using 512 byte blocks).
cam_ccb.h: Bump up volume_size and cylinders in ccb_calc_geometry to
64 bits and 32 bits respectively, so we can hold larger
device sizes. cylinders would overflow at about 500GB.
Bump CAM_VERSION for this change. Note that this will
require a recompile of all applications that talk to the
pass(4) driver.
scsi_all.c: Add descriptions for READ/WRITE(16), update READ/WRITE(12)
descriptions, add descriptions for SERVICE ACTION IN/OUT.
Add a new function, scsi_read_capacity_16(), that issues
the read capacity service action. (Necessary for arrays
larger than 2^32 sectors.) Update scsi_read_write() to use
a 64 bit LBA and issue READ(16) or WRITE(16) if necessary.
NOTE the API change. This should be largely transparnet
to most userland applications at compile time, but will
break binary compatibility. The CAM_VERSION bump, above,
also serves the purpose of forcing a recompile for any
applications that talk to CAM.
scsi_all.h: Add 16 byte READ/WRITE structures, structures for 16 byte
READ CAPACITY/SERVICE ACTION IN. Add scsi_u64to8b() and
scsi_8btou64.
scsi_da.c: The da(4) driver probe now has two stages for devices
larger than 2TB. If a standard READ CAPACITY(10) returns
0xffffffff, we issue the 16 byte version of read capacity
to determine the true array capacity. We also do the same
thing in daopen() -- use the 16 byte read capacity if the
device is large enough.
The sysctl/loader code has also been updated to accept
16 bytes as a minimum command size.
Casio QV-R3 USB camera, which appears to use a Pentax chipset
M-Systems DiskOnKey USB flash key
Feiya "slider" dual-slot flash reader
SmartDisk (Mitsumi) USB floppy drive
PR: kern/46545, kern/47793, kern/50020, kern/50226
Retain the mistake of not updating the devstat API for now.
Spell bioq_disksort() consistently with the remaining bioq_*().
#include <geom/geom_disk.h> where this is more appropriate.
cdcleanup(). This fixes sysctl problems ("can't re-use a leaf") when
someone adds another peripheral at the same unit number. (e.g. rescan da0,
it goes away, then rescan again and da0 comes back, but since we haven't
cleaned up the sysctl variables from the last da0 instance, we can't
register the variables for the new instance under the same name.)
Reported by: njl
Tested by: njl
Kernel:
Change statistics to use the *uptime() timescale (ie: relative to
boottime) rather than the UTC aligned timescale. This makes the
device statistics code oblivious to clock steps.
Change timestamps to bintime format, they are cheaper.
Remove the "busy_count", and replace it with two counter fields:
"start_count" and "end_count", which are updated in the down and
up paths respectively. This removes the locking constraint on
devstat.
Add a timestamp argument to devstat_start_transaction(), this will
normally be a timestamp set by the *_bio() function in bp->bio_t0.
Use this field to calculate duration of I/O operations.
Add two timestamp arguments to devstat_end_transaction(), one is
the current time, a NULL pointer means "take timestamp yourself",
the other is the timestamp of when this transaction started (see
above).
Change calculation of busy_time to operate on "the salami principle":
Only when we are idle, which we can determine by the start+end
counts being identical, do we update the "busy_from" field in the
down path. In the up path we accumulate the timeslice in busy_time
and update busy_from.
Change the byte_* and num_* fields into two arrays: bytes[] and
operations[].
Userland:
Change the misleading "busy_time" name to be called "snap_time" and
make the time long double since that is what most users need anyway,
fill it using clock_gettime(CLOCK_MONOTONIC) to put it on the same
timescale as the kernel fields.
Change devstat_compute_etime() to operate on struct bintime.
Remove the version 2 legacy interface: the change to bintime makes
compatibility far too expensive.
Fix a bug in systat's "vm" page where boot relative busy times would
be bogus.
Bump __FreeBSD_version to 500107
Review & Collaboration by: ken
use the underlying AsahiOptical USB chip and thus this quirk may need to
be generalized in the future.
PR: kern/46369
Submitted by: Tim Vanderhoek <vanderh@ecf.utoronto.ca>
MFC After: 3 days
in geom_disk.c.
As a side effect this makes a lot of #include <sys/devicestat.h>
lines not needed and some biofinish() calls can be reduced to
biodone() again.
branches:
Initialize struct cdevsw using C99 sparse initializtion and remove
all initializations to default values.
This patch is automatically generated and has been tested by compiling
LINT with all the fields in struct cdevsw in reverse order on alpha,
sparc64 and i386.
Approved by: re(scottl)
Retire the "d_dump_t" and use the "dumper_t" type instead.
Dumper_t takes a void * as first arg which is more general than the
dev_t taken by d_dump_t. (Remember: we could have net-dumpers if
somebody wrote us one!)
Define the convention for GEOM controlled disk devices to be that the
first argument to the dumper function is the struct disk pointer.
Change device drivers accordingly.
Change the argument to disk_destroy() to be the same struct disk * as
disk_create() takes.
This enables drivers to ignore the (now) bogus dev_t which disk_create()
returns.
a number of related problems along the way.
- Automatically detect CDROM drives that can't handle 6 byte mode
sense and mode select, and adjust our command size accordingly.
We have to handle this in the cd(4) driver (where the buffers are
allocated), since the parameter list length is different for the
6 and 10 byte mode sense commands.
- Remove MODE_SENSE and MODE_SELECT translation removed in ATAPICAM
and in the umass(4) driver, since there's no way for that to work
properly.
- Add a quirk entry for CDROM drives that just hang when they get a 6
byte mode sense or mode select. The reason for the quirk must be
documented in a PR, and all quirks must be approved by
ken@FreeBSD.org. This is to make sure that we fully understand why
each quirk is needed. Once the CAM_NEW_TRAN_CODE is finished, we
should be able to remove any such quirks, since we'll know what
protocol the drive speaks (SCSI, ATAPI, etc.) and therefore whether
we should use 6 or 10 byte mode sense/select commands.
- Change the way the da(4) handles the no_6_byte sysctl. There is
now a per-drive sysctl to set the minimum command size for that
particular disk. (Since you could have multiple disks with
multiple requirements in one system.)
- Loader tunable support for all the sysctls in the da(4) and cd(4)
drivers.
- Add a CDIOCCLOSE ioctl for cd(4) (bde pointed this out a long
time ago).
- Add a media validation routine (cdcheckmedia()) to the cd(4)
driver, to fix some problems bde pointed out a long time ago. We
now allow open() to succeed no matter what, but if we don't detect
valid media, the user can only issue CDIOCCLOSE or CDIOCEJECT
ioctls.
- The media validation routine also reads the table of contents off
the drive. We use the table of contents to implement the
CDIOCPLAYTRACKS ioctl using the PLAY AUDIO MSF command. The
PLAY AUDIO TRACK INDEX command that we previously used was
deprecated after SCSI-2. It works in every SCSI CDROM I've tried,
but doesn't seem to work on ATAPI CDROM drives. We still use the
play audio track index command if we don't have a valid TOC, but
I suppose it'll fail anyway in that case.
- Add _len() versions of scsi_mode_sense() and scsi_mode_select() so
that we can specify the minimum command length.
- Fix a couple of formatting problems in the sense printing code.
MFC after: 4 weeks
* Fix a bug where devices weren't cleaned up on close(): CAM_REQ_CMP != 0
user:
* Increase timeout in usermode to CAM_TIME_INFINITY. The initiator is in
charge of timeouts and the value was in ms, not seconds.
* Bring two debugging printfs under the debug flag
* Clean up man page to show increased testing on isp(4)
Submitted by: gibbs (bugfixes)
Otherwise, the scsi devices that it is trying to issue commands to may
have gone away. This is what caused shutdown to hang on ia64 systems
with mpt scsi controllers. The bus system has torn down the device tree
and reset the mpt controller etc, and suddenly along comes dashutdown
and wants to issue a few more scsi commands.... <HANG!>
This shouldn't work on i386 either, but it seems to work solely due
to luck.
But for some reason the block size is different when a different type of
tape is placed in the drive. This commit fixes that.
PR: 46209
Submitted by: Alex Wang <alex@alexwang.com>
Approved by: mjacob
That reference is to be held only if daopen() has been successful
and until daclose() releases it. daclose() won't be called if
daopen() has failed, though.
Approved by: re, njl
MFC after: 1 week
If the value from the user is less than 177, assume it is a multiple of
a single speed CDROM and convert to KB/sec.
No complaints from: sos
Reviewed by: ken
Approved by: re
MFC after: 1 day
This code allows a user program to enable target mode on a SIM and
then emulate any number of devices (disks, tape drives, etc.) All
decisions about device behavior (UA, CA, inquiry response) are left
to the usermode program and the kernel driver is merely a conduit
for CCBs. This enables multiple concurrent target emulators, each
using its own backing store and IO model.
Also included is a user program that emulates a disk (RBC) using a
file as a backing store. This provides functionality similar to
md(4) at the CAM layer.
Code has been tested on ahc(4) and should also work on isp(4) (and
other SIMs that gain target mode support). It is a complete rewrite
of /sys/cam/scsi_target* and /usr/share/examples/scsi_target.
Design, comments from: gibbs
Supported by: Cryptography Research
Approved by: re
* Change atapi-cd ioctls to use the same units.
* Change burncd, cdcontrol to convert CDROM speed to KB/sec before
calling the ioctl. Add a "max" speed option for their command lines.
This change does not break ABI but does change the units passed through
the ioctl so 3rd party software that uses cdrio.h will have to convert
(most likely by multiplying CDROM speed by 177 to get KB/s).
PR: kern/36845
Submitted by: Philipp Mergenthaler <p@i609a.hadiko.de> (CAM ioctls)
Reviewed by: sos, ken
MFC after: 1 month
