constraints on the rman and reject attempts to manage a region that is out
of range.
- Fix various places that set rm_end incorrectly (to ~0 or ~0u instead of
~0ul).
- To preserve existing behavior, change rman_init() to set rm_start and
rm_end to allow managing the full range (0 to ~0ul) if they are not set by
the caller when rman_init() is called.
disk dumping.
With the option SW_WATCHDOG on, these operations are doomed to let
watchdog fire, fi they take too long.
I implemented the stubs this way because I really want wdog_kern_*
KPI to not be dependant by SW_WATCHDOG being on (and really, the option
only enables watchdog activation in hardclock) and also avoid to
call them when not necessary (avoiding not-volountary watchdog
activations).
Sponsored by: Sandvine Incorporated
Discussed with: emaste, des
MFC after: 2 weeks
* enable 11n
* add ath_ahb so the AHB<->ath glue is linked in
* disable descriptor order swapping, it isn't needed here
* disable interrupt mitigation, it isn't supported here
device in /dev/ create symbolic link with adY name, trying to mimic old ATA
numbering. Imitation is not complete, but should be enough in most cases to
mount file systems without touching /etc/fstab.
- To know what behavior to mimic, restore ATA_STATIC_ID option in cases
where it was present before.
- Add some more details to UPDATING.
stack. It means that all legacy ATA drivers are disabled and replaced by
respective CAM drivers. If you are using ATA device names in /etc/fstab or
other places, make sure to update them respectively (adX -> adaY,
acdX -> cdY, afdX -> daY, astX -> saY, where 'Y's are the sequential
numbers for each type in order of detection, unless configured otherwise
with tunables, see cam(4)).
ataraid(4) functionality is now supported by the RAID GEOM class.
To use it you can load geom_raid kernel module and use graid(8) tool
for management. Instead of /dev/arX device names, use /dev/raid/rX.
bus driver at detach, hence ehci_detach() does exactly this since r199718.
Submitted by: Luiz Otavio O Souza
MFC after: 7 days
Approved by: thompsa (mentor)
levels. TX would hang, RX wouldn't. A bit of digging showed the interface
send queue was full, but IFF_DRV_OACTIVE was clear and the hardware TX
queue was empty.
It turns out that there wasn't a check to drain the interface send
queue once hardware TX had completed, so if the interface send queue
had filled up in the meantime, subsequent packets would be dropped
by the higher layers and if_start (and thus arge_start()) would never
be called.
The fix is simple - call arge_start_locked() in the software interrupt
handler after the hardware TX queue has been handled or a TX underrun
occured. This way the interface send queue gets drained.
This is a MIPS4KC CPU with various embedded peripherals, including
wireless and ethernet support.
This commit includes the platform, UART, ethernet MAC and GPIO support.
The interrupt-driven GPIO code is disabled for now pending GPIO changes
from the submitter.
Submitted by: Aleksandr Rybalko <ray@dlink.ua>
offset in the flash.
Some devices (eg the TPLink WR-1043ND) don't have a flash environment
partition which can be queried for the current board settings.
This particular workaround allows for image creators to use a hint
to set the base MAC address. For example:
hint.arge.0.eeprommac=0x1f01fc00
Introduce the AHB glue for Atheros embedded systems. Right now it's
hard-coded for the AR9130 chip whose support isn't yet in this HAL;
it'll be added in a subsequent commit.
Kernel configuration files now need both 'ath' and 'ath_pci' devices; both
modules need to be loaded for the ath device to work.
just for Redboot.
At some point we're going to need to build options for different
boot environments - for example, the UBoot setups I've seen simply
have the MAC address hard-coded at a fixed location in flash.
The OpenWRT support simply yanks the if_arge MAC directly from that
in code, rather than trying to find a uboot environment to pull it
from.
memory detected from Redboot, or overrides the "otherwise" case
if no Redboot information was found.
Some AR71XX platforms don't use Redboot (eg TP-LINK devices using
UBoot; some later Ubiquiti devices which apparently also use
UBoot) and at least one plain out lies - the Ubiquiti LS-SR71A
Redboot says there's 16mb of RAM when in fact there's 32mb.
A more "clean" solution will be needed at a later date.
The AR913x/AR724x USB lives at a different offset to the AR71xx
USB, so this needs to be either adjusted for in a subsequent
commit, or updated in hints for kernels compiled for those
platforms.
Submitted by: Luiz Otavio O Souzau <loos.br@gmail.com>
configurations and make it opt-in for those who want it. LINT will
still build it.
While it may be a perfect win in some scenarios, it still troubles users
(see PRs) in general cases. In addition we are still allocating resources
even if disabled by sysctl and still leak arp/nd6 entries in case of
interface destruction.
Discussed with: qingli (2010-11-24, just never executed)
Discussed with: juli (OCTEON1)
PR: kern/148018, kern/155604, kern/144917, kern/146792
MFC after: 2 weeks
explicit process at fork trampoline path instead of eventhadler(schedtail)
invocation for each child process.
Remove eventhandler(schedtail) code and change linux ABI to use newly added
sysvec method.
While here replace explicit comparing of module sysentvec structure with the
newly created process sysentvec to detect the linux ABI.
Discussed with: kib
MFC after: 2 Week
- Use vm_paddr_t for pa in pmap_steal_memory()
- Use uintmax_t and %jx to ensure that physical address are printed
correctly in cpu_startup() and pmap_bootstrap()
a number of cores, this allows for a sparse set of CPUs. Implement support
for sparse core masks on Octeon.
XXX jeff@ suggests that all_cpus should include cores that are offline or
running other applications/OSes, so the platform API should be further
extended to allow us to set all_cpus to include all cores that are
physically-present as opposed to only those that are running FreeBSD.
Submitted by: Bhanu Prakash (with modifications)
Reviewed by: jchandra
Glanced at by: kib, jeff, jhb
o) Have mips_wblush just do syncw, not sync on Cavium Octeon.
o) Add support for reading and writing some Octeon-specific registers.
NB: Some of these are not entirely Octeon-specific.
Submitted by: Bhanu Prakash
should_yield(). Use this in various places. Encapsulate the common
case of check-and-yield into a new function maybe_yield().
Change several checks for a magic number of iterations to use
should_yield() instead.
MFC after: 1 week
- Provide trivial implementation of sf_buf_alloc(), sf_buf_free(),
sf_buf_kva() and sf_buf_page() using direct map for n64.
- uio_machdep.c - use macros so that the direct map will be used in
case of n64.
Reviewed by: imp (earlier version)
Obtained from: jmallett (user/jmallett/octeon)
