ever connect a SCSI Cdrom/Tape/Jukebox/Scanner/Printer/kitty-litter-scooper
to your high-end RAID controller. The interface to the arrays is still
via the block interface; this merely provides a way to circumvent the
RAID functionality and access the SCSI buses directly. Note that for
somewhat obvious reasons, hard drives are not exposed to the da driver
through this interface, though you can still talk to them via the pass
driver. Be the first on your block to low-level format unsuspecting
drives that are part of an array!
To enable this, add the 'aacp' device to your kernel config.
MFC after: 3 days
timecounter will be used starting at the next second, which is
good enough for sysctl purposes. If better adjustment is needed
the NTP PLL should be used.
the symbol index defined by the relocation. The elf_lookup() support
function is to be used by elf_reloc() when symbol lookups need to be
done. The elf_lookup() function operates on the symbol index and
will do a symbol name based lookup when such is required, otherwise
it uses the symbol index directly. This solves the problem seen on
ia64 where the symbol hash table does not contain local symbols and
a symbol name based lookup would fail for those symbols.
Don't pass the symbol name to elf_reloc(), as it isn't used any more.
2, but that's not the case. This fixes the case where there were slots
in the PIR table that had no bits set, but we assumed they did and used
strange results as a result.
o Map invalid INTLINE registers to 255 in pci_cfgreg.c. This should allow
us to remove the bogus checks in MI code for non-255 values.
I put these changes out for review a while ago, but no one responded
to them, so into current they go.
This should help us work better on machines that don't route
interrupts in the traditional way.
MFC After: 4286 millifortnights
due to conditions that suggest the possible need for stack growth.
This has two beneficial effects: (1) we can
now remove calls to vm_map_growstack() from the MD trap handlers and (2)
simple page faults are faster because we no longer unnecessarily perform
vm_map_growstack() on every page fault.
o Remove vm_map_growstack() from the i386's trap_pfault().
o Remove the acquisition and release of Giant from i386's trap_pfault().
(vm_fault() still acquires it.)
environment needed at boot time to a dynamic subsystem when VM is
up. The dynamic kernel environment is protected by an sx lock.
This adds some new functions to manipulate the kernel environment :
freeenv(), setenv(), unsetenv() and testenv(). freeenv() has to be
called after every getenv() when you have finished using the string.
testenv() only tests if an environment variable is present, and
doesn't require a freeenv() call. setenv() and unsetenv() are self
explanatory.
The kenv(2) syscall exports these new functionalities to userland,
mainly for kenv(1).
Reviewed by: peter
and pmap_copy_page(). This gets rid of a couple more physical addresses
in upper layers, with the eventual aim of supporting PAE and dealing with
the physical addressing mostly within pmap. (We will need either 64 bit
physical addresses or page indexes, possibly both depending on the
circumstances. Leaving this to pmap itself gives more flexibilitly.)
Reviewed by: jake
Tested on: i386, ia64 and (I believe) sparc64. (my alpha was hosed)
trying to run X on some Athlon systems where the BIOS does odd things
(mines an ASUS A7A266, but it seems to also help on other systems).
Here's a description of the problem and my fix:
The problem with the old MTRR code is that it only expects
to find documented values in the bytes of MTRR registers.
To convert the MTRR byte into a FreeBSD "Memory Range Type"
(mrt) it uses the byte value and looks it up in an array.
If the value is not in range then the mrt value ends up
containing random junk.
This isn't an immediate problem. The mrt value is only used
later when rewriting the MTRR registers. When we finally
go to write a value back again, the function i686_mtrrtype()
searches for the junk value and returns -1 when it fails
to find it. This is converted to a byte (0xff) and written
back to the register, causing a GPF as 0xff is an illegal
value for a MTRR byte.
To work around this problem I've added a new mrt flag
MDF_UNKNOWN. We set this when we read a MTRR byte which
we do not understand. If we try to convert a MDF_UNKNOWN
back into a MTRR value, then the new function, i686_mrt2mtrr,
just returns the old value of the MTRR byte. This leaves
the memory range type unchanged.
I'd like to merge this before the 4.6 code freeze, so if people
can test this with XFree 4 that would be very useful.
PR: 28418, 25958
Tested by: jkh, Christopher Masto <chris@netmonger.net>
MFC after: 2 weeks
the indentation more like the other multi-line assembley in
this file.
Someone who understands gcc constraints could update the
constraints for do_cpuid.
o Recent changes to osigreturn() and sigreturn() have made them MPSAFE. Add
a comment to this effect.
Submitted by: bde (bullet #1)
Reviewed by: jhb (bullet #2)
without a few patches for the rest of the kernel to allow the image
activator to override exec_copyout_strings and setregs.
None of the syscall argument translation has been done. Possibly, this
translation layer can be shared with any platform that wants to support
running ILP32 binaries on an LP64 host (e.g. sparc32 binaries?)
PCPU_LAZY_INC() which increments elements in it for cases where we
can afford the occassional inaccuracy. Use of per-cpu stats counters
avoids significant cache stalls in various critical paths that would
otherwise severely limit our cpu scaleability.
Adjust all sysctl's accessing cnt.* elements to now use a procedure
which aggregates the requested field for all cpus and for the global
vmmeter.
The global vmmeter is retained, since some stats counters, like v_free_min,
cannot be made per-cpu. Also, this allows us to convert counters from
the global vmmeter to the per-cpu vmmeter in a piecemeal fashion, so
have at it!
most cases NULL is passed, but in some cases such as network driver locks
(which use the MTX_NETWORK_LOCK macro) and UMA zone locks, a name is used.
Tested on: i386, alpha, sparc64
In the i386 case, options BOOTP requires options NFS_ROOT as well as
options NFSCLIENT. With *both* the NFS options, a bootpc_init()
prototype is brought in by nfsclient/nfsdiskless.h.
In the ia64 case, it just doesn't work and my change just pushes it
further away from working.
Suggested to be wrong by: bde
they aren't in the usual path of execution for syscalls and traps.
The main complication for this is that we have to set flags to control
ast() everywhere that changes the signal mask.
Avoid locking in userret() in most of the remaining cases.
Submitted by: luoqi (first part only, long ago, reorganized by me)
Reminded by: dillon
Unfortunately, this level doesn't really provide enough granularity. We
probably need several MI NOTES type files for things that are shared by
several architectures but not by all. For example, the PCI options could
live in a NOTES.pci.
This also updates the Makefile for i386 to generate LINT. The only changes
in the generated LINT are the order of various options.
Suggestions for improvement welcome.
in dump byte order (=network byte order). Swap blocksize and dumptime
to avoid extraneous padding on 64-bit architectures. Use CTASSERT
instead of runtime checks to make sure the header is 512 bytes large.
Various style(9) fixes.
Reviewed by: phk, bde, mike
various machdep.c's to being declared in kern_mutex.c.
- Add a new function mutex_init() used to perform early initialization
needed for mutexes such as setting up thread0's contested lock list
and initializing MI mutexes. Change the various MD startup routines
to call this function instead of duplicating all the code themselves.
Tested on: alpha, i386
and cpu_critical_exit() and moves associated critical prototypes into their
own header file, <arch>/<arch>/critical.h, which is only included by the
three MI source files that need it.
Backout and re-apply improperly comitted syntactical cleanups made to files
that were still under active development. Backout improperly comitted program
structure changes that moved localized declarations to the top of two
procedures. Partially re-apply one of the program structure changes to
move 'mask' into an intermediate block rather then in three separate
sub-blocks to make the code more readable. Re-integrate bug fixes that Jake
made to the sparc64 code.
Note: In general, developers should not gratuitously move declarations out
of sub-blocks. They are where they are for reasons of structure, grouping,
readability, compiler-localizability, and to avoid developer-introduced bugs
similar to several found in recent years in the VFS and VM code.
Reviewed by: jake
general cleanup of the API. The entire API now consists of two functions
similar to the pre-KSE API. The suser() function takes a thread pointer
as its only argument. The td_ucred member of this thread must be valid
so the only valid thread pointers are curthread and a few kernel threads
such as thread0. The suser_cred() function takes a pointer to a struct
ucred as its first argument and an integer flag as its second argument.
The flag is currently only used for the PRISON_ROOT flag.
Discussed on: smp@
Caveats:
The new savecore program is not complete in the sense that it emulates
enough of the old savecores features to do the job, but implements none
of the options yet.
I would appreciate if a userland hacker could help me out getting savecore
to do what we want it to do from a users point of view, compression,
email-notification, space reservation etc etc. (send me email if
you are interested).
Currently, savecore will scan all devices marked as "swap" or "dump" in
/etc/fstab _or_ any devices specified on the command-line.
All architectures but i386 lack an implementation of dumpsys(), but
looking at the i386 version it should be trivial for anybody familiar
with the platform(s) to provide this function.
Documentation is quite sparse at this time, more to come.
Details:
ATA and SCSI drivers should work as the dump formatting code has been
removed. The IDA, TWE and AAC have not yet been converted.
Dumpon now opens the device and uses ioctl(DIOCGKERNELDUMP) to set
the device as dumpdev. To implement the "off" argument, /dev/null
is used as the device.
Savecore will fail if handed any options since they are not (yet)
implemented. All devices marked "dump" or "swap" in /etc/fstab
will be scanned and dumps found will be saved to diskfiles
named from the MD5 hash of the header record. The header record
is dumped in readable format in the .info file. The kernel
is not saved. Only complete dumps will be saved.
All maintainer rights for this code are disclaimed: feel free to
improve and extend.
Sponsored by: DARPA, NAI Labs
the osigcontext or ucontext_t rather than useracc() followed by direct user-
space memory accesses. This reduces (o)sigreturn()'s execution time by 5-
50%.
Submitted by: bde
with this flag. Remove the dup_list and dup_ok code from subr_witness. Now
we just check for the flag instead of doing string compares.
Also, switch the process lock, process group lock, and uma per cpu locks over
to this interface. The original mechanism did not work well for uma because
per cpu lock names are unique to each zone.
Approved by: jhb
disablement assumptions in kern_fork.c by adding another API call,
cpu_critical_fork_exit(). Cleanup the td_savecrit field by moving it
from MI to MD. Temporarily move cpu_critical*() from <arch>/include/cpufunc.h
to <arch>/<arch>/critical.c (stage-2 will clean this up).
Implement interrupt deferral for i386 that allows interrupts to remain
enabled inside critical sections. This also fixes an IPI interlock bug,
and requires uses of icu_lock to be enclosed in a true interrupt disablement.
This is the stage-1 commit. Stage-2 will occur after stage-1 has stabilized,
and will move cpu_critical*() into its own header file(s) + other things.
This commit may break non-i386 architectures in trivial ways. This should
be temporary.
Reviewed by: core
Approved by: core
not removing tabs before "__P((", and not outdenting continuation lines
to preserve non-KNF lining up of code with parentheses. Switch to KNF
formatting and/or rewrap the whole prototype in some cases.
not removing tabs before "__P((", and not outdenting continuation lines
to preserve non-KNF lining up of code with parentheses. Switch to KNF
formatting and/or rewrap the whole prototype in some cases.
not removing tabs before "__P((", and not outdenting continuation lines
to preserve non-KNF lining up of code with parentheses. Switch to KNF
formatting and/or rewrap the whole prototype in some cases.
Instead of caching the ucred reference, just go ahead and eat the
decerement and increment of the refcount. Now that Giant is pushed down
into crfree(), we no longer have to get Giant in the common case. In the
case when we are actually free'ing the ucred, we would normally free it on
the next kernel entry, so the cost there is not new, just in a different
place. This also removse td_cache_ucred from struct thread. This is
still only done #ifdef DIAGNOSTIC.
Tested on: i386, alpha
to copy the sigframe to the user's stack. Useracc() takes a non-trivial
amount of time. Eliminating it speeds up signal delivery by 15% or more.
o Update some comments.
Submitted by: bde
older PCI BIOSes hate this and this leads to panics when it is done. Also,
assume that a uniquely routed interrupt is already routed. This also
seems to help some older laptops with feable BIOSes cope.
machdep.guessed_bootdev, and add code to sysctl to parse its value
and give a (not necessarily correct) name to the device we booted
from (the main motivation for this code is to use the info in the
PicoBSD boot scripts, and the impact on the kernel is minimal).
NOTE: the information available in bootdev is not always reliable,
so you should not trust it too much. The parsing code is the same
as in boot2.c, and cannot cover all cases -- as it is, it seems to
work fine with floppies and IDE disks recognised by the BIOS. It
_should_ work as well with SCSI disks recognised by the BIOS.
Booting from a CDROM in floppy emulation will return /dev/fd0 (because
this is what the BIOS tells us).
Booting off the network (e.g. with etherboot) leaves bootdev unset so
the value will be printed as "invalid (0xffffffff)".
Finally, this feature might go away at some point, hopefully when we
have a more reliable way to get the same information.
MFC-after: 5 days
be allocated as arrays indexed by the cpu id. Previously the only reliable
way to know the max cpu id was through MAXCPU. mp_ncpus isn't useful here
because cpu ids may be sparsely mapped, although x86 and alpha do not do this.
Also, call cpu_mp_probe much earlier so the max cpu id is known before the VM
starts up. This is intended to help support per cpu queues for the new
allocator, but may be useful elsewhere.
Reviewed by: jake
Approved by: jake
This makes other power-management system (APM for now) to be able to
generate power profile change events (ie. AC-line status changes), and
other kernel components, not only the ACPI components, can be notified
the events.
- move subroutines in acpi_powerprofile.c (removed) to kern/subr_power.c
- call power_profile_set_state() also from APM driver when AC-line
status changes
- add call-back function for Crusoe LongRun controlling on power
profile changes for a example
Previously, the UPAGES/KSTACK area of processes/threads would leak memory
at the time that a previously swapped process was terminated. Lukcily, the
leak was only 12K/proc, so it was unlikely to be a major problem unless you
had an undersized swap partition.
Submitted by: dillon
Reviewed by: silby
MFC after: 1 week
In order to determine what to page out, the vm_daemon checks
reference bits on all pages belonging to all processes. Unfortunately,
the algorithm used reacted badly with shared pages; each shared page
would be checked once per process sharing it; this caused an O(N^2)
growth of tlb invalidations. The algorithm has been changed so that
each page will be checked only 16 times.
Prior to this change, a fork/sleepbomb of 1300 processes could cause
the vm_daemon to take over 60 seconds to complete, effectively
freezing the system for that time period. With this change
in place, the vm_daemon completes in less than a second. Any system
with hundreds of processes sharing pages should benefit from this change.
Note that the vm_daemon is only run when the system is under extreme
memory pressure. It is likely that many people with loaded systems saw
no symptoms of this problem until they reached the point where swapping
began.
Special thanks go to dillon, peter, and Chuck Cranor, who helped me
get up to speed with vm internals.
PR: 33542, 20393
Reviewed by: dillon
MFC after: 1 week
device drivers for bus system with other endinesses than the CPU (using
interfaces compatible to NetBSD):
- bwap16() and bswap32(). These have optimized implementations on some
architectures; for those that don't, there exist generic implementations.
- macros to convert from a certain byte order to host byte order and vice
versa, using a naming scheme like le16toh(), htole16().
These are implemented using the bswap functions.
- stream bus space access functions, which do not perform a byte order
conversion (while the normal access functions would if the bus endianess
differs from the CPU endianess).
htons(), htonl(), ntohs() and ntohl() are implemented using the new
functions above for kernel usage. None of the above interfaces is currently
exported to user land.
Make use of the new functions in a few places where local implementations
of the same functionality existed.
Reviewed by: mike, bde
Tested on alpha by: mike
There is some unresolved badness that has been eluding me, particularly
affecting uniprocessor kernels. Turning off PG_G helped (which is a bad
sign) but didn't solve it entirely. Userland programs still crashed.
boot and run (and indeed I am committing from it) instead of exploding
during the int 0x15 call from inside the atkbd driver to get the keyboard
repeat rates.
shootdowns in a couple of key places. Do the same for i386. This also
hides some physical addresses from higher levels and has it use the
generic vm_page_t's instead. This will help for PAE down the road.
Obtained from: jake (MI code, suggestions for MD part)
enabled in critical sections and streamline critical_enter() and
critical_exit().
This commit allows an architecture to leave interrupts enabled inside
critical sections if it so wishes. Architectures that do not wish to do
this are not effected by this change.
This commit implements the feature for the I386 architecture and provides
a sysctl, debug.critical_mode, which defaults to 1 (use the feature). For
now you can turn the sysctl on and off at any time in order to test the
architectural changes or track down bugs.
This commit is just the first stage. Some areas of the code, specifically
the MACHINE_CRITICAL_ENTER #ifdef'd code, is strictly temporary and will
be cleaned up in the STAGE-2 commit when the critical_*() functions are
moved entirely into MD files.
The following changes have been made:
* critical_enter() and critical_exit() for I386 now simply increment
and decrement curthread->td_critnest. They no longer disable
hard interrupts. When critical_exit() decrements the counter to
0 it effectively calls a routine to deal with whatever interrupts
were deferred during the time the code was operating in a critical
section.
Other architectures are unaffected.
* fork_exit() has been conditionalized to remove MD assumptions for
the new code. Old code will still use the old MD assumptions
in regards to hard interrupt disablement. In STAGE-2 this will
be turned into a subroutine call into MD code rather then hardcoded
in MI code.
The new code places the burden of entering the critical section
in the trampoline code where it belongs.
* I386: interrupts are now enabled while we are in a critical section.
The interrupt vector code has been adjusted to deal with the fact.
If it detects that we are in a critical section it currently defers
the interrupt by adding the appropriate bit to an interrupt mask.
* In order to accomplish the deferral, icu_lock is required. This
is i386-specific. Thus icu_lock can only be obtained by mainline
i386 code while interrupts are hard disabled. This change has been
made.
* Because interrupts may or may not be hard disabled during a
context switch, cpu_switch() can no longer simply assume that
PSL_I will be in a consistent state. Therefore, it now saves and
restores eflags.
* FAST INTERRUPT PROVISION. Fast interrupts are currently deferred.
The intention is to eventually allow them to operate either while
we are in a critical section or, if we are able to restrict the
use of sched_lock, while we are not holding the sched_lock.
* ICU and APIC vector assembly for I386 cleaned up. The ICU code
has been cleaned up to match the APIC code in regards to format
and macro availability. Additionally, the code has been adjusted
to deal with deferred interrupts.
* Deferred interrupts use a per-cpu boolean int_pending, and
masks ipending, spending, and fpending. Being per-cpu variables
it is not currently necessary to lock; bus cycles modifying them.
Note that the same mechanism will enable preemption to be
incorporated as a true software interrupt without having to
further hack up the critical nesting code.
* Note: the old critical_enter() code in kern/kern_switch.c is
currently #ifdef to be compatible with both the old and new
methodology. In STAGE-2 it will be moved entirely to MD code.
Performance issues:
One of the purposes of this commit is to enhance critical section
performance, specifically to greatly reduce bus overhead to allow
the critical section code to be used to protect per-cpu caches.
These caches, such as Jeff's slab allocator work, can potentially
operate very quickly making the effective savings of the new
critical section code's performance very significant.
The second purpose of this commit is to allow architectures to
enable certain interrupts while in a critical section. Specifically,
the intention is to eventually allow certain FAST interrupts to
operate rather then defer.
The third purpose of this commit is to begin to clean up the
critical_enter()/critical_exit()/cpu_critical_enter()/
cpu_critical_exit() API which currently has serious cross pollution
in MI code (in fork_exit() and ast() for example).
The fourth purpose of this commit is to provide a framework that
allows kernel-preempting software interrupts to be implemented
cleanly. This is currently used for two forward interrupts in I386.
Other architectures will have the choice of using this infrastructure
or building the functionality directly into critical_enter()/
critical_exit().
Finally, this commit is designed to greatly improve the flexibility
of various architectures to manage critical section handling,
software interrupts, preemption, and other highly integrated
architecture-specific details.
on for a while:
- fine grained TLB shootdown for SMP on i386
- ranged TLB shootdowns.. eg: specify a range of pages to shoot down with
a single IPI, since the IPI is very expensive. Adjust some callers
that used to trigger this inside tight loops to do a ranged shootdown
at the end instead.
- PG_G support for SMP on i386 (options ENABLE_PG_G)
- defer PG_G activation till after we decide what we are going to do with
PSE and the 4MB pages at the start of the kernel. This should solve
some rumored strangeness about stale PG_G entries getting stuck
underneath the 4MB pages.
- add some instrumentation for the fine TLB shootdown
- convert some asm instruction wrappers from functions to inlines. gcc
seems to do a fair bit better with this.
- [temporarily!] pessimize the tlb shootdown IPI handlers. I will fix
this again shortly.
This has been working fairly well for me for a while, but I have tweaked
it again prior to commit since my last major testing round. The only
outstanding problem that I know of is PG_G related, which is why there
is an option for it (not on by default for SMP). I have seen a world
speedups by a few percent (as much as 4 or 5% in one case) but I have
*not* accurately measured this - I am a bit sceptical of these numbers.
While in userland, keep the thread's ucred reference in a shadow
field so that the usual place to store it is NULL.
If DIAGNOSTIC is not set, the thread ucred is kept valid until the next
kernel entry, at which time it is checked against the process cred
and possibly corrected. Produces a BIG speedup in
kernels with INVARIANTS set. (A previous commit corrected it
for the non INVARIANTS case already)
Reviewed by: dillon@freebsd.org
ucontext_t. Forward declare struct __ucontext in <sys/signal.h> and
remove reliance on <sys/ucontext.h> being included.
While I'm here, also hide osigcontext types from userland; suggested
by bde.
Namespace pollution noticed by: Kevin Day <toasty@shell.dragondata.com>
reaquiring it. In the same vein, don't bother dropping the thread cred
when goinf ot userland. We are guaranteed to nned it when we come back,
(which we are guaranteed to do).
Reviewed by: jhb@freebsd.org, bde@freebsd.org (slightly different version)
SMP we'd like as much feedback as possible from users about possible
locking problems as early as possible.
To negate most of the performance impact I've also enabled
WITNESS_SKIPSPIN. I've done this as we've been running WITNESS
over the spinlock code for a while without incident and it goes a
long way to making the performance problems of WITNESS much more
bearable.
Users who should be running current should know about turning WITNESS
off for performance reasons.
That said and done, WITNESS could/should be made into a tuneable,
but we'll leave that as an excersize to those that want to disable
it without a kernel recompile.
slower, and may be impeding adoption of -CURRENT by developers. We
recommend turning on WITNESS by default on crash boxes, and when doing
locking development. It will probably get turned on by default for a week
or two following any major locking commits, also.
Approved by: all and sundry (jhb, phk, ...)
feature bit on newer Athlon CPUs if the BIOS has forgotten to enable
it.
This patch was constructed using some info made available by John
Clemens at http://www.deater.net/john/PavilionN5430.html
Reviewed by: -audit
MFC after: 3 weeks
- Collected i486 identification codes in one place like
586 and 686.
- Merged two cases (0x470 and 0x490) for `Enhanced Am486DX4
Write-Back.'
- Replaced `unknown' into `Unknown'.
Submitted by: chi@bd.mbn.or.jp (Chiharu Shibata)
this is a low-functionality change that changes the kernel to access the main
thread of a process via the linked list of threads rather than
assuming that it is embedded in the process. It IS still embeded there
but remove all teh code that assumes that in preparation for the next commit
which will actually move it out.
Reviewed by: peter@freebsd.org, gallatin@cs.duke.edu, benno rice,
from old signal handlers. This is simpler and faster, and fixes (new)
sigreturn(2) when %eip in the new signal context happens to match the
magic value (0x1d516). 0x1d516 is below the default ELF text section,
so this probably never broken anything in practice.
locore.s:
In addition, don't build the signal trampoline for old signal handlers
when it is not used.
alpha:
Not fixed, but seems to be even less broken in practice due to more
advanced magic. A false match occurs for register #32 in mc_regs[].
Since there is no hardware register #32, a false match is only possible
for direct calls to sigreturn(2) that happen to have the magic number
in the spare mc_regs[32] field.
some arches and the syscall table is machine-independent. It was
(bogusly) conditional on COMPAT_43, so this usually makes no difference.
ia64: in addition:
- replace the bogus cloned comment before osigreturn() by a correct one.
osigreturn() is just a stub fo ia64's.
- fix the formatting of cloned comment before sigreturn().
- fix the return code. use nosys() instead of returning ENOSYS to get
the same semantics as if the syscall is not in the syscall table.
Generating SIGSYS is actually correct here.
- fix style bugs.
powerpc: copy the cleaned up ia64 stub. This mainly fixes a bogus comment.
sparc64: copy the cleaned up the ia64 stub, since there was no stub before.
for SMP in the plain profiling case. It seems to work too.
This error was not detected by LINT because LINT only compiles the
GUPROF profiling case, which is is a superset of the plain profiling
case for !SMP but which is so broken for SMP that the buggy code is
not compiled.
the packet transfer routines, since rev.1.468 of machdep.c does this
better. I'm surprised that disabling interrupts helped much. Disabling
them in the packet receive routine is too late.
Fixed some minor style bugs in rev.1.14.
to fetch the magic word instead of useracc() plus a direct access.
This is more efficient as well as simpler and less incorrect:
- it was inefficent because useracc() takes much longer than just
accessing the data using a correct access method, at least on i386's.
- it was incorrect because direct access is incorrect unless the address
has been mapped. This and nearby direct accesses are mostly handled
better for other arches because they have to be (direct accesses don't
work).
- using magic in sigreturn is still fundamentally broken because false
matches are possible. On i386's, a false match occurs when %eip in a
new signal context happens to equal the magic value. This is not
handled better for other arches.
is not configured. Including <isa/isavar.h> when it is not used is
harmful as well as bogus, since it includes "isa_if.h" which is not
generated when isa is not configured.
This was fixed in 1999 but was broken by unconditionalizing PNPBIOS.
prior ICP Vortex models. This driver was developed by Achim Leubner
of Intel (previously with ICP Vortex) and Boji Kannanthanam of Intel.
Submitted by: "Kannanthanam, Boji T" <boji.t.kannanthanam@intel.com>
MFC after: 2 weeks
This typo keeps us from properly routing an interrupt for CardBus
bridges on this machine. So, now we look for $PIR and then _PIR to
cope. With these changes, the Libretto L1 now works properly.
Evidentally, the idea comes from patch that the Japanese version of
RedHat (or against a Japanese version of Red Hat), but my Japanese
isn't good enough to to know for sure.
Reported by: Hiroyuki Aizu-san <eyes@navi.org>
# This may be an MFC candidate, but I'm not yet sure.
cpuid with %eax=1 will return a logical cpu count in bits 16-23 of %ebx.
Bit 29 is actually 'TM' according to AP-485. This signifies the presence
of the thermal control circuit (which I believe can slow the clock down
to reduce core temperature).
they make it through to userland. This should fix the p5-smp problem
without affecting the other cpus (eg: cyrix, see initcpu.c and the special
cache handling for these cpu types).
traps on the first instruction of signal handlers.
In trap.c:syscall(), fake a trace trap if the single-step flag was set
on entry to the kernel, not if it will be set on exit from the kernel.
This fixes bogus trace traps after the last instruction of signal handlers.
gdb-4.18 (the version in FreeBSD) still has problems with the program in
the PR. These seem to be due to bugs in gdb and not in FreeBSD, and are
fixed in gdb-5.1 (the distribution version).
PR: 33262
Tested by: k Macy <kip_macy@yahoo.com>
MFC after: 1 day
whether the machine context is valid and whether the FPU state is
valid (saved).
Mark the machine context valid before copying it out when sending a
signal.
Approved by: -arch
mutex releases to not require flags for the cases when preemption is
not allowed:
The purpose of the MTX_NOSWITCH and SWI_NOSWITCH flags is to prevent
switching to a higher priority thread on mutex releease and swi schedule,
respectively when that switch is not safe. Now that the critical section
API maintains a per-thread nesting count, the kernel can easily check
whether or not it should switch without relying on flags from the
programmer. This fixes a few bugs in that all current callers of
swi_sched() used SWI_NOSWITCH, when in fact, only the ones called from
fast interrupt handlers and the swi_sched of softclock needed this flag.
Note that to ensure that swi_sched()'s in clock and fast interrupt
handlers do not switch, these handlers have to be explicitly wrapped
in critical_enter/exit pairs. Presently, just wrapping the handlers is
sufficient, but in the future with the fully preemptive kernel, the
interrupt must be EOI'd before critical_exit() is called. (critical_exit()
can switch due to a deferred preemption in a fully preemptive kernel.)
I've tested the changes to the interrupt code on i386 and alpha. I have
not tested ia64, but the interrupt code is almost identical to the alpha
code, so I expect it will work fine. PowerPC and ARM do not yet have
interrupt code in the tree so they shouldn't be broken. Sparc64 is
broken, but that's been ok'd by jake and tmm who will be fixing the
interrupt code for sparc64 shortly.
Reviewed by: peter
Tested on: i386, alpha
they were right. Fix both kenter() and kremove() for SMP by ensuring that
the tlb is flushed on other cpu's. This will directly solve random-corruption
panic issues in -stable when it is MFC'd. Better to be safe then sorry, we
can optimize this later.
Original Suspicion by: peter
Maybe MFC: immediately on re's permission
