- The claim in the commit log of rev. 1.11 of dev/uart/uart_cpu_sparc64.c
etc. that UARTs are the only relevant ISA devices on sparc64 turned out
to be false. While there are sparc64 models where UARTs are the only
devices on the ISA bus there are in fact also low-cost models where all
devices traditionally found on the EBus are hooked up to the ISA bus.
There are also models that use a mix between EBus and ISA devices with
things like an AT keyboard controller and other rather interesting
devices that we might want to support in the futute hook up to the ISA
bus.
In order to not need to add sparc64 specific device_identify methods to
all of the respective ISA drivers and also not add OFW specific code to
the common ISA code make the sparc64 ISA bus code fake up PnP devices so
most ISA drivers probe their devices without further changes.
Unfortunately Sun doesn't adhere to the ISA bindings defined in IEEE
1275-1994 for the properties of most of the ISA devices which would
allow to obtain the vendor and logical IDs from their properties. So we
we just use a simple table which maps the name properties to PnP IDs.
This could be done in a more sophisticated way but I courrently don't
see the need for this. [1]
- Add the children with fully mapped and specified resources (in the OFW
sense) similar to what is done in the EBus code for the IRQ resources
of the children as adjusting the resources and the resource list entries
respectively in isa_alloc_resource() as done perviously causes trouble
with drivers which use rman_get_start(), pass-through or allocate and
release resources multiple times, etc.
Adjusting the resources might be better off in a bus_activate_resource
method but the common ISA code currently doesn't allow for an
isa_activate_resource(). [2]
With this change:
- ppbus(4) and lpt(4) attach and work (modulo ECP mode, which requires
real ISADMA code but it currently only consists of stubs on sparc64).
- atkbdc(4) and atkbdc(4) attach, no further testing done.
- fdc(4) itself attaches but causes a hang while attaching fd0 also
when is DMA disabled, further work in fdc(4) is required here as e.g.
fd0 uses the address of fd1 on sparc64 (not sure if sparc64 supports
more than one floppy drive at all).
All of these drivers previously caused panics in the sparc64 ISA code.
- Minor changes, e.g. use __FBSDID, remove a dupe word in a comment and
declare one global variable which isn't used outside of isa.c static.
o dev/uart/uart_cpu_sparc64.c and modules/uart/Makefile:
- Remove the code for registering the UARTs on the ISA bus from the
sparc64 uart_cpu_identify() again and rely on probing them via PnP.
Original idea by: tmm [1]
No objections by: tmm [1], [2]
I have in mind for the genclock interface):
- Recognize the MK48T18 as well (differs from the MK48T08 only in
packaging options and voltages).
- Allow MD code to provide functions for reading/writing NVRAM/RTC
locations.
If passed NULL, the old behaviour using bus_space_{read,write}_1() is
used. Otherwise, all access to the chip goes via the MD functions.
This is necessary for mvmeppc boards where the mk48txx NVRAM/RTC is
not directly addressable.
- Cleanup MI mk48txx(4) todclock driver:
- Prepare mk48txxvar.h and leave only register definitions in
mk48txxreg.h.
- Define struct mk48txx_softc as usual devices and allocate necessary
members in it.
- Change mk48txx_attach() to only take a device_t.
o While converting the sparc64 eeprom driver to the above changes:
- Remove some dead code and stale comments.
- Use the NVRAM size provided by the mk48txx driver instead of hardcoding
it as suggested by a comment.
- Add a comment about why it doesn't make much sense to read the hostid
directly from the NVRAM except for displaying it when attaching.
- Don't print the hostid if it reads all zero because it's stored
elsewhere.
after boot so that PCI is initialized and we can probe for the problem
chipsets. Note that while probed but unusable states are disabled, they
aren't freed yet. In the future, it may make sense to detach them.
Tested by: Adam K Kirchoff <adamk at voicenet com>
MFC after: 2 days
backed out commits were trying to address: when cancelling the timeout
callout, also cancel the abort_task event, since it is possible that
the timeout has already fired and set up an abort_task.
also fix up handling and proding of the tx, _OACTIVE is now handled
better...
Submitted by: Peter Edwards (sk_jfree)
Obtained from: OpenBSD and/or NetBSD (tx prod)
i386 to dev/acpi_support. In theory, these devices could be found
other than in i386 machines only as amd64 becomes more popular. These
drivers don't appear to do anything i386 specific, so move them to
dev/acpi_support. Move config lines to files so that those
architectures that don't support kernel modules can build them into
the kernel. At the same time, rename acpi_snc to acpi_sony to follow
the lead of all the other specialty devices.
connects to the keyboard and mouse and needs some special treatment.
Until this is fully understood, implemented and tested, simply avoid
probing the second Z8530. This is also what the zs(4) driver does.
current baudrate setting. Use this ioctl() when we don't know the
baudrate of the sysdev (as represented by a 0 value). When the
ioctl() fails, e.g. when the backend hasn't implemented it or the
hardware doesn't provide the means to determine its current baudrate
setting, we invalidate the baudrate setting by setting it to -1.
None of the backends currently implement the new ioctl().
A baudrate we consider insane is silently replaced with 0. When the
baudrate is 0, we will not try to program the hardware. Instead we
leave the communication speed unaltered, maximizing the chance to
have a working console. Obviously this means we allow specifying a
0 baudrate for exactly that purpose.
- Because em_encap() can now fail in a way that leaves us without an
mbuf chain, potentially set *m_headp to NULL if that happens, so that
the caller can do the right thing. This case can occur when we try
to prepend the vlan header mbuf but can't allocate additional memory.
- Modify the caller of em_encap() to detect a NULL m_head and not try
to queue the mbuf if that happens.
- When em_encap() fails, make sure to call bus_dmamap_destroy() to
clean up.
but sk(4) is so prevalent on AMD64 motherboards we need to reduce the number
of round trips in the mailing lists trying to get sufficient information to
make sure we've got a handle on all the problems and are working towards
making sk(4) solid.
Submitted by: bz
isn't worth adding to the modules lists that we have to hard code for
this to work. Since we print PID right away, we have a trace point
already.
Minor knf while I'm here.
Use this in all the places where sleeping with the lock held is not
an issue.
The distinction will become significant once we finalize the exact
lock-type to use for this kind of case.
models of laptops, which are essentially the same as the normal
ones, as far as acpi_asus is concerned[1]
o Use the above as an excuse to reshuffle the mess I made of the
probe function when I originally wrote it.
Reported by: Soeren Larsen <soeren@whiteswan.dk>
promiscuous mode introduced in 1.45, which programs the em card not
to strip or prepend tags when in promiscuous mode without also
modifying behavior to manually prepend a vlan header in the event
that the card isn't doing it on transmit. Due to a feature of card
operation, if the global VLAN prepend/strip register isn't set,
setting the VLAN tag flag on individual packet descriptors will
cause the packet to be transmitted using ISL encapsulation rather
than 802.1Q VLAN encapsulation.
This fix causes em_encap() to prepend the header by tracking whether
the card is configured to temporarily disable prepending/stripping
due to promiscuous mode. As a result, entering promiscuous mode on
the parent em interface no longer causes vlans to appear to "wedge"
or transmit ISL-encapsulated frames, which typically will not be
configured/spoken by the other endpoints on the VLAN trunk. This
bug may also exist in other drivers, and the additional vlan
encapsulation logic should be abstracted and centralized in
if_vlan.c if so.
RELENG_5_3 candidate.
MFC after: 1 week
Tested by: pjd, rwatson
Reported by: astesin at ukrtelecom dot net
Reported by: Mike Tancsa <mike at sentex dot net>
Reported by: Iasen Kostov <tbyte at OTEL dot net>
reports of problems. The bug is probably that there are cases where
`xfer->timeout && !sc->sc_bus.use_polling' is not a suitable test
for an active timeout callout, so an explicit flag will be necessary.
Apologies for the breakage.
the tree. Small tweaks were made by myself to eliminate unnecessary
includes and some other minor issues. Last time I asked takawata-san
about this driver, he suggested I commit it.
Submitted by: takawata
a bridge without a _PRT were a _PRT was needed. Instead, the warning in
dmesg is a false warning and only serves to cause unnecessary concern.
MFC after: 1 week
transfer timeouts that typically cause a transfer to be completed
twice, resulting in panics and page faults:
o A transfer completion interrupt could arrive while an abort_task
event was set up, so the transfer would be aborted after it had
completed. This is very easy to reproduce. Fix this by setting
the transfer status to USBD_TIMEOUT before scheduling the
abort_task so that the transfer completion code will ignore it.
o The transfer completion code could execute concurrently with the
timeout callout, leaving the callout blocked (e.g. waiting for
Giant) while the transfer completion code runs. In this case,
callout_stop() does not prevent the callout from running, so
again the timeout code would run after the transfer was complete.
Handle this case by checking the return value from callout_stop(),
and ignoring the transfer if the callout could not be removed.
o Finally, protect against a timeout callout occurring while a
transfer is being aborted by another process. Here we arrange
for the timeout processing to ignore the transfer, and use
callout_drain() to ensure that the callout has really gone before
completing the transfer.
This was tested by repeatedly performing USB transfers with a timeout
set to approximately the same as the normal transfer completion
time. In the PR below, apparently this occurred by accident with a
particular printer and the default timeout.
PR: kern/71491
just a convenience function to be called from debuggers that gets
compiled in when EHCI_DEBUG is defined. Move its declaration to
make this more obvious.
supported for STAILQ via STAILQ_CONCAT().
(2) Maintain a count of the number of entries in the thread-local entropy
fifo so that we can keep the other fifo counts in synch.
MFC after: 3 weeks
MFC with: randomdev_soft.c revisions 1.5 and 1.6
Suggested by: jhb (1)
o Reduce the interrupt delay to 2 microframes.
o Follow the spec more closely when updating the overlay qTD in the QH.
o No need to generate an interrupt at the data part of a control
transfer, it's generated by the status transfer.
o Make sure to update the data toggle on short transfers.
o Turn the printf about needing toggle update into a DPRINTF.
o Keep track of what high speed port (if any) a device belongs to
so we can set the transaction translator fields for the transfer.
o Verbosely refuse to open low/full speed pipes that depend on
unimplemented split transaction support.
o Fix various typos in comments.
Obtained from: NetBSD
control the number of lines per page rather than a constant. The variable
can be examined and changed in ddb as '$lines'. Setting the variable to
0 will effectively turn off paging.
- Change db_putchar() to force out pending whitespace before outputting
newlines and carriage returns so that one can rub out content on the
current line via '\r \r' type strings.
- Change the simple pager to rub out the --More-- prompt explicitly when
the routine exits.
- Add some aliases to the simple pager to make it more compatible with
more(1): 'e' and 'j' do a single line. 'd' does half a page, and
'f' does a full page.
MFC after: 1 month
Inspired by: kris
* Announce some more fields from ro area for better debugging of broken
sk(4)s on various boards.
Submitted by: Bjoern A. Zeeb <bzeeb-lists@lists.zabbadoz.net>
entered the interface start function, no packets were actually dequeued.
Therefore, keep a count of how many packets we really added onto the tx
chain, and initiate a transmit only if the count is non-zero.
the device is suspended or shutting down. This will need to be rethought
slightly if we implement suspend/resume support within vr(4).
This appears to fix the vr_shutdown() panic on SMP machines.
My theory here is there's a race somewhere during vr_detach() with
vr_intr() in the SMP case which was sometimes being triggered,
although quite why this was happening is unclear (vr_stop() also
explicitly disables interrupts by writing to the IMR register).
MFC-to-RELENG_5* candidate.
PR: kern/62889
Tested by: seb at struchtrup dot com
MFC after: 10 days
on UltraSPARC workstations. The driver is based on OpenBSD's SBus
cs4231 driver and heavily modified to incorporate into sound(4)
infrastructure. Due to the lack of APCDMA documentation, the DMA
code of SBus cs4231 came from OpenBSD's driver.
The driver runs without Giant lock and supports both SBus and EBus
based CS4231 audio controller. Special thanks to marius for providing
feedbacks during the driver writing. His feedback made it possible
to write hiccup free playback code under high system loads.
Approved by: jake (mentor)
Reviewed by: marius (initial version)
Tested by: marius, kwm, Julian C. Dunn(jdunn AT opentrend DOT net)
two loops in agp_generic_bind_memory(). As an intended side-effect, all
of the calls to vm_page_wakeup() are now performed with the containing
vm object lock held.
o Instead of locking and unlocking all over the place, use
lock assertions to make certain that the bfe lock is held
where necessary.
o Create locked and unlocked versions of bfe_init and bfe_start. These
functions can be called from outside the module and by functions
within the bfe module. The calls from outside the module don't
hold the bfe lock so the unlocked versions called by these functions
simple obtain the bfe lock and call the locked version.
- Fix a typo (scp) in the locking macros that only worked because in all the
instances in which it was called the softc pointer happened to be named 'sc'.
- Mark the interrupt MPSAFE
Tested by: matusita, Dario Freni <saturnero@gufi.org>
Silence from: -net, wpaul
with a weak memory model or x86 + PAE (or more specifically, your
driver is using bounce pages) and you have had problems with em(4),
this may fix it. At least this is needed to have em(4) work properly
on FreeBSD/arm.
Original version by: cognet
Reviewed by: tackerman
Tested by: cognet
Add constants for SPI protocol delays that are needed for
target mode.
aic7xxx.c:
Correct a target mode issue that caused an occassional
spurious REQ to be seen on the bus when performing manual
message processing (e.g. transfer rate negotiation).
Enforce phase change bus settle rules with explicit
delays when performing manual message processing in
target mode. The sequencer already did this for
"fast-path", target mode message processing.
as the original logic did. This fixes a race with vr_intr() which was
masked on UP systems and manifested on SMP systems.
PR: kern/62889
MFC after: 1 day
the ATA pccard locking function. This makes pccard devices like
Compact Flash cards work again.
PR: kern/72805
Submitted by: James E. Flemer <jflemer@alum.rpi.edu>
MFC in: 2 days
frames. BGE hardware with the rx alignment bug will still be handled by the
calls to m_adj() that already exist. m_adj() is probably better suited for
this task anyways. Just as with if_em, this saves a malloc + several locks
per packet and prevents unneeded data copying within busdma.
Since the e1000 DMA engines hava no constraints on the alignment of buffer
transfers, there is no reason to tell busdma that there is. This save a
minimum of 1 malloc call per packet, which translates to eliminating 4 locks.
It also means that buffers are not needlessly bounced when transfered. The
end result is a 38% improvement in pps in a 4 way bridging environment.
Obtained from: Sandvine, Inc.
(usually taking 20 seconds to transmit a packet).. no longer fall back
to only transmitting one packet (instead of the entire queue) after we
have processed the entire send queue... I have no idea why we didn't
start seeing this problem ~6 years ago when this code was introduced...
modes on a tty structure.
Both the ".init" and the current settings are initialized allowing
the function to be used both at attach and open time.
The function takes an argument to decide if echoing should be enabled.
Echoing should not be enabled for regular physical serial ports
unless they are consoles, in which case they should be configured
by ttyconsolemode() instead.
Use the new function throughout.
constrained to a small number of sessions by the small on-card memories found
in newer devices. This is really a stopgap solution as having session state
in main memory incurs a (small but noticeable) performance penalty. The better
solution is to manage session state so that it's cached on chip.
Obtained from: openbsd
The changes in the next commit would make the code totally unreadable
if the #ifdef'ing were maintained.
It might make a lot of sense to split if_cx.c in a netgraph related
and in a tty related file but I will not attempt that without hardware.
handle DMA addresses located above 1GB. The LBA(loop begin address)
register which holds DMA base address is 32bits register. But the
MSB 2bits are used for other purposes. This effectivly limits the
DMA address space up to 1GB.
Approved by: jake (mentor)
Reviewed by: truckman, matk
assign DMA address to the wrong address. It can cause system lockup
or other mysterious errors. Since most sound cards requires low DMA
address(BUS_SPACE_MAXADDR_24BIT) sndbuf_alloc() would fail when the
audio driver is loaded after long running of operations.
Approved by: jake (mentor)
Reviewed by: truckman, matk
- Implement dcons_ischar() and dcons_load_buffer().
- If loader passed a dcons buffer address, keep using it.
(We still need a patch to cheat memory management system.)
asynchronous. I realize that this means the custom application will
not work as written, but it is not okay to break most users of ugen(4).
The major problem is that a bulk read transfer is not an interrupt
saying that X bytes are available -- it is a request to be able to
receive up to X bytes, with T timeout, and S short-transfer-okayness.
The timeout is a software mechanism that ugen(4) provides and cannot
be implemented using asynchronous reads -- the timeout must start at
the time a read is done.
The status of up to how many bytes can be received in this transfer
and whether a short transfer returns data or error is also encoded
at least in ohci(4)'s requests to the controller. Trying to detect
the "maximum width" results in using a single buffer of far too
small when an application requests a large read.
Even if you combat this by replacing all buffers again with the
maximal sized read buffer (1kb) that ugen(4) would allow you to
use before, you don't get the right semantics -- you have to
throw data away or make all the timeouts invalid or make the
short-transfer settings invalid.
There is no way to do this right without extending the ugen(4) API
much further -- it breaks the USB camera interfaces used because
they need a chain of many maximal-width transfers, for example, and
it makes cross-platform support for all the BSDs gratuitously hard.
Instead of trying to do select(2) on a bulk read pipe -- which has
neither the information on desired transfer length nor ability to
implement timeout -- an application can simply use a kernel thread
and pipe to turn that endpoint into something poll-able.
It is unfortunate that bulk endpoints cannot provide the same semantics
that interrupt and isochronous endpoints can, but it is possible to just
use ioctl(USB_GET_ENDPOINT_DESC) to find out when different semantics
must be used without preventing the normal users of the ugen(4) device
from working.
New devicename is ttyy{unit}{port}
No callout devices created as there is no modemcontrol on these ports.
Add data structure to represent each port to avoid excessive array use.
from within umass_ufi_transform(). This includes the 12-byte commands
FORMAT_UNIT, WRITE_AND_VERIFY, VERIFY, and READ_FORMAT_CAPACITIES
(sorted in numerical order).
Reviewed by: ken, scottl
MFC after: 2 weeks
md(8). The former is generally not going to fail, but the latter can
fail when the underlying swap device returns an error.
There are still plenty of other places where vm_pager_get_pages() failing
will lead directly to crashes, so it's a good idea to put your swap on
RAID if you care enough to put any of your disks on RAID....
that conjures up the device node so it isn't true PNP. Noticed by jhb@.
* Add an attachment for esscontrol since it too uses ISA_PNP_PROBE.
* Move an attachment from snd_mss to snd_pnpmss. The latter is the real
PNP user.
* Fix a bug where caches were flushed on non-C3 transitions.
* Be sure a working flush cache instruction is present before using it.
* Disable C3 completely if it isn't present.
may want to shut down here but the chance of BIOS vendors getting this
wrong is high. They're only supposed to announce this when all batteries
hit their critical level but past experience indicates we should be
conservative about this for now.
- Trade off granularity to reduce overhead, since the current model
doesn't appear to reduce contention substantially: move to a single
harvest mutex protecting harvesting queues, rather than one mutex
per source plus a mutex for the free list.
- Reduce mutex operations in a harvesting event to 2 from 4, and
maintain lockless read to avoid mutex operations if the queue is
full.
- When reaping harvested entries from the queue, move all entries from
the queue at once, and when done with them, insert them all into a
thread-local queue for processing; then insert them all into the
empty fifo at once. This reduces O(4n) mutex operations to O(2)
mutex operations per wakeup.
In the future, we may want to look at re-introducing granularity,
although perhaps at the granularity of the source rather than the
source class; both the new and old strategies would cause contention
between different instances of the same source (i.e., multiple
network interfaces).
Reviewed by: markm
be used to announce various system activity.
The auxio device provides auxiliary I/O functions and is found on various
SBus/EBus UltraSPARC models. At present, only front panel LED is
controlled by this driver.
Approved by: jake (mentor)
Reviewed by: joerg
Tested by: joerg
with acpi but the timer runs twice as fast. Note that the main problem
(system doesn't work properly with acpi disabled) should be fixed separately.
Changes:
* Add a quirk to disable the timer
* Merge the P5A and P5A-B quirks since they appear to be based on the
same ASL.
PR: i386/72450
Tested by: Kevin Oberman <oberman es.net>
MFC after: 3 days
This also adds support for bigger disks on the controller I have access to,
and maybe others if I understood the adhoc methods used on those.
Those with more PC98 bigdrive controllers it is hereby invited to add/fix
support for those in geom_pc98.c and not using #ifdef PC98 all over the place.
allocate unallocated memory resources from the top 32MB of the address
space rather than the top 2GB. While the latter works on some
chipsets, it fails badly on others. 32MB is more conservative and
matches what cheap harware from this era is hardwired to pass.
table. acpidump(8) concatenates the body of the DSDT and SSDTs so an
edited ASL will contain all the necessary information. We can't use a
completely empty table since ACPI-CA reports this as a problem.
MFC after: 3 days
+ * 9: 0x3f0-0x3f3,0x3f4-0x3f5,0x3f7
This requires only one change to support. Rather than keying on the
size of the resource being 2, instead key off the end & 7 being 3.
This covers the same cases that the size of 2 would catch, but also
covers the new above case.
In addition, I think it is clearer to use the end in preference to the
size and start for case #8 as well. Turns two tests into one, and
catches no other cases.
Make minor commentary changes to deal with new case #9.
# This change is specifically minimal to allow easy MFC. A more
# extensive change will go into current once I've had a chance to test
# it on a lot of hardware...
data endpoints. The control endpoint doesn't need read/write/poll
operations, and more importantly, the thread counts should be
separate so that the control endpoint can properly reference itself
while deleting and recreating the data endpoints.
* Add some macros that handle referencing/releasing devices, and use them
for sleeping/woken-up and open/close operations as apppropriate.
* Use d_purge for FreeBSD, and a loop testing the open status for all
the endpoints for NetBSD and OpenBSD, so that when the device is
detached, the right thing always happens.
restart the current waiting transfer. If this isn't done, the device's
next transfer (that we would like to do a short read on) is going to
return an error -- for short transfer.
* For bulk transfer endpoints, restore the maximum transfer length each
time a transfer is done, or the first short transfer will make all the
rest that size or smaller.
* Remove impossibilities (malloc(M_WAITOK) == NULL, &var == NULL).
New device names are "{tty|cua}A$(card)$(port)[.init|.lock]"
Put a portname in the port structure if SI_DEBUG is defined to avoid
need to inspect minor number to construct name..
Constify some strings.
Remove duplicated DBG_ #defines.
is a no-op on little endian architectures, but fixes getting the MAC
address for some dc(4) cards on big endian architectures.
This is a RELENG_5 candidate.
Tested by: gallatin (powerpc), marius (sparc64)
First version of the patch written by: gallatin
