This should be a big no-op pass; and reduces the size of if_ath.c.
I'm hopefully soon going to take a whack at the USB support for ath(4)
and this'll require some reuse of the busdma memory code.
bridges. Currently this includes information about what resources a
bridge decodes on the upstream side for use by downstream devices including
bus numbers, I/O port resources, and memory resources. Windows and bus
ranges are enumerated for both PCI-PCI bridges and PCI-CardBus bridges.
To simplify the implementation, all enumeration is done by reading the
appropriate config space registers directly rather than querying the
bridge driver in the kernel via new ioctls. This does result in a few
limitations.
First, an unimplemented window in a PCI-PCI bridge cannot be accurately
detected as accurate detection requires writing to the window base
register. That is not safe for pciconf(8). Instead, this assumes that
any window where both the base and limit read as all zeroes is
unimplemented.
Second, the PCI-PCI bridge driver in a tree has a few quirks for
PCI-PCI bridges that use subtractive decoding but do not indicate that
via the progif config register. The list of quirks is duplicated in
pciconf's source.
Reviewed by: imp
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D4171
Hacks to enable target mode there complicated code, while didn't really
work. And for outdated hardware fixing it is not really interesting.
Initiator mode tested with Qlogic 1080 adapter is still working fine.
While later firmware always registers for RSCN requests, older one does
it only in initiator mode. But in target mode there RSCN can be the only
way to detect gone intiator.
For those chips we are not receiving login events, adding initiators
based on ATIO requests. But there is no port ID in that structure, so
in fabric mode we have to explicitly fetch it from firmware to be able
to do normal scan after that.
Lower the payload data (IP) portion of the MTU from 0x10000 to
IP_MAXPACKET (0xFFFF) to avoid panicing the IP stack.
Sponsored by: EMC / Isilon Storage Division
This feature is disabled by default. To enable it, tune
hw.if_ntb.enable_xeon_watchdog to non-zero.
If enabled, writes an unused NTB register every second to demonstrate to
a hardware watchdog that the NTB device is still alive. Most machines
with NTB will not need this -- you know who you are.
Sponsored by: EMC / Isilon Storage Division
This change simplifies and unifies port adding/updating for loop and
fabric scanners. It also fixes problems with scanning restarts due to
concurrent port databases changes. It also fixes many cosmetic issues.
RX buffers from number of received packets.
Differential Revision: https://reviews.freebsd.org/D4178
Submitted by: Drew Gallatin <gallatin@freebsd.org>
Sponsored by: Mellanox Technologies
MFC after: 3 days
Setting sysctl dev....conf.hw_lro may fail if the net device lro is
turned off. Due to the nature of our sysctl handler we need to set the
values back to 0 and issue an error.
Differential Revision: https://reviews.freebsd.org/D4177
Submitted by: Shahar Klein <shahark@mellanox.com>
Sponsored by: Mellanox Technologies
MFC after: 3 days
Discard the unused rx_free_q. Instead, reuse inputed packets by putting
them back on the *pend* queue after reinitialization.
If tx or rx handlers are unavailable, free mbufs rather than leaking
them.
With this change, if_ntb can receive more than 100
(NTB_QP_DEF_NUM_ENTRIES) packets.
Sponsored by: EMC / Isilon Storage Division
32-bit BARs can only address memory mapped in the low 32 bits of
physical RAM. Expose this as a 'plimit' out parameter from
ntb_mw_get_range().
Fix if_ntb to allocate memory within this limit.
Sponsored by: EMC / Isilon Storage Division
Sometimes they'll read spurious values (observed: 0xc on Broadwell-DE),
failing link negotiation.
Discussed with: Dave Jiang, Allen Hubbe
Sponsored by: EMC / Isilon Storage Division
The tunable 'hw.ntb.enable_writecombine' may be set to zero to
administratively disable write combining the mapped NTB region.
Sponsored by: EMC / Isilon Storage Division
Use bus_space_write instead of (non-volatile) C pointer writes via an
iowrite32() shim in the same places as the Dual BSD/GPL Linux driver.
Update some types to fixed 32-bit sizes.
Sponsored by: EMC / Isilon Storage Division
Current Xen resume code clears all pending bitmap IPIs on resume, which is
not correct. Instead re-inject bitmap IPI vectors on resume to all CPUs in
order to acknowledge any pending bitmap IPIs.
Sponsored by: Citrix Systems R&D
MFC after: 2 weeks
Modern cards in most cases operate abstract port handles, that have no
any relation to real loop IDs. Leave loopid used only where it really
goes about local loop IDs.
While there, fix few more cases where LUNs were still printed in decimal.
It turns out on a 16550 w/ a 25MHz SoC reference clock you get a little
over 3% error at 115200 baud, which causes this to fail.
Just .. cope. Things cope these days.
Default to 30 (3.0%) as before, but allow UART_DEV_TOLERANCE_PCT to be
set at build time to change that.
Switch PCI register reads from using magic numbers to using the names
defined in pcireg.h
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4185
Using other values causes VMXNET3_CMD_ENABLE to fail. The Linux
driver also enforces this restriction.
Reviewed by: bryanv
MFC after: 1 week
Sponsored by: Norse
Differential Revision: https://reviews.freebsd.org/D4139
accident with RTL8168G and later chips when the interface actually was
brought up. This is due to the fact that with these MAC variants, RXDV
gate needs be disabled for WOL to work. So do just that in re_setwol()
when IFCAP_WOL is requested.
Reported and tested by: dhw
MFC after: 3 days
The code tracks a counter which is the number of events until the next
sample. On context switch in, it loads the saved counter. On context
switch out, it tries to calculate a new saved counter.
Problems:
1. The saved counter was shared by all threads in a process. However, this
means that all threads would be initially loaded with the same saved
counter. However, that could result in sampling more often than once every
X number of events.
2. The calculation to determine a new saved counter was backwards. It
added when it should have subtracted, and subtracted when it should have
added. Assume a single-threaded process with a reload count of 1000 events.
Assuming the counter on context switch in was 100 and the counter on context
switch out was 50 (meaning the thread has "consumed" 50 more events), the
code would calculate a new saved counter of 150 (instead of the proper 50).
Fix:
1. As soon as the saved counter is used to initialize a monitor for a
thread on context switch in, set the saved counter to the reload count.
That way, subsequent threads to use the saved counter will get the full
reload count, assuring we sample at least once every X number of events
(across all threads).
2. Change the calculation of the saved counter. Due to the change to the
saved counter in #1, we simply need to add (modulo the reload count) the
remaining counter time we retrieve from the CPU when a thread is context
switched out.
Differential Revision: https://reviews.freebsd.org/D4122
Approved by: gnn (mentor)
MFC after: 1 month
Sponsored by: Juniper Networks
On my own tests I see no effect from this change, but I also can't
reproduce the reported problem in general.
PR: 127391
PR: 204554
Submitted by: satz@iranger.com
MFC after: 2 weeks
Changes to the code to gather user stacks:
* Delay setting pmc_cpumask until we actually have the stack.
* When recording user stack traces, only walk the portion of the ring
that should have samples for us.
Sponsored by: Juniper Networks
Approved by: gnn (mentor)
MFC after: 1 month
Currently, there is a single pm_stalled flag that tracks whether a
performance monitor was "stalled" due to insufficent ring buffer
space for samples. However, because the same performance monitor
can run on multiple processes or threads at the same time, a single
pm_stalled flag that impacts them all seems insufficient.
In particular, you can hit corner cases where the code fails to stop
performance monitors during a context switch out, because it thinks
the performance monitor is already stopped. However, in reality,
it may be that only the monitor running on a different CPU was stalled.
This patch attempts to fix that behavior by tracking on a per-CPU basis
whether a PM desires to run and whether it is "stalled". This lets the
code make better decisions about when to stop PMs and when to try to
restart them. Ideally, we should avoid the case where the code fails
to stop a PM during a context switch out.
Sponsored by: Juniper Networks
Reviewed by: jhb
Approved by: gnn (mentor)
Differential Revision: https://reviews.freebsd.org/D4124
There is no need for the upstream and downstream addresses to be
different for the NTB configs. Go to using a single set of address. It
is still possible to configure them differently using module parameter
override however (CEM: tunable).
Authored by: Dave Jiang <dave.jiang@intel.com>
Reviewed by: Allen Hubbe <Allen.Hubbe@emc.com>
Reviewed by: Jon Mason <jdmason@kudzu.us>
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Remove the use of sbuf_data on drained sbufs from the debug sysctls:
* ixl_sysctl_hw_res_alloc
* ixl_sysctl_switch_config
This prevents a kernel panic when accessing these values under a kernel
compiled with INVARIANTS.
Sponsored by: Multiplay
Order of operations issue with the QP Num and MW count, which would
result in the receive buffer pointer being invalid if there are more
than 1 MW. Corrected with parenthesis to enforce the proper order of
operations.
Reported by: John I. Kading <John.Kading@gd-ms.com>
Reported by: Conrad Meyer <cem@FreeBSD.org>
Authored by: Jon Mason <jdmason@kudzu.us>
Obtained from: Linux (Dual BSD/GPL driver)
Sponsored by: EMC / Isilon Storage Division
Because it can sleep drainking link work callout(s). Linux (dual
BSD/GPL driver) does something very similar.
At the same time, switch the NTB CTX lock to a non-spin mutex, because
the taskqueue_swi lock can't be taken after a spin mutex.
Suggested by: Witness
Sponsored by: EMC / Isilon Storage Division
In ntb_poll_link, we are intentionally writing the link bit, which is
absent from db_valid_mask. Don't panic on a kassert when we do so.
The Linux version of this (dual BSD/GPL) driver has the db_valid_mask
assertions in callers of db_iowrite() rather than db_iowrite() itself;
it skips the assertions in the equivalent of ntb_poll_link(). Rather
than duplicating the assertions in every caller, add a db_iowrite_raw()
that doesn't check and use it from ntb_poll_link().
Suggested by: kassert_panic
Sponsored by: EMC / Isilon Storage Division
from Mellanox Technologies. The current driver supports ethernet
speeds up to and including 100 GBit/s. Infiniband support will be
done later.
The code added is not compiled by default, which will be done by a
separate commit.
Sponsored by: Mellanox Technologies
MFC after: 2 weeks
the TOE for LAN operation. It is possible to set this to other values
(cluster for networks with little loss and really tight RTTs, and wan
for relatively large RTTs and/or lossy networks) depending on the
environment in which the TOE is being used.
None of this affects plain NIC operation in any way.
MFC after: 1 week
- Split urtwn_tx_start() into urtwn_tx_data() and urtwn_tx_start()
(the last will be used for beacon updates / raw xmit path).
- Remove unneeded code from _urtwn_getbuf().
- Use CCK11 for data frames in 11b mode.
- Send EAPOL frames at 1 Mbps.
- Reduce code duplication in urtwn_tx_data().
- Fix sequence numbering.
- Add IEEE80211_RADIOTAP_F_WEP flag for encrypted frames.
- Check URTWN_RUNNING flag under lock.
Tested with RTL8188EU, STA mode.
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4017
Right now the only way to force a cold reset is:
* The HAL itself detects it's needed, or
* The sysctl, setting all resets to be cold.
Trouble is, cold resets take quite a bit longer than warm resets.
However, there are situations where a cold reset would be nice.
Specifically, after a stuck beacon, BB/MAC hang, stuck calibration results,
etc.
The vendor HAL has a separate method to set the reset reason (which is
how HAL_RESET_BBPANIC gets set) which informs the HAL during the reset path
why it occured. This is almost but not quite the same; I may eventually
unify both approaches in the future.
This commit just extends HAL_RESET_TYPE to include both status (eg BBPANIC)
and type (eg do COLD.) None of the HAL code uses it yet though; that'll
come later.
It also is a big no-op in each HAL - I need to go teach each of the HALs
about cold/warm reset through this path.
Using unmapped IO is really beneficial when running inside of a VM,
since it avoids IPIs to other vCPUs in order to invalidate the
mappings.
This patch adds unmapped IO support to blkfront. The following tests
results have been obtained when running on a Xen host without HAP:
PVHVM
3165.84 real 6354.17 user 4483.32 sys
PVHVM with unmapped IO
2099.46 real 4624.52 user 2967.38 sys
This is because when running using shadow page tables TLB flushes and
range invalidations are much more expensive, so using unmapped IO
provides a very important performance boost.
Sponsored by: Citrix Systems R&D
MFC after: 2 weeks
X-MFC-with: r290610
dev/xen/blkfront/blkfront.c:
- Add and announce support for unmapped IO.
before their initial configuration is done, it turns out that r281337
has the inverse effect on some older chips. Moreover, as with newer
chips before, two chips seemingly identical according to their MAC
revisions may behave differently in this regard, with most working
but a few not, making changes extremely hard to test.
Closer inspection of the corresponding Linux code suggests that RX
and TX should only be enabled after their initial configuration with
RTL8168G and later chips, i. e. RTL8106E{,US}, RTL8107E, as well as
RTL8168{EP,G,GU,H}, so limit the new code path to these. [1]
- Distinguish between RTL8168H and RTL8107E, with the latter being the
10/100-Mbit/s-only variant of the former.
- For MAC variants that can only do Fast Ethernet at a maximum, ensure
that we don't advertise Gigabit Ethernet speed.
- In re_stop(), do the inverse of re_init_locked() and enable RXDV
gate on RTL8168G and later chips again, matching what Linux does.
PR: 203422 [1]
MFC after: 1 week
- Filter out unneeded frames in STA mode.
- Implement ic_promisc() call.
Tested with RTL8188EU, STA and MONITOR modes.
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D3999
learned that the Power8 and the PS3 have a mix of OFW and FDT. Both have AIM
defined. But currently they are not affected. They have no I2C devices under
OFW.
This version was tested on a Quad G5 and build tested for armv6*.
Discussed with nwhitehorn@
Reviewed by: ian@
32-bits aligned. Merge the two bounce buffers into a single one. Some
rough tests showed that the DWC OTG throughput on RPI2 increased by
10% after this patch.
MFC after: 1 week
The mbuf length fields must be set before m_adj() is called else
m_adj() will not always adjust the mbuf and an unaligned read
exception can trigger inside the network stack. This can happen on
platforms where unaligned reads are not supported. Adjust a length
check to include the 2-byte ethernet alignment while at it.
MFC after: 3 days
- Drop TSF initialization; device can discover it without our help.
- Do not touch R92C_BCN_CTRL_EN_BCN bit in STA mode.
- Add 'static' keyword for function definition.
Tested with RTL8188EU, STA mode.
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D3801
- Fix mbuf leaks in iwn_raw_xmit() and iwn_xmit_task()
(regression since r288178).
- Check IWN_FLAG_RUNNING flag under lock.
- Remove m->m_pkthdr.rcvif initialization (fixed in r283994).
- Enclose some values in return statements into parentheses.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4069
attributes when replying to a TLP from a Root Port. As a workaround,
disable No Snoop and Relaxed Ordering in the Root Port of each T5 adapter
during attach so that CPU-initiated requests do not contain these flags.
Note that this affects CPU-initiated requests to all devices under this
root port.
Reviewed by: np
MFC after: 1 week
Sponsored by: Chelsio
PCI-Express capability registers (that is, PCI config registers in the
standard PCI config space belonging to the PCI-Express capability
register set).
Note that all of the current PCI-e registers are either 16 or 32-bits,
so only widths of 2 or 4 bytes are supported.
Reviewed by: imp
MFC after: 1 week
Sponsored by: Chelsio
Differential Revision: https://reviews.freebsd.org/D4088
Since r288350, ic_wme_task() is called via ieee80211_runtask(),
so, any additional deferring from the driver side is not needed.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4072
to transmit the buffer.
ath_tx_start() may manipulate/reallocate the mbuf as part of the DMA
code, so we can't expect the mbuf can be returned back to the caller.
Now, the net80211 ifnet work changed the semantics slightly so
if an error is returned here, the mbuf/reference is freed by the
caller (here, it's net80211.)
So, once we reach ath_tx_start(), we never return failure. If we fail
then we still return OK and we free the mbuf/noderef ourselves, and
we increment OERRORS.
Certain invalid operations trigger hardware error conditions. Error
conditions that only halt one channel can be detected and recovered by
resetting the channel. Error conditions that halt the whole device are
generally not recoverable.
Add a sysctl to inject channel-fatal HW errors,
'dev.ioat.<N>.force_hw_error=1'.
When a halt due to a channel error is detected, ioat(4) blocks new
operations from being queued on the channel, completes any outstanding
operations with an error status, and resets the channel before allowing
new operations to be queued again.
Update ioat.4 to document error recovery; document blockfill introduced
in r290021 while we are here; document ioat_put_dmaengine() added in
r289907; document DMA_NO_WAIT added in r289982.
Sponsored by: EMC / Isilon Storage Division
Fixes race condition observed under following circumstances:
1) I/O split on 128KB boundary with Intel NVMe controller.
Current Intel controllers produce better latency when
I/Os do not span a 128KB boundary - even if the I/O size
itself is less than 128KB.
2) Per-CPU I/O queues are enabled.
3) Child I/Os are submitted on different submission queues.
4) Interrupts for child I/O completions occur almost
simultaneously.
5) ithread for child I/O A increments bio_inbed, then
immediately is preempted (rendezvous IPI, higher priority
interrupt).
6) ithread for child I/O B increments bio_inbed, then completes
parent bio since all children are now completed.
7) parent bio is freed, and immediately reallocated for a VFS
or gpart bio (including setting bio_children to 1 and
clearing bio_driver1).
8) ithread for child I/O A resumes processing. bio_children
for what it thinks is the parent bio is set to 1, so it
thinks it needs to complete the parent bio.
Result is either calling a NULL callback function, or double freeing
the bio to its uma zone.
PR: 203746
Reported by: Drew Gallatin <gallatin@netflix.com>,
Marc Goroff <mgoroff@quorum.net>
Tested by: Drew Gallatin <gallatin@netflix.com>
MFC after: 3 days
Sponsored by: Intel
status registers for every interrupt. Check a common host channel
status interrupt register first, then conditionally read the
individual host channel status registers.
Submitted by: Sebastian Huber <sebastian.huber@embedded-brains.de>
MFC after: 1 week
- Move all files related to the LinuxKPI into sys/compat/linuxkpi and
its subfolders.
- Update sys/conf/files and some Makefiles to use new file locations.
- Added description of COMPAT_LINUXKPI to sys/conf/NOTES which in turn
adds the LinuxKPI to all LINT builds.
- The LinuxKPI can be added to the kernel by setting the
COMPAT_LINUXKPI option. The OFED kernel option no longer builds the
LinuxKPI into the kernel. This was done to keep the build rules for
the LinuxKPI in sys/conf/files simple.
- Extend the LinuxKPI module to include support for USB by moving the
Linux USB compat from usb.ko to linuxkpi.ko.
- Bump the FreeBSD_version.
- A universe kernel build has been done.
Reviewed by: np @ (cxgb and cxgbe related changes only)
Sponsored by: Mellanox Technologies
AMD64 pmap assumes ranges will be in the DMAP, which isn't necessarily
true for NTB memory windows (especially 64-bit BARs).
Suggested by: pmap_change_attr_locked -> kassert_panic
Sponsored by: EMC / Isilon Storage Division
Allows DMA from/to arbitrary KVA or physical address. /dev/ioat_test
must be enabled by root and is only R/W root, so this is approximately
as dangerous as /dev/mem and /dev/kmem.
Sponsored by: EMC / Isilon Storage Division
For the most of chips (except anscient ones) port handlers have no relation
to port IDs. In such situation old code scanning first 125 handlers was
quite naive. Instead of doing that, send to chip single request to get full
list of port handlers available on specific virtual port and scan only them.
Old code had problems with case of several virtual ports enabled, when port
handlers allocated from global address space could easily go above 125.
This change was successfully tested on 23xx, 24xx and 25xx chips in loop
mode with 4 virtual initiator ports, each seing 50 virtual target ports.
* refactor out the rx filter and operating mode code into a separate
method.
* add some comments about what's left with setting the operating mode
based on what carl9170 does.
* comment out some init from otus_init_mac() - it's no longer needed as
it's always init'ed now.
* add debugging and a missing return around a failure to call m_get2() -
during monitor mode operation I found RXing of frames > 2k, which
fails allocation. I'm sure they're valid (it's configuring 11n RX and
receiving 11n frames even though the driver doesn't "do" 11n)
and may be A-MSDU; but allocations fail and we should handle that
gracefully.
Tested:
* UB82 reference NIC (AR9170 + AR9104 2x2 dual band NIC); STA and
monitor mode operation.
The IOAT hardware supports writing a 64-bit pattern to some destination
buffer. The same limitations on buffer length apply as for copy
operations. Throughput is a bit higher (probably because fill does not
have to spend bandwidth reading from a source in memory).
Support for testing Block Fill has been added to ioatcontrol(8) and the
ioat_test device. ioatcontrol(8) accepts the '-f' flag, which tests
Block Fill. (If the flag is omitted, the tool tests copy by default.)
The '-V' flag, in conjunction with '-f', verifies that buffers are
filled in the expected pattern.
Tested on: Broadwell DE (Xeon D-1500)
Sponsored by: EMC / Isilon Storage Division
Add generic hw descriptor struct and generic control flags struct, in
preparation for other kinds of IOAT operation.
Sponsored by: EMC / Isilon Storage Division
Now on 24xx and above chips it is really possible to simulate several
virtual FC ports with single physical one. For example, it allows to
configure several targets in ctl.conf, assign each of them to separate
virtual port, and let user to control access to them with switch zoning.
I still doubt that all problems are solved there, but at now it passes
at least basic tests.
The new load_ma implementation can cause dereferences when used with
certain drivers, back it out until the reason is found:
Fatal trap 12: page fault while in kernel mode
cpuid = 11; apic id = 03
fault virtual address = 0x30
fault code = supervisor read data, page not present
instruction pointer = 0x20:0xffffffff808a2d22
stack pointer = 0x28:0xfffffe07cc737710
frame pointer = 0x28:0xfffffe07cc737790
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL 0, pres 1, long 1, def32 0, gran 1
processor eflags = interrupt enabled, resume, IOPL = 0
current process = 13 (g_down)
trap number = 12
panic: page fault
cpuid = 11
KDB: stack backtrace:
#0 0xffffffff80641647 at kdb_backtrace+0x67
#1 0xffffffff80606762 at vpanic+0x182
#2 0xffffffff806067e3 at panic+0x43
#3 0xffffffff8084eef1 at trap_fatal+0x351
#4 0xffffffff8084f0e4 at trap_pfault+0x1e4
#5 0xffffffff8084e82f at trap+0x4bf
#6 0xffffffff80830d57 at calltrap+0x8
#7 0xffffffff8063beab at _bus_dmamap_load_ccb+0x1fb
#8 0xffffffff8063bc51 at bus_dmamap_load_ccb+0x91
#9 0xffffffff8042dcad at ata_dmaload+0x11d
#10 0xffffffff8042df7e at ata_begin_transaction+0x7e
#11 0xffffffff8042c18e at ataaction+0x9ce
#12 0xffffffff802a220f at xpt_run_devq+0x5bf
#13 0xffffffff802a17ad at xpt_action_default+0x94d
#14 0xffffffff802c0024 at adastart+0x8b4
#15 0xffffffff802a2e93 at xpt_run_allocq+0x193
#16 0xffffffff802c0735 at adastrategy+0xf5
#17 0xffffffff80554206 at g_disk_start+0x426
Uptime: 2m29s
Add a new flag for DMA operations, DMA_NO_WAIT. It behaves much like
other NOWAIT flags -- if queueing an operation would sleep, abort and
return NULL instead.
When growing the internal descriptor ring, the memory allocation is
performed outside of all locks. A lock-protected flag is used to avoid
duplicated work. Threads that cannot sleep and attempt to queue
operations when the descriptor ring is full allocate a larger ring with
M_NOWAIT, or bail if that fails.
ioat_reserve_space() could become an external API if is important to
callers that they have room for a sequence of operations, or that those
operations succeed each other directly in the hardware ring.
This patch splits the internal head index (->head) from the hardware's
head-of-chain (DMACOUNT) register (->hw_head). In the future, for
simplicity's sake, we could drop the 'ring' array entirely and just use
a linked list (with head and tail pointers rather than indices).
Suggested by: Witness
Sponsored by: EMC / Isilon Storage Division
Assertion used here was invalid. If current thread helds any of locks,
we never want to recurse on them.
Obtained from: Semihalf
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D3903
Add e6000sw driver supporting Marvell 88E6352, 88E6172, 88E6176 switches.
It needs to be attached to mdio interface, exporting SMI access
functionality. e6000sw supports port-based VLAN configuration, per-port
media changing, accessing PHY and switch registers.
e6000sw attaches miibuses and PHY drivers as children. Instead of typical
tick as callout, kthread-based tick is used. This combined with SX locks
allows MDIO read/write calls to sleep. It is expected, because this
hardware requires long delays in SMI read/write procedures, which can not
be handled by busy-waiting.
Reviewed by: adrian
Obtained from: Semihalf
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D3902
This commit introduces support for etherswitch devices that utilize SMI as
a way of accessing its registers. SMI register is located in address space
of mge -- access to it was exported through MDIO interface.
Attachment functions were enhanced so as to ensure proper initialisation
in both cases: 1) PHYs attached directly to mge, 2) PHYs attached to
switch device and switch attached to mge. Attachment of etherswitch device
depends on dts entry with compatible="mrvl,sw" property. If none is found,
typical PHY attachment procedure follows.
In case of switch attached, PHYs' status and configuration is accessible
via etherswitchcfg, and ifconfig shows always-up, non-configurable mge
interfaces.
Due to the fact that there may be simultaneous accessess to SMI
registers (e.g. from PHY attached to one of mge instances and switch
to the other), SMI access interlock was added. It is SX lock,
because sleep ability is necessary -- busy-waiting would result
in poor performance due to long delays required by hardware.
Underlying switch driver is obliged to use sleepable locks as well.
Reviewed by: adrian
Obtained from: Semihalf
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D3900
