Powermac G5 systems. MSI and several other things are not presently
supported.
The U3/U4 internal device support portions of this change were contributed
by Andreas Tobler.
MFC after: 1 week
This eliminates the only place where we can sleep when calling zio_interrupt().
As a side-effect this can actually improve performance a little as we
allocate one less thing for every I/O.
Prodded by: kib
MFC after: 1 week
avoid calling zio_interrupt() from geom_up thread context. It turns out that
when provider is forcibly removed from the system and we kill worker thread
there can still be some ZIOs pending. To complete pending ZIOs when there is
no worker thread anymore we still have to call zio_interrupt() from geom_up
context. To avoid this race just remove use of worker threads altogether.
This should be more or less fine, because I also thought that zio_interrupt()
does more work, but it only makes small UMA allocation with M_WAITOK.
It also saves one context switch per I/O request.
PR: kern/145339
Reported by: Alex Bakhtin <Alex.Bakhtin@gmail.com>
MFC after: 1 week
so ni_txrate returned 0 which is a invalid result.
- The fourth argument of ieee80211_ratectl_tx_complete() could be not
NULL.
Reported by: Gustau P?rez <gperez at entel.upc.edu>
Tested by: Gustau P?rez <gperez at entel.upc.edu>,
Ian FREISLICH <ianf at clue.co.za>
MFC after: 3 days
Starting something that wants input on login seems strange and can be
dangerous. In some configurations, causing output can be bad, but it is not
as dangerous.
I do not expect this msgs invocation to be uncommented often.
PR: conf/96015
MFC after: 4 days
On a soekris Net5501, if you do a watchdog -t 16, followed by a watchdog
-t 0 to disable the watchdog, and then after some time (16s) re-enable
the watchdog the box reboots immediatly. This prevents also to stop and
restart watchdogd(8).
This is because when you stop the watchdog, the timer is not stoped,
only the hard reset is disabled. So when the timer has elapsed, the C2
event of the timer is set.
But when the hard reset is re-enabled, the event is not cleared and the
box reboots.
The attached patch stops and resets the counter when the watchdog is
disabled and do not disable the hard reset of the timer (if the timer
has elapsed it's too late).
Submitted by: Patrick Lamaizière
- add a moderation value to the Link vector
- allow disabling HW RSC on the 82599 if LRO
is not enabled.
- correct error in the stats code
- change optic type on the 82598 DA device
Thanks to Andrew Boyer for the changes.
We cannot expect that modspace is the last entry in the linker
set and thus that modspace + possible extra space up to PAGE_SIZE
would be contiguous. For the moment do not support more than
*_MODMIN space and ignore the extra space (*).
(*) We know how to get it back but it'll need testing.
Discussed with: jeff, rwatson (briefly)
Reviewed by: jeff
Sponsored by: The FreeBSD Foundation
Sponsored by: CK Software GmbH
MFC after: 4 days
implementation.
- Revert the Sun Fire V890 WAR of r205254. Instead let schizo_pci_bus()
only panic in case of fatal errors as the interrupt triggered by the
error the firmware of these and also Sun Fire 280R with version 7
Schizo caused may happen as late as using the HBA and not only prior
to touching the PCI bus (in the former case the actual error still is
fatal but we clear it before touching the PCI bus).
While at it count and export non-fatal error interrupts via sysctl(9).
- Remove unnecessary locking from schizo_ue().
RFA. Also drop frames that have either CRC error or alignment
error. Normally bad frames are not received at all. But controllers
running in promiscuous mode will receive bad frames. 82557 will
also receive bad frames to receive VLAN oversized frames.
While I'm here mark RNR condition if driver happen to see RNR in
RFA status and restart RU to receive frames again. Because driver
checks all received frames in RX loop, RNR condition could be set
in the middle of RX processing. Just relying on RNR interrupt was
not enough.
This change fixes "Memory modified after free" issue when fxp(4)
is running as a member of if_bridge(4).
Tested by: Larry Baird <lab <> gta dot com>
MFC after: 5 days
- Drop bogus quad_t cast for di_gen, it is a 32bit type
- Print di_gen with leading zeros, to get consistent output
Before this change, amd64 would print:
ino 18 gen 616ca2bd
ino 19 gen ffffffff95c2a3ff
ino 20 gen 25c3a3d5
ino 21 gen 8dc1472
ino 22 gen 3797056b
ino 23 gen 1d47853a
ino 24 gen ffffffff82d26995
After the change
ino 18 gen 616ca2bd
ino 19 gen 95c2a3ff
ino 20 gen 25c3a3d5
ino 21 gen 08dc1472
ino 22 gen 3797056b
ino 23 gen 1d47853a
ino 24 gen 82d26995
PR: bin/139994 (sort of)
Reviewed by: mckusick
It includes the following changes:
- parallel reads in traversal code (Bug ID 6333409)
- faster traversal for zfs send (Bug ID 6418042)
- traversal code cleanup (Bug ID 6725675)
- fix for two scrub related bugs (Bug ID 6729696, 6730101)
- fix assertion in dbuf_verify (Bug ID 6752226)
- fix panic during zfs send with i/o errors (Bug ID 6577985)
- replace P2CROSS with P2BOUNDARY (Bug ID 6725680)
List of OpenSolaris Bug IDs:
6333409, 6418042, 6757112, 6725668, 6725675, 6725680,
6725698, 6729696, 6730101, 6752226, 6577985, 6755042
Approved by: pjd, delphij (mentor)
Obtained from: OpenSolaris (multiple Bug IDs)
MFC after: 1 week
from 2000 bytes to 20 Kbytes, which now matches the buffer size used for
NGM_BINARY2ASCII conversions.
The aim of this change is to allow for bigger binary structures to be
managed via netgraph ASCII messages, until we come up with an API
improvement which would get rid of such arbitrary hardcoded limits.
MFC after: 3 days
bottom of the manpages and order them consistently.
GNU groff doesn't care about the ordering, and doesn't even mention
CAVEATS and SECURITY CONSIDERATIONS as common sections and where to put
them.
Found by: mdocml lint run
Reviewed by: ru
