Mainly link errors interrupts should only be activated on fully linked port,
otherwise noise on lanes can cause livelock. But we don't have error
counters yet, so leave these interrupts disabled.
PAT_WRITE_BACK is x86-only, whereas sys/dev/xen could be shared
between multiple architectures.
Reviewed by: royger
Differential Revision: https://reviews.freebsd.org/D28831
In the Neoverse N1 SDP PCIe driver we need to map a page shared
between the firmware and the kernel. Previously we would use
pmap_kenter for this, however as this is not standardised between
architectures switch to the common pmap_qenter.
While here fix the error handling code to clean up on failure.
Reviewed by: br
Sponsored by: Innovate UK
Differential Revision: https://reviews.freebsd.org/D28890
Make the pwm_backlight module depend on backlight, so it
has access to the backlight interface symbols. Otherwise you'll
get an error like:
link_elf: symbol backlight_get_info_desc undefined
Signed-off-by: Brett Mastbergen <brett.mastbergen@gmail.com>
MFC after: 3 days
PR: 253765
Add it to the x86 GENERIC and MINIMAL kernels
Sponsored by: Ampere Computing LLC
Submitted by: Klara Inc.
Reviewed by: rpokala
Differential Revision: https://reviews.freebsd.org/D28738
ipmi_ssif will `smbus_request_bus()` to do multiple smbus requests
(which requests the iicbus), and then here in `bread()` we also need to
request the bus because `bread()` takes multiple transactions.
This causes deadlock as it's waiting for the bus it already has without
`IIC_RECURSIVE`.
Sponsored by: Ampere Computing LLC
Submitted by: Klara Inc.
Reviewed by: imp
Differential Revision: https://reviews.freebsd.org/D28742
The previous implementation was reported to try to coalesce packets
in situations when it should not, that resulted in assertion later.
This implementation better checks the first packet of the chain for
the coallescing elligibility.
MFC after: 3 days
Instead of 2-4 socket reads per PDU this can do as low as one read
per megabyte, dramatically reducing TCP overhead and lock contention.
With this on iSCSI target I can write more than 4GB/s through a
single connection.
MFC after: 1 month
Multi page rings are mapped using a single hypercall that gets passed
an array of grants to map. One of the grants in the array failing to
map would lead to the failure of the whole ring setup operation, but
there was no cleanup of the rest of the grant maps in the array that
could have likely been created as a result of the hypercall.
Add proper cleanup on the failure path during ring setup to unmap any
grants that could have been created.
This is part of XSA-361.
Sponsored by: Citrix Systems R&D
- Make frontends call unified CTL core method ctl_datamove_done()
to report move completion. It allows to reduce code duplication
in differerent backends by accounting DMA time in common code.
- Add to ctl_datamove_done() and be_move_done() callback samethr
argument, reporting whether the callback is called in the same
context as ctl_datamove(). It allows for some cases like iSCSI
write with immediate data or camsim frontend write save one context
switch, since we know that the context is sleepable.
- Remove data_move_done() methods from struct ctl_backend_driver,
unused since forever.
MFC after: 1 month
T5 and above have extra bits for the optional filter fields. This is a
correctness issue and not just a waste because a filter mode valid on a
T4 (36b) may not be valid on a T5+ (40b).
MFC after: 2 weeks
Sponsored by: Chelsio Communications
Allow the filter mask (aka the hashfilter mode when hashfilters are
in use) to be set any time it is safe to do so. The requested mask
must be a subset of the filter mode already. The driver will not change
the mode or ingress config just to support a new mask.
MFC after: 2 weeks
Sponsored by: Chelsio Communications
1. Query the firmware for filter mode, mask, and related ingress config
instead of trying to figure them out from hardware registers. Read
configuration from the registers only when the firmware does not
support this query.
2. Use the firmware to set the filter mode. This is the correct way to
do it and is more flexible as well. The filter mode (and associated
ingress config) can now be changed any time it is safe to do so.
The user can specify a subset of a valid mode and the driver will
enable enough bits to make sure that the mode is maxed out -- that
is, it is not possible to set another bit without exceeding the
total width for optional filter fields. This is a hardware
requirement that was not enforced by the driver previously.
MFC after: 2 weeks
Sponsored by: Chelsio Communications
- Implements little-endian support (powerpc64le)
- Adds 'hw.ofwfb.physaddr' kernel parameter so user can manually
provide correct address if it's not detected correctly
- Adds 'hw.ofwfb.argb32_pixel' so user can set it manually if
colors are inverted due to incorrect pixel format (default = 1)
- Automatically selects RGBA32 pixel format if NVidia graphic adapter
is detected (sets hw.ofwfb.argb32_pixel=0)
Machines equipped with NVidia graphic adapters tend to use RGBA32
pixel format. By default ARGB32 pixel format is used, proved to work
on machines equipped with ATI graphic adapter and the onboard adapter
used on Talos II and Blackbird machines from Raptor Computing Systems.
Original patch developed by bdragon
Reviewed by: bdragon, luporl
MFC after: 3 days
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D28604
The ACPI NFIT specification defines a set of "NVDIMM State Flags". These
flags are already reported by `acpidump -t', but this change makes them
available on a per-device basis, in a format that is more easily parsed.
To simplify this, introduce acpi_nfit_get_memory_maps_by_dimm(), which
locates the (ACPI_NFIT_MEMORY_MAP)s associated with a given
(nfit_handle_t).
Reviewed by: mav, cem
Tested by: mav, rpokala (version for stable/12)
MFC after: 3 days
Sponsored by: Panasas
BUS_DMA_NOCACHE should only be used when one needs to guarantee the
created mapping has uncached memory attributes, usually as a result
of buggy hardware. Normal use cases should pass BUS_DMA_COHERENT, to
create an appropriate mapping based on the flags passed to
bus_dma_tag_create().
This should have no functional change, since the DMA tags in this driver
are created without the BUS_DMA_COHERENT flag.
Reported by: mmel
Reviewed by: mmel, Thomas Skibo <thomas-bsd@skibo.net>
MFC after: 3 days
Per the i2c spec, a slave device can stretch SCL idefinitely, so 25ms is
a bit arbitrary in general. smbus does specify an optional timeout
recovery mechanism to be done at about 25~35ms, but the IPMI SSIF spec
says that BMCs don't have any obligation to implement that.
The BMC on Altra seems to mostly respond within 25ms, but occasionally
will stretch SCL for ~300 msec.
Also, the count_us mechanism seems to actually timeout around 25%
earlier than it would claim (timeout really happening around 19ms
instead of 25ms).
Sponsored by: Ampere Computing LLC
Submitted by: Klara Inc.
Reviewed by: manu, imp
Differential Revision: https://reviews.freebsd.org/D28747
In the new ENA-based instances like c6gn, the vector table moved to a
new PCIe bar - BAR1. Previously it was always located on the BAR0, so
the resources were already allocated together with the registers.
As the FreeBSD isn't doing any resource allocation behind the scenes,
the driver is responsible to allocate them explicitly, before other
parts of the OS (like the PCI code allocating MSIx) will be able to
access them.
To determine dynamically BAR on which the MSIx vector table is present
the pci_msix_table_bar() is being used and the new BAR is allocated if
needed.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc
MFC after: 3 days
Read the PF-only hardware settings directly in get_params__post_init.
Split the rest into two routines used by both the PF and VF drivers: one
that reads the SGE rx buffer configuration and another that verifies
miscellaneous hardware configuration.
MFC after: 1 week
Sponsored by: Chelsio Communications
This updates r311987/fb1d9b7f4113d which allowed any number of vectors to be
used. Since we're just attaching one instance, the meaning of more than one
vector is not clear and seems to cause problems. Fall back to old methods for
these cards.
PR: 235016
Submitted by: David Cross
These errors do not clear so to NULL, so the existing check was
treating these failures as success. The rest of do_pass_establish()
then tried to use the listen socket as if it was a connection socket
newly created by syncache_expand().
In addition, for negative return values, do not send a RST to the
peer.
Reported by: Sony Arpita Das @ Chelsio
Reviewed by: np
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D28243
The fallback for __align_up() used by roundup2() uses __typeof__()
which doesn't work for bitfields. This fixes the build on GCC which
uses the fallback.
Reviewed by: arichardson, markj
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D28599
When refill_fl() fails to allocate large (9/16KB) mbuf cluster, it
falls back to safe (4KB) ones. But it still saved into sd->zidx
the original fl->zidx instead of fl->safe_zidx. It caused problems
with the later use of that cluster, including memory and/or data
corruption.
While there, make refill_fl() to use the safe zone for all following
clusters for the call, since it is unlikely that large succeed.
MFC after: 3 days
Sponsored by: iXsystems, Inc.
Reviewed by: np, jhb
Differential Revision: https://reviews.freebsd.org/D28716
FreeBSD when running as a dom0 under Xen is not supposed to access the
run time services directly, and instead should proxy the calls through
Xen using an hypercall interface that exposes access to selected run
time services.
Implement the efirt interface on top of the Xen provided hypercalls.
Sponsored by: Citrix Systems R&D
Reviewed by: kib
Differential revision: https://reviews.freebsd.org/D28621
Introduce a set of hooks for MI EFI public functions, so that a new
implementation can be done. This will be used to implement the Xen PV
EFI interface that's used when running FreeBSD as a Xen dom0 from UEFI
firmware. Also make the efi_status_to_errno non-static since it will
be used to evaluate status return values from the PV interface.
No functional change indented.
Sponsored by: Citrix Systems R&D
Reviewed by: kib, imp
Differential revision: https://reviews.freebsd.org/D28620
Locking the second lock which causes the LOR, can be skipped because
the code updating the shared variables is always executing from the
same USB thread.
lock order reversal:
1st 0xfffff80005cc3840 pcm7:play:dsp7.p0 (pcm play channel, sleep mutex)
@ usb_transfer.c:2342
2nd 0xfffff80005cc3860 pcm7:record:dsp7.r0 (pcm record channel, sleep mutex)
@ uaudio.c:2317
lock order pcm record channel -> pcm play channel established at:
witness_checkorder+0x461
__mtx_lock_flags+0x98
dsp_mmap_single+0x151
vm_mmap_cdev+0x65
devfs_mmap_f+0x143
kern_mmap_req+0x594
sys_mmap+0x46
amd64_syscall+0x12e
fast_syscall_common+0xf8
lock order pcm play channel -> pcm record channel attempted at:
witness_checkorder+0xd82
__mtx_lock_flags+0x98
uaudio_chan_play_callback+0xeb
usbd_callback_wrapper+0x7ec
usb_command_wrapper+0x7e
usb_callback_proc+0x8e
usb_process+0xf3
fork_exit+0x80
fork_trampoline+0xe
Found by: Stefan Ehmann <shoesoft@gmx.net>
MFC after: 1 week
Sponsored by: Mellanox Technologies // NVIDIA Networking
defined by hardware rather than cached one to match HIDIOCGRDESC ioctl.
This fixes errors reported by hid-tools being run against /dev/hidraw#
device node belonging to driver which overloads report descriptor.
MFC after: 1 week
Ignore fantom keyboard state reports entirelly rather than ignore
RollOver states for each key separatelly. Latter results in spurious
release/push pairs of events on each fantom keyboard state report.
Reported by: Jan Martin Mikkelsen <janm_AT_transactionware_DOT_com>
Submitted by: Jan Martin Mikkelsen (initial version)
PR: 253249
MFC after: 1 week
Ignore fantom keyboard state reports entirelly rather than ignore
RollOver states for each key separatelly. Latter results in spurious
release/push pairs of events on each fantom keyboard state report.
Reported by: Jan Martin Mikkelsen <janm_AT_transactionware_DOT_com>
Submitted by: Jan Martin Mikkelsen (initial version)
PR: 253249
MFC after: 1 week
Previously, iscsi_poll() just panicked. This meant if you got a panic
on a box when using the iSCSI initiator, the attempt to shutdown would
trigger a nested panic and never write out a core. Now, CCB's sent to
iSCSI devices (such as the sychronize-cache request in dashutdown())
just fail with a timeout during a panic shutdown.
Reviewed by: scottl, mav
MFC after: 2 weeks
Sponsored by: Chelsio
Differential Revision: https://reviews.freebsd.org/D28455
Since commit 8fa6abb6f4 ("Expose clang's alignment builtins and use
them for roundup2/rounddown2"), clang emits warnings for several
alignment operations in these drivers because the operation is a no-op.
The compiler is arguably being too strict here, but in the meantime
let's silence the warnings by conditionally compiling the alignment
operations.
Reviewed by: arichardson, hselasky
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D28576
My YOGA requires a minimum of 7 to parse w/o an error. Since the memory savings
are trivial and the yoga a popular system, bump the default up to 8. There's no
API/ABI issues in doing this. This hid_item struct isn't exported to userland
and the one libusbhid has is different and only shares a name...
MFC After: 3 days
Reviewed by: wulf@
Differential Revision: https://reviews.freebsd.org/D28543
It appears that production versions of EPYC firmware get the _STA method right
for these nodes. In fact, this workaround breaks on production hardware by
including too many uart nodes. This work around was for pre-release hardware
that wound up not having a large deployment. Move this work around to a kernel
option since the machines that needed it have been powered off and are difficult
to resurrect. Should there be a more significant deployment than is understood,
we can restrict it based on smbios strings.
Discussed with: mmacy@, seanc@, jhb@
MFC After: 3 days
This adds a new sysctl to Wellspring Touchpad driver for controlling
Z-Axis (2-finger vertical scroll) direction "hw.usb.wsp.z_invert".
Submitted by: James Wright <james.wright_AT_digital-chaos_DOT_com>
Reviewed by: wulf
PR: 253321
Differential revision: https://reviews.freebsd.org/D28521
vt is using static buffers for on screen data, the buffer size is
calculated based on maximum supported screen size and 8x16 font.
When using hi-res graphics and very smaller than 8x16 font, we
need to be careful not to overflow static buffers in vt.
Testing: I did test by building smaller buffers than vt currently is using,
royger was testing on actual 4k capable hardware.
MFC after: 1 week
Tested by: royger
X700 family of controllers has limited number of available VLAN
HW filters. Driver did not handle properly a case when user
assigned more VLANs to the interface which had all filters
already in use. Fix that by disabling HW filtering when
it is impossible to create filters for all requested VLANs.
Keep track of registered VLANs using bitstring to be able
to re-enable HW filtering when number of requested VLANs
drops below the limit.
Also switch all allocations to use M_IXL malloc type
to ease detecting memory leaks in the driver.
Reviewed by: erj
Tested by: gowtham.kumar.ks@intel.com
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D28137
Add endiannes conversions in order to support big-endian platforms
Submitted by: Andre Fernando da Silva <andre.silva@eldorado.org.br>
Reviewed by: luporl, alfredo, kadesai (on email)
Sponsored by: Eldorado Research Institute (eldorado.org.br)
Differential Revision: https://reviews.freebsd.org/D26531
- limit maximum segment size to 2048 bytes. Although dwmmc supports a buffer
fragment with a maximum length of 4095 bytes, use the nearest lower power
of two as the maximum fragment size. Otherwise, busdma create excessive
buffer fragments.
- fix off by one error in computation of the maximum data transfer length.
- in addition, reserve two DMA descriptors that can be used by busdma
bouncing. The beginning or end of the buffer can be misaligned.
- Don’t ignore errors passed to bus_dmamap_load() callback function.
- In theory, a DMA engine may be running at time when next dma descriptor is
constructed. Create a full DMA descriptor before OWN bit is set.
MFC after: 2 weeks
