Make sure { on the same line as struct for all struct *devdesc. Move
some type definitions to next to the dv_type define, since that's what
sets the d_type.
The gcc 7 does check for switch statement fall through cases, and if legit,
such complaint can besilenced by /* FALLTHROUGH */ comment. Unfortunately
such comment is quite limited, but will still notify the reader.
This patch is backport from illumos, see
https://www.illumos.org/rb/r/941/
Reviewed by: eadler
Differential Revision: https://reviews.freebsd.org/D14663
Make sure the periph lock is held around rmw access to softc data,
espeically flags, including work flags in iosched.
Add asserts for the periph lock where it should be held.
PR: 226510
Sponsored by: Netflix
Differential Review: https://reviews.freebsd.org/D14456
ip_reass() expects IPv4 packet and will just corrupt any IPv6 packets
that it gets. Until proper IPv6 fragments handling function will be
implemented, pass IPv6 packets to next rule.
PR: 170604
MFC after: 1 week
This matches a convention that we use, at least in ubldr, to prefix
getc/putc with a loader-specific prefix to avoid collisions. This was
encountered while trying to build the beri loader with MK_LOADER_LUA=yes.
No objection from: brooks
Reported by: emaste
from the i8254 driver when I created separate mutexes for each. The i8254
driver could be the active timecounter, leading to recursion during mutex
profiling, but the atrtc driver cannot be a timecounter, so it isn't needed.
128k and receive buffer size to 2MB. In case if system has bigger
default values, do not lower them.
This should partially solve the problem, when setkey(8) returns
EAGAIN error on systems with many SAs or SPs.
PR: 88336
Obtained from: NetBSD/ipsec-tools
MFC after: 2 weeks
o count in_nomem counter when we have failed to allocate mbuf for
promisc socket;
o count in_msgtarget counter when we have secussfully sent data to socket;
o Since we are sending messages in a loop, returning error on first fail
interrupts the loop, and all remaining sockets will not receive this
message. So, do not return error when we have failed to send data to ALL
or REGISTERED target. Return error only for KEY_SENDUP_ONE case. Now,
when some socket has overfilled its receive buffer, this will not break
other sockets.
MFC after: 2 weeks
un-function-like RTC_LOCK/UNLOCK macro usage into normal function calls.
Since there is no longer any need to handle register access from a debugger
context, those function calls can just be regular mutex lock/unlock calls.
Requested by: bde
As indicated in Committers guide Chapter 6, point 9
"Optional: Update Ports with Personal Information"
Approved by: tcberner
Differential Revision: https://reviews.freebsd.org/D14653
command handler which provided much the same information. Removing the
possibility of accessing the hardware regs from the debugger context
paves the way for simplifying the locking code in the driver.
Nothing uses the #define's values or the types. (Some NTP code does use
an audio_info_t, but it is in #ifdef'd support for Solaris and is not
this audio_info_t).
Sponsored by: DARPA, AFRL
For each regulators create an hw.regulator.<regname>. :
uvolt: Current value
always_on: 1 If the reg is always on
boot_on: 1 If the reg is set at boot time
enable_cnt: Number of consumer(s)
enable_delay: Delay before enabling the regulator
ramp_delay: The Ramp delay
max_uamp: The maximum value of the regulator in uAmps
min_uamp: The minimal value of the regulator in uAmps
max_uvolt: The maximum value of the regulator in uVolts
min_uvolt: The minimal value of the regulator in uVolts
Reviewed by: ian
Differential Revision: https://reviews.freebsd.org/D14578
These parameters may be changed via ifconfig(8); by default,
mgt / mcast rates are lowest possible and ucast rate is not set
(matches previous configuration).
While here, store some variables locally for better readability.
The vfs.mountroot.timeout tunable and .timeout directive in a mount.conf(5)
file allow specifying a wait timeout for the device(s) hosting the root
filesystem to become usable. The current mechanism for waiting for devices
and detecting their availability can't be used for zfs-hosted filesystems.
See the comment #20 in the PR for some expanded detail on these points.
This change adds retry logic to the actual root filesystem mount. That is,
insted of relying on device availability using device name lookups, it uses
the kernel_mount() call itself to detect whether the filesystem can be
mounted, and loops until it succeeds or the configured timeout is exceeded.
These changes are based on the patch attached to the PR, but it's rewritten
enough that all mistakes belong to me.
PR: 208882
X-MFC after: sufficient testing, and hopefully in time for 11.1
this check on open, but "iscsictl -M", or an iSCSI redirect received by
iscsid(8) could end up with two sessions with the same target name and
portal.
MFC after: 2 weeks
