side effect of something else using them. If they haven't been loaded
already but you want to use them, say for configuring a jail, you're out
of luck.
So add a knob to always load the default rulesets. While I'm here document
the other devfs_ knobs in rc.conf.5.
This should have been included in change 230592.
The supported hardware section still needs some updating to reflect
the current reality.
MFC after: 3 days
ext4 but that can be used in ext3 mode.
Also adjust the internal inode to carry the birthtime,
like in UFS, which is starting to get some use when
big inodes are available.
Right now these are just placeholders for features
to come.
Approved by: jhb (mentor)
MFC after: 2 weeks
- Increase probing order for ECDT table to match HID-based probing.
- Decrease probing order for HPET table to match HID-based probing.
- Decrease probing order for CPUs and system resources.
- Fix ACPI_DEV_BASE_ORDER to reflect the reality.
every 30 seconds. This spike in I/O caused the system to pause every
30 seconds which was quite annoying. So, the way that sync worked
was changed so that when a vnode was first dirtied, it was put on
a 30-second cleaning queue (see the syncer_workitem_pending queues
in kern/vfs_subr.c). If the file has not been written or deleted
after 30 seconds, the syncer pushes it out. As the syncer runs once
per second, dirty files are trickled out slowly over the 30-second
period instead of all at once by a call to sync(2).
The one drawback to this is that it does not cover the filesystem
metadata. To handle the metadata, vfs_allocate_syncvnode() is called
to create a "filesystem syncer vnode" at mount time which cycles
around the cleaning queue being sync'ed every 30 seconds. In the
original design, the only things it would sync for UFS were the
filesystem metadata: inode blocks, cylinder group bitmaps, and the
superblock (e.g., by VOP_FSYNC'ing devvp, the device vnode from
which the filesystem is mounted).
Somewhere in its path to integration with FreeBSD the flushing of
the filesystem syncer vnode got changed to sync every vnode associated
with the filesystem. The result of this change is to return to the
old filesystem-wide flush every 30-seconds behavior and makes the
whole 30-second delay per vnode useless.
This change goes back to the originally intended trickle out sync
behavior. Key to ensuring that all the intended semantics are
preserved (e.g., that all inode updates get flushed within a bounded
period of time) is that all inode modifications get pushed to their
corresponding inode blocks so that the metadata flush by the
filesystem syncer vnode gets them to the disk in a timely way.
Thanks to Konstantin Belousov (kib@) for doing the audit and commit
-r231122 which ensures that all of these updates are being made.
Reviewed by: kib
Tested by: scottl
MFC after: 2 weeks
a credential structure would corrupt it. This happened when the
p argument was != NULL. However, I now realize that the copying of
open credentials should only happen for p == NULL, since that indicates
that it is a read-ahead or write-behind. This patch fixes this.
After this commit, r228827 could be reverted, but I think the code is
clearer and safer with the patch, so I am going to leave it in.
Without this patch, it was possible that a NFSv4 VOP_SETATTR() could have
changed the credentials of the caller. This would have happened if
the process doing the VOP_SETATTR() did not have the file open, but
some other process running as a different uid had the file open for writing
at the same time.
MFC after: 5 days
guarantee that all UFS inode metadata changes results in the dirtiness
of the inodeblock. Due to missed inodeblock updates, syncer was
required to fsync each mount point' vnode to guarantee periodic
metadata flush.
Reviewed by: mckusick
Tested by: scottl
MFC after: 2 weeks
not bailing out early when a hole is encountered in the direct block list.
Print NULL block pointers in the direct block list. Simplify the
code that prints the fragment count.
Match the style of the existing code.
Reviewed by: mckusick
MFC after: 1 week
rpcgen will search the current PATH for the preprocessor. This makes it
possible to run a preprocessor built during the cross-tools stage of
buildworld.
MFC after: 1 week
radar parameters for the AR5416 and later NICs.
These parameters have been tested on the following NICs:
* AR5416
* AR9160
* AR9220
* AR9280
And yes, these will return radar pulse parameters and (for AR9160 and later)
radar FFT information as PHY errors.
This is again not enough to do radar detection, it's just here to faciliate
development and validation of radar detection algorithms.
The (pulse, not FFT) decoding code for AR5212, AR5416 and later NICs exist
in the HAL.
This code is disabled for now as generating radar PHY errors can quickly
cause issues in busy environment.s Some further debugging of the RX path
is needed.
Finally, these parameters are likely not useful for the AR5212 era NICs.
The madwifi-dfs branch should have suitable example parameters for the
11a era NICs.
If the sentence starts with a multiple of eight spaces, the sentence
should in almost all practical cases have started with tabs instead.
Replace these spaces by tabs.
when the child process execs daemon's target program thanks to flock(2)
semantics. So, we apparently have to leak the open pidfile's file
descriptor to keep the lock for the pidfile(3) functions to work properly.
Test case demonstrated by trociny:
ref8-amd64:/home/trociny% uname -r
8.2-STABLE
ref8-amd64:/home/trociny% daemon -p /tmp/sleep.pid sleep 10
ref8-amd64:/home/trociny% daemon -p /tmp/sleep.pid sleep 10
daemon: process already running, pid: 19799
kopusha:~% uname -r
10.0-CURRENT
kopusha:~% daemon -p /tmp/sleep.pid sleep 10
kopusha:~% daemon -p /tmp/sleep.pid sleep 10
kopusha:~%
preprocessor to run. Previously, it always ran /usr/bin/cpp, unless you
used the -Y option, and even then you could not set the basename. It
also attempted to run /usr/ccs/lib/cpp for SVR4 compatibility, but this
is obsolete, and has been removed.
Note that setting RPCGEN_CPP to a command with arguments is supported,
though the command line parsing is simplistic. However, setting it to
e.g. "gcc46 -E" or "clang -E" will lead to problems, because both gcc
and clang in -E mode will consider files with unknown extensions (such
as .x) as object files, and attempt to link them.
This could be worked around by also adding "-x c", but it is much safer
to set RPCGEN_CPP to e.g. "cpp46" or "clang-cpp" instead.
MFC after: 1 week
list. If softdep_sync_buf() discovers such dependency, it should do
nothing, which is safe as it is only waiting on the parent buffer to
be written, so it can be removed.
Committed on behalf of: jeff
MFC after: 1 week
mnt_noasync counter to temporary remove MNTK_ASYNC mount option, which
is needed to guarantee a synchronous completion of the initiated i/o
before syscall or VOP return. Global removal of MNTK_ASYNC option is
harmful because not only i/o started from corresponding thread becomes
synchronous, but all i/o is synchronous on the filesystem which is
initiated during sync(2) or syncer activity.
Instead of removing MNTK_ASYNC from mnt_kern_flag, provide a local
thread flag to disable async i/o for current thread only. Use the
opportunity to move DOINGASYNC() macro into sys/vnode.h and
consistently use it through places which tested for MNTK_ASYNC.
Some testing demonstrated 60-70% improvements in run time for the
metadata-intensive operations on async-mounted UFS volumes, but still
with great deviation due to other reasons.
Reviewed by: mckusick
Tested by: scottl
MFC after: 2 weeks
This small utility can be used to `sanitize' the whitespace in source
code. It does the following things:
Global:
- Remove empty lines at the beginning and the end of a file.
- Merge successive empty lines into a single empty line.
Per-line:
- Remove trailing whitespace.
- Merge spaces preceeding tabs into the tabs.
It operated on stdin/stdout. This means that if you use vi(1), you can
just run :%!fixwhite to reorganize the file.
