that requires 10ms delay after device reset. Because that code was
there from day 1, I guess it was added to give enough settlement
time after updating BGE_MAC_MODE register.
The recommended delay time for BGE_MAC_MODE after updating is 40us
and it was already done in r241219.
The VCPU(Virtual CPU) of BCM5906 is used to provide a mechanism to
control the bootcode execution and to pick up configuration data
stored inside the EEPROM.
The bootcode of BCM5906 will check the BGE_VCPU_STATUS_DRV_RESET
bit to decide which booting procedure to choose.
Data sheet indicates the VCPU of BCM5906 should set
BGE_VCPU_STATUS_DRV_RESET bit *before* VCPU reset or global reset.
water mark to 256 bytes. Otherwise controller will encounter DMA
write under run errors and would result in RX DMA hang. If the
maximum payload size is 128 bytes, the water mark is set to 128
bytes as usual.
While here, set maximum read request size to 2048 for BCM5719/BCM5720.
For other PCIe devices, use 4096. And reprogram the maximum read
request size whenever device reset is performed.
make analog input loopback and dual-stream playback work by enabling
signal mixing by nid 22, as it should be according to info returned by
the CODEC. Otherwise pin nid 28 receives only signal from DAC nid 16.
PR: kern/169124
MFC after: 1 week
instruction loads/stores at its will.
The macro __compiler_membar() is currently supported for both gcc and
clang, but kernel compilation will fail otherwise.
Reviewed by: bde, kib
Discussed with: dim, theraven
MFC after: 2 weeks
r234247.
Use, instead, the static intializer introduced in r239923 for x86 and
sparc64 intr_cpus, unwinding the code to the initial version.
Reviewed by: marius
executed to better differentiate between loader-specific errors and kernel-
specific errors (if ever any of either).
This type of functionality hasn't been required before the introduction of the
advanced menu system (r222417). Adding this functionality will help different-
iate errors at the loader-level such as a BTX halt caused by heap exhaustion
and errors that may be involved with executing the kernel (wrong architecture
for example). A user can learn that messages before "Booting..." are related to
the loader(8) environment and it's Forth-ilk, while those after are not
related to loader(8) -- the point that loader(8) has ``left the building''.
This patch also includes a man-page update to color.4th(8) as the color logic
moves to a lower-level (from being included by beastie.4th to being included
by loader.4th).
After noticing a delay between execution of the overloaded "boot" FICL word and
the display of text on-screen, gcooper confirmed that the introduction of a
builtin memory test (disabled by adding hw.memtest.tests="0" to loader.conf(5))
was the cause of the delay.
This patch adds an echo to produce "Booting..." when the overloaded "boot" word
is executed (this includes from the interactive command-prompt on all arches,
from the menu system on arches that run the beastie menu, and even those arches
that run the menu but disable it by setting beastie_disable="YES" in
loader.conf(5)). When loader_color="YES" in loader.conf(5), the same message is
produced but in white text on a blue background (only the letters produced have
this background -- opposed to perhaps the entire line).
upon pmap_enter() to create a mapping within a different address space,
i.e., not the thread's own address space. On i386, this entails the
creation of a temporary mapping to the affected page table page (PTP). In
general, pmap_enter() will read from this PTP, allocate a PV entry, and
write to this PTP. The trouble comes when the system is short of memory.
In order to allocate a new PV entry, an older PV entry has to be
reclaimed. Reclaiming a PV entry involves destroying a mapping, which
requires access to the affected PTP. Thus, the PTP mapped at the
beginning of pmap_enter() is no longer mapped at the end of pmap_enter(),
which leads to pmap_enter() modifying the wrong PTP. To address this
problem, pmap_pv_reclaim() is changed to use an alternate method of
mapping PTPs.
Update a related comment.
Reported by: pho
Diagnosed by: kib
MFC after: 5 days
host byte order, was sometimes called with net byte order. Since we are
moving towards net byte order throughout the stack, the function was
converted to expect net byte order, and its consumers fixed appropriately:
- ip_output(), ipfilter(4) not changed, since already call
in_delayed_cksum() with header in net byte order.
- divert(4), ng_nat(4), ipfw_nat(4) now don't need to swap byte order
there and back.
- mrouting code and IPv6 ipsec now need to switch byte order there and
back, but I hope, this is temporary solution.
- In ipsec(4) shifted switch to net byte order prior to in_delayed_cksum().
- pf_route() catches up on r241245 changes to ip_output().
the ATH_TXQ_* macros.
* Introduce the new macros;
* rename the TID queue and TID filtered frame queue so the compiler
tells me I'm using the wrong macro.
These should correspond 1:1 to the existing code.
provider name to be specified instead of geom name (first argument in all
subcommands except label). In most cases there is only one array used
any way, so it is not really useful to make user type ugly geom names like
Intel-f0bdf223 or SiI-732c2b9448cf. Though they can be used in some cases.
Sponsored by: iXsystems, Inc.
MFC after: 1 month
range-based invalidation function instead of performing per-page
invalidations. Don't bother invalidating mappings that don't have PTE_D
set, since they don't allow write access.
processors, either on reboot or after power down with battery backup.
However, the AT91RM9200 RTC always resets on reboot making it just
about useless at the moment (if we support a low-power mode or an
extended sleep mode, it might become useful).
Submitted by: Ian Lepore
- clear capability flags when hw timeouts
- retire comc_started status variable and directly use c_flags to see
if comconsole is selected for use
Reviewed by: jhb
Tested by: Uffe Jakobsen <uffe@uffe.org>,
Olivier Cochard-Labbe <olivier@cochard.me>
MFC after: 26 days
- clarify meaning of console flags
- perform i/o via a console only if both of the following conditions are met:
o console is active (selected by user or config)
o console flags that it can perform the operation
- warn if a chosen console can not work (the warning may go nowhere without
working and active console, though)
Reviewed by: jhb
Tested by: Uffe Jakobsen <uffe@uffe.org>,
Olivier Cochard-Labbe' <olivier@cochard.me>
MFC after: 26 days
... instead of deferring the action until first open.
Unlike upstream this has no benefit on FreeBSD.
We know that as soon as the provider is created it is going to be tasted
and thus opened. Initial mediasize of zero causes tasting failure
and subsequent retasting because of the size change.
MFC after: 14 days
The first discovered pool, whether it covers the whole boot disk or not,
is going to be first in zfs_pools list. So there is no need at all
for spapp parameter.
This commit also fixes a bug where NULL would be assigned to NULL
pointer when probe_drive was called with the spapp parameter of NULL.
MFC after: 21 days
the temporary mappings that are used to implement operations like
pmap_zero_page(). There is no reason for the MIPS pmap to deviate
from that practice.
