finding. The test to compare the mbuf m_len against
a fixed value and then returning needs to be removed.
When using VLANS and doing HW_TAGGING, and IPV6, the
ICMP6 packets actually fail this condition, the constant
assumes that the tag is IN the frame, and its not, so
the length is actually tiny. Furthermore, I'm not sure
what the point was to just return??
MFC after: 3 days
the controller to workaround silicon bug of i82557. Each reset will
re-establish link which in turn triggers MII status change
callback. The callback will try to reconfigure controller if the
controller is not i82557 to enable flow-control. This caused
endless link UP/DOWN when the workaround was enabled on non-i82557
controller.
To fix the issue, apply RX lockup workaround only for i82557.
Previously it blindly checked undocumented EEPROM location such
that it sometimes enabled the workaround for other controllers. At
this time, only i82557 is known to have the silicon bug.
This fixes a regression introduced in r215906 which enabled flow
control support for all controllers except i82557.
Reported by: Karl Denninger (karl <> denninger dot net)
Tested by: Karl Denninger (karl <> denninger dot net)
MFC after: 3 days
or detached. Normally it should be changed through user land ioctl(2)
system calls but it looks there's no apps for USB and no need.
With this patch, libpcap would detect the usbus interfaces correctly and
tcpdump(1) could dump the USB packets into PCAP format with -w option.
However it couldn't print the output to console because there's no
printer-routine at tcpdump(1).
This includes support in the kernel, camcontrol(8), libcam and the mps(4)
driver for SMP passthrough.
The CAM SCSI probe code has been modified to fetch Inquiry VPD page 0x00
to determine supported pages, and will now fetch page 0x83 in addition to
page 0x80 if supported.
Add two new CAM CCBs, XPT_SMP_IO, and XPT_GDEV_ADVINFO. The SMP CCB is
intended for SMP requests and responses. The ADVINFO is currently used to
fetch cached VPD page 0x83 data from the transport layer, but is intended
to be extensible to fetch other types of device-specific data.
SMP-only devices are not currently represented in the CAM topology, and so
the current semantics are that the SIM will route SMP CCBs to either the
addressed device, if it contains an SMP target, or its parent, if it
contains an SMP target. (This is noted in cam_ccb.h, since it will change
later once we have the ability to have SMP-only devices in CAM's topology.)
smp_all.c,
smp_all.h: New helper routines for SMP. This includes
SMP request building routines, response parsing
routines, error decoding routines, and structure
definitions for a number of SMP commands.
libcam/Makefile: Add smp_all.c to libcam, so that SMP functionality
is available to userland applications.
camcontrol.8,
camcontrol.c: Add smp passthrough support to camcontrol. Several
new subcommands are now available:
'smpcmd' functions much like 'cmd', except that it
allows the user to send generic SMP commands.
'smprg' sends the SMP report general command, and
displays the decoded output. It will automatically
fetch extended output if it is available.
'smppc' sends the SMP phy control command, with any
number of potential options. Among other things,
this allows the user to reset a phy on a SAS
expander, or disable a phy on an expander.
'smpmaninfo' sends the SMP report manufacturer
information and displays the decoded output.
'smpphylist' displays a list of phys on an
expander, and the CAM devices attached to those
phys, if any.
cam.h,
cam.c: Add a status value for SMP errors
(CAM_SMP_STATUS_ERROR).
Add a missing description for CAM_SCSI_IT_NEXUS_LOST.
Add support for SMP commands to cam_error_string().
cam_ccb.h: Rename the CAM_DIR_RESV flag to CAM_DIR_BOTH. SMP
commands are by nature bi-directional, and we may
need to support bi-directional SCSI commands later.
Add the XPT_SMP_IO CCB. Since SMP commands are
bi-directional, there are pointers for both the
request and response.
Add a fill routine for SMP CCBs.
Add the XPT_GDEV_ADVINFO CCB. This is currently
used to fetch cached page 0x83 data from the
transport later, but is extensible to fetch many
other types of data.
cam_periph.c: Add support in cam_periph_mapmem() for XPT_SMP_IO
and XPT_GDEV_ADVINFO CCBs.
cam_xpt.c: Add support for executing XPT_SMP_IO CCBs.
cam_xpt_internal.h: Add fields for VPD pages 0x00 and 0x83 in struct
cam_ed.
scsi_all.c: Add scsi_get_sas_addr(), a function that parses
VPD page 0x83 data and pulls out a SAS address.
scsi_all.h: Add VPD page 0x00 and 0x83 structures, and a
prototype for scsi_get_sas_addr().
scsi_pass.c: Add support for mapping buffers in XPT_SMP_IO and
XPT_GDEV_ADVINFO CCBs.
scsi_xpt.c: In the SCSI probe code, first ask the device for
VPD page 0x00. If any VPD pages are supported,
that page is required to be implemented. Based on
the response, we may probe for the serial number
(page 0x80) or device id (page 0x83).
Add support for the XPT_GDEV_ADVINFO CCB.
sys/conf/files: Add smp_all.c.
mps.c: Add support for passing in a uio in mps_map_command(),
so we can map a S/G list at once.
Add support for SMP passthrough commands in
mps_data_cb(). SMP is a special case, because the
first buffer in the S/G list is outbound and the
second buffer is inbound.
Add support for warning the user if the busdma code
comes back with more buffers than will work for the
command. This will, for example, help the user
determine why an SMP command failed if busdma comes
back with three buffers.
mps_pci.c: Add sys/uio.h.
mps_sas.c: Add the SAS address and the parent handle to the
list of fields we pull from device page 0 and cache
in struct mpssas_target. These are needed for SMP
passthrough.
Add support for the XPT_SMP_IO CCB. For now, this
CCB is routed to the addressed device if it supports
SMP, or to its parent if it does not and the parent
does. This is necessary because CAM does not
currently support SMP-only nodes in the topology.
Make SMP passthrough support conditional on
__FreeBSD_version >= 900026. This will make it
easier to MFC this change to the driver without
MFCing the CAM changes as well.
mps_user.c: Un-staticize mpi_init_sge() so we can use it for
the SMP passthrough code.
mpsvar.h: Add a uio and iovecs into struct mps_command for
SMP passthrough commands.
Add a cm_max_segs field to struct mps_command so
that we can warn the user if busdma comes back with
too many segments.
Clear the cm_reply when a command gets freed. If
it is not cleared, reply frames will eventually get
freed into the pool multiple times and corrupt the
pool. (This fix is from scottl.)
Add a prototype for mpi_init_sge().
sys/param.h: Bump __FreeBSD_version to 900026 for the for the
inclusion of the XPT_GDEV_ADVINFO and XPT_SMP_IO
CAM CCBs.
versions of FreeBSD. In fact we are already missing a lot of conditional
code necessary to support older versions of FreeBSD, including alternatives
for vital functionality not yet provided by the respective subsystem back
then (see for example r199663). So this change shouldn't actually break
this driver on versions of FreeBSD that were supported before. Besides,
this driver also isn't maintained as an multi-release version outside of
the main repository, so removing the conditional code shouldn't be a
problem in that regard either.
- Sprinkle some more const on tables.
hence existing applications like webcamd are expecting that.
This problem was introduced by SVN change 214221 where cdev=
was replaced by ugen= by accident. Solve this problem by
redefining cdev= in devd notifications.
MFC after 3 days.
Approved by: thompsa (mentor)
i.e. alignment, max_address, max_iosize and segsize (only max_address is
thought to have an negative impact regarding this issue though), after
calling ata_dmainit() either directly or indirectly so these values have
no effect or at least no effect on the DMA tags and the defaults are used
for the latter instead. So change the drivers to set these parameters
up-front and ata_dmainit() to honor them.
Reviewd by: mav
MFC after: 1 month
- This adds a VM SRIOV interface, ixv, it is however
transparent to the user, it links with the ixgbe.ko,
but when ixgbe is loaded in a virtualized guest with
SRIOV configured this will be detected.
- Sync shared code to latest
- Many bug fixes and improvements, thanks to everyone
who has been using the driver and reporting issues.
the dev.fxp.%d.noflow tunable as the same effect can now be achieved with
ifconfig(8) by setting the flowcontrol media option as desired (besides
the tunable never having a chance to actually enable flow control support
so far).
In joint forces with: yongari
- Fix a bug where TCO_BOOT_STS was supposed to be cleared after
TCO_SECOND_TO_STS and not before.
Sponsored by: Sandvine Incorporated
Submitted by: Mark Johnston <mjohnston at sandvine dot com>
Reviewed by: des
MFC after: 10 days
support multi-queue but the hardware limitation made it hard to
implement supporting multi-queue. Allocating more than necessary
vectors is resource waste and it can be added back when we
implement multi-queue support.
number of retry to be performed whenever controller found RX
descriptor was empty. RX empty interrupt is generated only when the
retry counter is over. Experimentation shows retrying RX descriptor
loading increased number of dropped frames under flow-control
enabled environments so disable it and have controller generate RX
empty interrupt as fast as it can.
While I'm here fix RXCSR_DESC_RT_CNT macro.
(wrong unit number for a host controller) when the module is load /
unloaded repeatly. Attaching the USB pf is moved to usbus device's
attach.
Pointed by: yongari
disable ASPM L0S and L1 LINK states on 82573, 82574,
and 82583. The theory is that this is behind certain
hangs being experienced by some customers.
Also included a small optimization in the rxeof routine
that was in my internal code.
Change the PBA size for pchlan, it was incorrect.
MFC after: 3 days
- Fixes from John Baldwin: vlan shadow tables made per/interface,
make vlan hw setup only happen when capability enabled, and
finally, make a tuneable interrupt rate. Thanks John!
- Tweaked watchdog handling to avoid any false positives, now
detection is in the TX clean path, with only the final check
and init happening in the local timer.
- limit queues to 8 for all devices, with 82576 or 82580 on
larger machines it can get greater than this, and it seems
mostly a resource waste to do so. Even 8 might be high but
it can be manually reduced.
- use 2k, 4k and now 9k clusters based on the MTU size.
- rework the igb_refresh_mbuf() code, its important to
make sure the descriptor is rewritten even when reusing
mbufs since writeback clobbers things.
MFC: in a few days, this delta needs to get to 8.2
Shorten the descriptive strings for Huawei devices. The vendor or
operator name should not be included in the device name.
Submitted by: Emile Coetzee
MFC after: 3 days
