx register definitions from i386/scsi/aic7xxx.c to this file.
The hope is to make the sequencer and kernel code share this file, but
some work on our sequencer assembler will be needed first.
1995-11-05 04:37:25 +00:00
Justin T. Gibbs
1fa2b6b3da Only or in CLRCHN in SXFRCTL0. All other bits in this register are
initialized by the kernel driver now.
1995-10-29 05:56:31 +00:00
Justin T. Gibbs
fca911ecf3 Set SCSIGO generically before we determine the phase instead of doing it
in each phase routine.  Saves a few instructions.

Be more careful in how we deal with SXFRCTL0.  Or in the control bits of
interest instead of using mvi.  The kernel driver will set the ULTRAEN
bit of SXFRCTL0 if we are using Ultra (20MHz) mode and we don't want to
clobber it.

In sdtr_to_rate divide by two if we are in ultra mode to get the correct
setting since its a 20MHz instead of 10MHz scale.
1995-10-26 23:54:13 +00:00
Justin T. Gibbs
1b2a3cf51a Clean up the mesgin code to make it easier to read with proceedure lables
that are based on what mesage is being processed instead of just numbers.

Order the tests for incoming message type by level of occurance.
1995-08-06 05:15:45 +00:00
Justin T. Gibbs
71fb7601c2 Total rewrite of the dataphase sections of the sequencer. This was done
to replace the very poor, original implementation of Scatter/Gather operations.

Use a bit (that was freed up with the rewrite above) in the SCB control byte
to designate commands that should allow disconnection.  The kernel driver
makes this decision now instead of the sequencer since the sequencer can't
do the indexing very efficiently.

This commit drops the sequencer from 426 instructions to 390 most likely
freeing enough space to do a target mode implementation.
1995-08-05 17:31:39 +00:00
Justin T. Gibbs
116616a829 Fix two race conditions.
The first could occur because the original code would continue to reset
the SCSIID register while waiting for a selection.  This could potentially
conflict with a reconnect since a successfull reconnect will also set the
SCSIID register.  The fix is to use a separate wait loop after starting
a selection (as was done a few revisions ago).

The second probably never happens, but it was possible for a target to
reconnect while there was a pending SCB on the waiting list and not get
noticed.  The fix was to remove a supurflous check of the scb waiting
list.
1995-08-05 06:59:17 +00:00
Justin T. Gibbs
4dc2fc9088 Pause the sequencer when message only requests complete. This allows the
kernel driver to know the exact state of the sequencer after a BUS DEVICE
RESET or ABORT completes so it can properly clean up the request.
1995-07-31 08:21:59 +00:00
Justin T. Gibbs
475791c882 Change SCB_LIST_NULL to 0xff from 0x10 to allow for 255 commands. This
is needed for 3940 support.

Have tagged commands look to see if a target is "busy" with a non tagged
command before executing.  This prevents overlapped tagged and non tagged
commands which can happen since request sense commands are not tagged.
1995-07-04 20:58:57 +00:00
Rodney W. Grimes
9b2e535452 Remove trailing whitespace. 1995-05-30 08:16:23 +00:00
David Greenman
57cb71573d Fixes to the aic7xxx sequencer code and device driver from Justin Gibbs:
1) If a target initiated a sync negotiation with us and happened to chose a
value above 15, the old code inadvertantly truncated it with an "& 0x0f".
If the periferal picked something really bad like 0x32, you'd end up with
an offset of 2 which would hang the drive since it didn't expect to ever
get something so low.  We now do a MIN(maxoffset, given_offset).

2) In the case of Wide cards, we were turning on sync transfers after a
sucessfull wide negotiation.  Now we leave the offset alone in the per
target scratch space (which implies asyncronous transfers since we initialize
it that way) until a syncronous negotation occurs.

3) We were advertizing a max offset of 15 instead of 8 for wide devices.

4) If the upper level SCSI code sent down a "SCSI_RESET", it would hang the
system because we would end up sending a null command to the sequencer.  Now
we handle SCSI_RESET correctly by having the sequencer interrupt us when it
is about to fill the message buffer so that we can fill it in ourselves.
The sequencer will also "simulate" a command complete for these "message only"
SCBs so that the kernel driver can finish up properly.  The cdplay utility
will send a "SCSI_REST" to the cdplayer if you use the reset command.

5) The code that handles SCSIINTs was broken in that if more than one type
of error was true at once, we'd do outbs without the card being paused.
The else clause after the busfree case was also an accident waiting to
happen.  I've now turned this into an if, else if, else type of thing, since
in most cases when we handle one type of error, it should be okay to ignore
the rest (ie if we have a SELTO, who cares if there was a parity error on
the transaction?), but the section should really be rewritten after 2.0.5.
This fix was the least obtrusive way to patch the problem.

6) Only tag either SDTR or WDTR negotiation on an SCB.  The real problem is
that I don't account for the case when an SCB that is tagged to do a particular
type of negotiation completes or SELTOs (selection timeout) without the
negotiation taking place, so the accounting of sdtrpending and wdtrpending
gets screwed up.  In the wide case, if we tag it to do both wdtr and sdtr,
it only performs wdtr (since wdtr must occur first and we spread out the
negotiation over two commands) so we always have sdtrpending set for that
target and we never do a real SDTR.  I fill properly fix the accounting
after 2.0.5 goes out the door, but this works (as confirmed by Dan) on
wide targets.

Other stuff that is also included:

1) Don't do a bzero when recycling SCBs.  The only thing that must explicitly
be set to zero is the scb control byte which is done in ahc_get_scb.  We also
need to set the SG_list_pointer and SG_list_count to 0 for commands that do
not transfer data.

2) Mask the interrupt type printout for the aic7870 case.  The bit we were
using to determine interrupt type is only valid for the aic7770.


Submitted by:	Justin Gibbs
1995-05-17 07:06:02 +00:00
Justin T. Gibbs
c28447da4c Restructure the arbitration loop to allow for reselections that win out over
the adapter's selections.  Many fast periferals were getting upset when
the sequencer decided to rearbitrate after the device had already won
arbitration.  This also forced the creation of a list threaded through
the SCBs (since we don't have enough space anywhere else) of commands that
are awaiting reselection.  This list is run down before any new transactions
from the input queue are allowed.  The list is appened to whenever we begin
a selection (simple case since the selecting device is always at the head)
and by the kernel driver whenever a request sense occurs.  In the common
case, the list is only one element long, but when a reselection wins out
over a selection and that reselection generates a request sense, the
outstanding selection required for the retreval of the sense code grows
the list.  On machines with many targets, this might cause the list to grow
large, so this solution, which will allow up to the maximum number of I/O
requests capible of the card elements in the list, was chosen.  The list
manipulation is trivial and adds three sequencer instructions of overhead
to the selection phase.

This fixes the "target busy" errors from micropolis drives and the bursty
I/O problem when performing I/O between a Quantum Grand Prix and any other
device.  I anticipate that this will correct many of the problems that
have been reported with this driver.

Reviewed by: Wcarchive and David Greenman
1995-04-27 17:44:27 +00:00
Justin T. Gibbs
3cddb2a3e2 John Aycock's BSD copyrighted sequencer assembler and sequencer code. This
is identical to the older version, just the copyright has changed.  Many
thanks go to Dean Gehnert of the Linux camp who went the extra mile to make
this happen.

Other changes:

Update assembler man page to include the -v and -D options

Merge in Dean's latest changes to the assembler

Have the sequencer do a MSG_REJECT when the negotiated syncronous rate
is lower than the adapter supports.  This forces asyncronous mode which
is faster at these rates anyway.

This code will be moved shortly to the non-gpld portion of the tree.
1995-04-15 21:45:56 +00:00
Justin T. Gibbs
0b000afb3b More code optimizations. Use a slightly different approach to decide
whether a reconnecting target is a tagged device or not.
1995-04-09 06:40:16 +00:00
Justin T. Gibbs
cc865dd008 Off by one error in -MSG-START+0 was just Justin being tired -- revert to
old value.

Remove unnecessary check for active messages in setup SCB.  This same test
would also jump to p_mesgin_done which would "ACK" an extra time possibly
confusing the target.

Tell the kernel driver whenever we send an ABORT_TAG message.
1995-04-01 19:51:40 +00:00
Justin T. Gibbs
5743c01c3f Major overhaul of the aic7xxx driver:
- Report valid residual byte counts.  We actually pause the sequencer
	  when the residual is non-zero.  I thought about using DMA to do this,
	  bus sequencer program space is tight.

	- Fix embarassing off by one error in the computation of a 2's
	  compliment variable.  This was most likely the cause of the
	  many problems reported with the tagged queuing code.

	- Handle "MAX_SYNC" as a special case (ie we are the ones starting
	  the sync negotiation sequence).  This was done so that the target
	  scratch area can be initialed to 0 offset (asyncronous transfers)
	  safely.  The initialization to 0 (was 15) is necessary since in
	  some cases a Wide negotiation could run into problems if SCSIRATE
	  was set wrong and we went into data(in/out).

	- Trim the DMA routines a little by using some procedures.  Net
	  effect is more functionality with 3 less instructions after this
	  update.

	- Toggle the WIDEODD bit of the DFCNTRL whenever this is not the
	  last SG block.  It has no effect in the 8bit bus configuration,
	  but in the Wide configuration ensures that the overlap byte is
	  held in the SCSI block if the transfer is odd so it will end
	  up in the next SG (the correct behavior).
1995-03-31 14:06:02 +00:00
Justin T. Gibbs
b8d72a5ae8 Make the aic7xxx assembler take quoted strings as a single token.
Make $Id the version variable which required the quoted string "feature".
1995-03-17 23:54:17 +00:00
Justin T. Gibbs
06f0e1ceb8 Be careful to maintain the bits in SBLKCTL that are reserved. 1995-03-07 09:00:44 +00:00
Justin T. Gibbs
7325b76b7d Add tagged queueing support to the aic7xxx sequencer code. 1995-02-22 01:37:52 +00:00
Justin T. Gibbs
1bca1a0922 Have version number track CSV version number. No other change. 1995-02-03 17:18:44 +00:00
Justin T. Gibbs
c135d93bbf aic7xxx.c:
Print out the length of the compiled sequencer program.

aic7xxx.seq:
	More optimizations.  Replace generic bcopy routine with bcopy_3
and bcopy_4 (ie unroll the loops) since these are the only two cases used.
Initialize SIMODE1 and SXFRCTL1 from the kernel in ahc_init instead of
at each selection/reselection since this is expensive and only needs to
be done once.  Condense function returns into previous instruction if possible.
Reorder some sections to kill superflous jumps.  These optimizations kill
the ~150k/s penalty adding support for Twin/Wide cards was costing since
the last place in the commaon path of execution where we had to do ugly,
convoluted testing for the type of card in the sequencer has gone away.
Next stop tagged queuing and target mode.
1995-01-22 00:46:53 +00:00
Justin T. Gibbs
0d56403998 At $Ids to all files. Have the sequencer use DMA to tranfer its SCB
(SCSI control block) instead of having the host PIO it down.  Also
reimplement WDTR and SDTR optimization to remove code in the sequencer
and place the responsibility of knowing when to initiate SDTR or WDTR
on the kernel driver.  This vastly shortens the sequencer program yet
yeilds the same performance.
1995-01-16 16:31:21 +00:00
Justin T. Gibbs
20c5e65572 Full support for 294x and Wide devices. Fixed month old bug in the SCSI
sense retrieval code that messed up CDROM devices.  This code will also
responde correctly to SDTR and WDTR messages from devices that start a
negotiation sequence.
1995-01-13 02:22:11 +00:00
Justin T. Gibbs
8ff1d93efb Update the sequencer code to handle both channels of Twin channel devices.
You can now sling 14 devices off of a 274xT.  In the process of adding
twin channel support, I removed all evident restrictions on supporting
Wide channeled devices, but I do not have a Wide controller to test them
on.

aic7770_seq.h, the pre-compiled header, is no longer needed since config
handles this dependancy.
1994-12-31 19:26:54 +00:00
Justin T. Gibbs
cb0d548bf4 Merge in latest Linux sequencer code release with my changes. This should
make the sequencer code fully compatible with the aic7870 (ie 294x adaptors).
I've also added to my local mods putting the sequencer into "FASTMODE" clock.
This gives upwards of 2M/sec write preformance improvement in some scenarios.
There haven't been any reports of this causing problems, and I have been
reaping the benifits of it for more than a week now.

This also includes a new version of the pre-generated file <ugh>

Obtained from: John Aycock (aycock@cpsc.ucalgary.ca) and myself
1994-11-29 23:04:23 +00:00
Justin T. Gibbs
8d244f9e3b Previous changes to the sequencer compiler backed out. We go back to
generating the .h file, and a pregenerated file is included.
1994-11-18 09:11:35 +00:00
Jordan K. Hubbard
9cc6cb724f Make the compiler spit out a .c file instead of a .h file. 1994-11-18 08:17:20 +00:00
Justin T. Gibbs
0ef8c3017a John Aycock's aic7770 sequencer code and assembler. There is currently
a discussion going on about removing this code from the burden of the
GPL, but it won't happen before Beta, and this code should be tested
before release.

Supports 27/2842 class adaptec cards and is almost capable of supporting
aic7870 based adapters (294X series cards).  It does not support Wide
controllers or the second channel on Twin boards although I have work in
progress on getting both channels and running.

I have also added a few performance improvements to this version that give
us approximately a 25% boost over the original driver.  These patches have
been submitted to the author.

Obtained from: Linux aic7770 driver (John Aycock - aycock@cpsc.ucalgary.ca)
1994-11-17 20:19:10 +00:00