remotely, but they would be if e.g. it happened to call the logging
function using a DNS hostname.
Also replace random() by arc4random() - only one of these is arguably
required since it's directly used in the protocol, but we might as
well replace both to avoid using two different PRNGs.
Reviewed by: green, alex
significantly pessimized syscalls by arranging to do null rescheduling
on return from every syscall. (AST_RESCHED was not defined, and the
mask ~AST_RESCHED gets replaced by the useless mask ~0. This bug has
been fixed before, in rev.1.92.)
all-lower or all-upper case characters, respectively. These were added
to further reduce differences between NetBSD/OpenBSD and FreeBSD make(1)
to propagate OpenPackages.
PR: 19959
Submitted by: Gaspar Chilingarav <nm@web.am>
but allows for regex. I removed NO_REGEX since no one could give a reason
to have it, and since we don't use make in bootstrap tools, it's not needed.
This is mostly added to synch up with NetBSD/OpenBSD so as to eliminate
roadblocks in the OpenPackages project (see http://www.openpackages.org/).
It's also quite useful, and costs us only about 3 kilobytes of space.
PR: 21605
Submitted by: Hubert Feyrer <hubertf@NetBSD.org>
Reviewed by: silence on -arch
Obtained from: NetBSD
aic7xxx.c:
In target mode, reset the TQINPOS on every restart of the sequencer.
In the past we did this only during a bus reset, but there are other
reasons the sequencer might be reset.
In ahc_clear_critical_section(), disable pausing chip interrupts while
we step the sequencer out of a critical section. This avoids the
possibility of getting a pausing interrupt (unexpected bus free,
bus reset, etc.) that would prevent the sequencer from stepping.
Send the correct async notifications in the case of a BDR or bus reset.
In ahc_loadseq(), correct the calculation of our critical sections.
In some cases, the sections would be larger than needed.
aic7xxx.h:
Remove an unused SCB flag.
aic7xxx.seq:
MK_MESSAGE is cleared by the kernel, there is no need to waste
a sequencer instruction clearing it.
aic7xxx_freebsd.c:
Go through the host message loop instead of issuing a single
byte message directly in the ahc_timeout() case where we
are currently on the bus to the device. The effect is the same,
but this way we get a nice printf saying that an expected BDR
was delivered instead of an unexpected bus free.
If we are requeuing an SCB for an error recovery action, be sure
to set the DISCONNECTED flag in the in-core version of the SCB.
This ensures that, in the SCB-paging case, the sequencer will
still recognize the reselection as valid even if the version
of the SCB with this flag set was never previously paged out
to system memory. In the non-paging case, set the MK_MESSAGE
flag in SCB_CONTROL directly.
aic7xxx_pci.c:
Enable the Memeory Write and Invalidate bug workaround for
all aic7880 chips with revs < 1. This bug is rarely triggered
in FreeBSD as most transfers end on cache-aligned boundaries,
but a recheck of my references indicates that these chips
are affected.
handler can safely remove itself from a list while being run.
(Note that it is not safe to remove anything else from the same list,
as this may still cause corruption in the case where the removed
item is next on the list.)
kind we can manage in a set of configurations" and "the number of resources
of a particular kind that can be programmed into an ISA PnP adapter".
Submitted by: Motomichi Matsuzaki <mzaki@e-mail.ne.jp>
Submitted by: Hirokazu WATANABE <gwna@geocities.co.jp>
Replace all in-tree uses with necessary subset of <sys/{fb,kb,cons}io.h>.
This is also the appropriate fix for exo-tree sources.
Put warnings in <machine/console.h> to discourage use.
November 15th 2000 the warnings will be converted to errors.
January 15th 2001 the <machine/console.h> files will be removed.
non-LVD controllers. We only need to take special action on the qinfifo
if we have dectected the case of an SCB that has been removed from the
qinfifo but has not been fully DMAed to the controller. A missing
conditional caused this code to be executed every time an SCB was
aborted from the queue
Don't attempt to print the path of an SCB that has been freed.
Clean up the traversal of the pending scb list in
ahc_update_pending_syncrates(). This has no functional change.
Correct ahc_timeout()'s requeing of a timedout SCB to effect a
recovery action. We now use ahc_qinfifo_requeue() and a
new function ahc_qinfifo_count() instead of performing the
requeue inline. The old code did not conform to the new qinfifo
method.
Clear the timedout SCB from the disconnected list. This ensures
that the SCB_NEXT field is free to be used for queuing us to
the qinfifo.
wrote, and as such was not very pretty.
Changes that may cause problems for people who use sockstat in scripts:
- sockstat(8) now displays Unix domain sockets in addition to IPv4 and IPv6
- the last period in local and foreign addresses is changed to a colon to
make the port number easier to spot
- IPv4 and IPv6 sockets are listed separately (IPv4 first, then IPv6, then
Unix)
