but the use of fseek() means fetch(1) can't correctly resume a transfer
that was interrupted past the 2 GB mark.
Pointed out by: ache@
MFC after: 3 weeks
in append mode. Open it in read-write mode instead. Also move the
fseek up one level to cover the (unlikely but not impossible) case where
the server accepts ranges but does not send a Content-Size header.
PR: bin/117277
MFC after: 3 weeks
When a status pointer is passed in mfi_dcmd_command does not return an
errno (if the ioctl is successful), so move the test for NO_HW_PRESENT
outside of the error case. This should fix incorrect reporting for
systems with a dead or no battery.
Additionally, handle error codes other than NO_HW_PRESENT by omitting
the battery capacity display. LSI's supercap-based parts (CV series)
report their data using the same interface as battery-based parts,
except that they do not include the capacity stats (state of charge,
cumulative charge cycles, etc.)
Reviewd by: jhb, bz
Tested by: pluknet@, Garrett Cooper
PR: bin/160581
MFC after: 1 week
wdog_kern_pat() acquires eventhandler mutex, thus it cannot work in
kernel context (from where kdb_trap() runs).
The right way to fix this is both offering the
cpu-stop-on-panic-and-skip-locking logic and also a context for KDB
to officially run. We can re-enable this (or a similar) improvement
when these 2 patches hit the tree.
Sponsored by: Sandvine Incorporated
Discussed with: emaste, rstone
MFC after: immediately
build the ip_fw_pfil.c hooks and ipfw even in case of no-ip under the
assumption that the private L2 hook (which hopefully eventually will be a
pfil hook as well) can still be useful.
Allow building the module without inet as well.
Glanced at by: jhb
MFC after: 3 days
syscall exit path. Otherwise, if SIGTRAP is ignored, that tdsendsignal()
do not want to deliver the signal, and debugger never get a notification
of exec.
Found and tested by: Anton Yuzhaninov <citrin citrin ru>
Discussed with: jhb
MFC after: 2 weeks
kerberos libraries were not linked properly (missing dependencies),
which causes 3rd party applications linking to fail when --as-needed
ld flag is used. I also added the --no-undefined ld(1) flag to make
sure that there're no missing dependencies.
MFC after: 3 days
back-end features.
sys/dev/xen/netfront/netfront.c:
o Add xn_query_features() which reads the XenStore and
records the TSO, LRO, and chained ring-request support
of the backend.
o Rename xn_configure_lro() to xn_configure_features() and
use this routine to manage the setup of TSO, LRO, and
checksum offload.
o In create_netdev(), initialize if_capabilities and
if_hwassist to the capabilities found on all backends.
Delegate configuration of if_capenable and the TSO flag
if if_hwassist to xn_configure_features().
Reported by: Hugo Silva (fix inspired by patch provided)
Approved by: re
MFC after: 1 week
PV devices with the ioemu attribute set.
sys/dev/xen/netfront/netfront.c:
o If a mac address for the interface cannot be found
in the front-side XenStore tree, look for an entry
in the back-side tree. With ioemu devices, the
emulator does not populate the front side tree and
neither does Xend.
o Return an error rather than panic when an attach
attempt fails.
Reported by: Janne Snabb (fix inspired by patch provided)
PR: kern/154302
Approved by: re
Sponsored by: BQ Internet
sys/dev/xen/netfront/netfront.c:
o Implement netfront_suspend(), a specialized suspend
handler for the netfront driver. This routine simply
disables the carrier so the driver is idle during
system suspend processing.
o Fix a leak when re-initializing LRO during a link reset.
o In netif_release_tx_bufs(), when cleaning up the grant
references for our TX ring, use gnttab_end_foreign_access_ref
instead of attempting to grant the page again.
o In netif_release_tx_bufs(), we do not track mbufs associated
with mbuf chains, but instead just free each mbuf directly.
Use m_free(), not m_freem(), to avoid double frees of mbufs.
o Refactor some code to enhance clarity.
Approved by: re
MFC after: 1 week
sys/dev/xen/control/control.c:
Fix locking violations in Xen HVM suspend processing
and have it perform similar actions to those performed
during an ACPI triggered suspend.
Sponsored by: BQ Internet
Approved by: re
MFC after: 1 week
Sponsored by: BQ Internet
sys/dev/xen/blkfront/block.h:
sys/dev/xen/blkfront/blkfront.c:
Remove now unused blkif_vdev_t from the blkfront soft.
sys/dev/xen/blkfront/blkfront.c:
o In blkfront_suspend(), indicate the desire to suspend
by changing the softc connected state to SUSPENDED, and
then wait for any I/O pending on the remote peer to
drain. Cancel suspend processing if I/O does not
drain within 30 seconds.
o Enable and update blkfront_resume(). Since I/O is
drained prior to the suspension of the VM, the complicated
recovery process performed by other Xen blkfront
implementations is avoided. We simply tear down the
connection to our old peer, and then re-connect.
o In blkif_initialize(), fix a resource leak and botched
return if we cannot allocate shadow memory for our
requests.
o In blkfront_backend_changed(), correct our response to
the XenbusStateInitialised state. This state indicates
that our backend peer has published sufficient data for
blkfront to publish ring information and other XenStore
data, not that a connection can occur. Blkfront now
will only perform connection processing in response to
the XenbusStateConnected state. This corrects an issue
where blkfront connected before the backend was ready
during resume processing.
Approved by: re
MFC after: 1 week
framework.
Sponsored by: BQ Internet
sys/xen/xenbus/xenbusb.c:
o In xenbusb_resume(), publish the state transition of the
resuming device into XenbusStateIntiailising so that the
remote peer can see it. Recording the state locally is
not sufficient to trigger a re-connect sequence.
o In xenbusb_resume(), defer new-bus resume processing until
after the remote peer's XenStore address has been updated.
The drivers may need to refer to this information during
resume processing.
sys/xen/xenbus/xenbusb_back.c:
sys/xen/xenbus/xenbusb_front.c:
Register xenbusb_resume() rather than bus_generic_resume()
as the handler for device_resume events.
sys/xen/xenstore/xenstore.c:
o Fix grammer in a comment.
o In xs_suspend(), pass suspend events on to the child
devices (e.g. xenbusb_front/back, that are attached
to the XenStore.
Approved by: re
MFC after: 1 week
executable) after r190885. The whole region for the dso is mmaped with
MAP_NOCORE flag, doing only mprotect(2) over .bss prevented it from
writing .bss to core files.
Revert the optimization of using mprotect(2) to establish .bss, overlap
the section with mmap(2).
Reported by: attilio
Reviewed by: attilio, emaste
Approved by: re (bz)
MFC after: 2 weeks
This change fixes a race in device side mode during clear-stall from
host, which can cause data to be sent too early on the given
endpoint.
Approved by: re (kib)
MFC after: 1 week
clean-up RA messages for shutting down. The RA timers could prevent the rtadvd
daemon from shutting down because ra_output() just ignored !IFF_UP interfaces
and TRANSITIVE->UNCONFIGURED state transition never happened due to it.
Spotted by: kib
Approved by: re (bz)
conversion, conversion must fail and errno must be set to E2BIG.
PR: standards/160673
Submitted by: Henning Petersen <henning.petersen@t-online.de>
Reviewed by: pluknet
Approved by: re (kib), delphij (mentor)
thing all the other architectures already do) thus just initialize
kernel_pmap in pmap_bootstrap().
Reported by: alc
Reviewed by: alc, marius
Tested by: flo, marius
Approved by: re (kib)
MFC after: 1 week
- Emphasize $ipv6_enable and $ipv6_prefer are deprecated.
- Add more detail descriptions about $ipv6_activate_all_interfaces.
- Add some more examples of $ifconfig_IF_ipv6.
- rtsold(8) and rtadvd(8) can be used even when ipv6_gateway_enable=NO now.
Approved by: re (kib)
Improve exit when an error occurs.
Fix parsing to grab values which contain extra '=' signs.
Fix a bug setting the timezone properly.
Fix a usage bug when setting up with gmirror.
Allow a uzip file from local media to be used.
Allow specifying flags for "newfs" when using UFS as the file system.
Run custom commands after doing final cleanup / fstab generation
and such. Also fix using relative path for config file.
Approved by: re (bz)
