- Add stubs for EISA and SBUS cards.
(VME, FutureBUS, and TurboChannel stubs not provided.)
- Add infrastructure to build driver and bus front-end modules.
lun address modifier of sorts. Only an HP XP-512 seems to have cared.
Fix a few misplaced pointers for the new fabric goop, which has been
demonstrated to work on newer Brocades and McData switches now.
Put in commented out code which would run GFF_ID if the QLogic f/w
allowed it.
Don't whine about not being able to find a handle for a command if it
was a command aborted (by us).
o move timeout from wihap_info to wihap_sta_info
o sprinkle spls into the code (need to use proper -current locking)
o better use of le16toh and htole16
o fix a few leaks m_freem(m)
o minor knf
o minor de-knf to match OpenBSD
o de__P
- Add a device_method_t array, fore_methods.
- Add a fore_ident_table that contains the various FORE Systems PCA-200
series devices.
- Rewrite of the fore_probe routine (formerly known as fore_pci_probe).
- Minor changes... mostly WIP stuff to get this updated... still much to
be done.
the per-channel bus_addr_t offset. Also, cast the offset to (long long)
and use %#llx instead of %#x to fix printf warnings on architectures where
sizeof(bus_addr_t) != sizeof(int).
es137x.c: In function `es1371_rdcd':
es137x.c:598: warning: `x' might be used uninitialized in this function
PR: kern/35408
Submitted by: Thomas Quinot <thomas@cuivre.fr.eu.org>
that declares itself to be a disk, which may be the wrong thing to do in
the long term but it works well enough to attach to emulated disks in the
PowerPC simulator in gdb now that they have the proper device_type
property.
The extra microphone channel capability is part of the "normal" ac97
capabilities and not an extended ac97 capability. Now recording on
codecs without a seperate mic channel works.
MFC after: 1 week
FIFO or the in-RAM descriptors it will switch to RX_IDLE from where it
is not restarted.
We used to deal with RX_IDLE by doing a total reinit but this lost
our link and caused a potential 30sec autonegotiation against
switches. This was changed to a less heavyhanded approach, but this
failed to restart the receiver it it were in the RX_IDLE state.
This change adds the RX_IDLE and the RX_FIFO_OFLOW conditions as
triggers for interrupts and receive side processing, and restarts
the receiver when it is RX_IDLE.
Remove the #ifdef notyet'ed nge_rxeoc() function.
Sponsored by: Cybercity Internet, Denmark.
MFC after: 7 days
(apparently by markus@, at least committed by him). This has the
advantage of not using the bad IV's from Fluhrer/Mantin/Shamir as well
as bringing the drivers a little closer together.
Also use a few constants in place of magic numbers in one place.
Obtained from: OpenBSD 1.25, 1.28, 1.36, 1.38, 1.42
time we tell CAM to rescan the bus. Together with the previous patch
this should avoid the problem where the devices would wedge because they
got spoken to over two different pipes.
Tested by: Tomas Pluskal <plusik@pohoda.cz>
wrote. This code was for 4.5-release, so I've ported it to -current
and made a few minor tweaks. The biggest non-style tweak was to not
make access point the default.
More changes will be needed to get this actually working, but I wanted
to get a relatively pure baseline. This doesn't seem to break what
works now.
attachment after boot in some cases where the device gets confused if
spoken to over two different pipes simultaneously (resulting in TIMEOUT
errors on requesting INQUIRY data).
This solution is far from perfect, as after umass_attach has returned
the USB stack fetches the string descriptors in order for creating the
event that is sent to userland. It just makes the chances of collisions
less likely.
Tested by: Tomas Pluskal <plusik@pohoda.cz>
submitter, this permits Russian (and probably other locales') characters
to be entered via watch(8).
PR: 35636
Submitted by: Gleb Smirnoff <glebius@rinet.ru>
the card for command completion.
digi_delay() uses either tsleep() or DELAY() depending on the value of
``cold''.
Pointed in the right direction by: jhb
Add the card name to the error message for the first initialisation
failure, giving us more info about what was actually discovered.
This code has been tested by Robert Suetterlin <robert@mpe.mpg.de>
to work on a PCI Xem card.
mod_depend * (which may be NULL). The only consumer of this
function at the moment is digi_loadmoduledata(), and that passes
a NULL mod_depend *.
In linker_reference_module(), check to see if we've already got
the required module loaded. If we have, bump the reference count
and return that, otherwise continue the module search as normal.
