our own watchdog that piggybacks on the em_local_timer() routine.
We suppose that the if_timer/if_watchdog interface should be
obsoleted, since it doesn't fit the modern SMP network stack.
NIC drivers should create their own watchdogs, that check and
clear the timers always holding driver's lock.
In collaboration with: jfv, scottl
- Only call iwi_stop() if we got far enough along in iwi_attach() to
alloc an ifnet.
- Release the firmware after stopping the interface and detaching the
ifnet.
MFC after: 1 month
Reviewed by: sam
to be switched to is saved in sc->delayed_next_scr and
the actual switch is performed later. It was possible
to get into the endless loop when attempting to switch
to a closed vty (which is not allowed and beep-alerted
when attempted) and when the visual beep was in effect.
This caused sc->delayed_next_scr to never be reset and
endless attempts to switch to a closed vty and endless
visual beeping. How to repeat:
- boot into single-user
- run "kbdcontrol -b visual"
- quickly press Alt+F2 two times
PR: kern/68016
X-MFC after: 6.2-RELEASE
specific privilege names to a broad range of privileges. These may
require some future tweaking.
Sponsored by: nCircle Network Security, Inc.
Obtained from: TrustedBSD Project
Discussed on: arch@
Reviewed (at least in part) by: mlaier, jmg, pjd, bde, ceri,
Alex Lyashkov <umka at sevcity dot net>,
Skip Ford <skip dot ford at verizon dot net>,
Antoine Brodin <antoine dot brodin at laposte dot net>
as we have no use for that info. Instead let this function return the
keyboard ID and verify at its invocation in sunkbd_configure() that we're
talking to a Sun type 4/5/6 keyboard, i.e. a keyboard supported by this
driver.
- Add an option SUNKBD_EMULATE_ATKBD whose code is based on the respective
code in ukbd(4) and like UKBD_EMULATE_ATSCANCODE causes this driver to
emit AT keyboard/KB_101 compatible scan codes in K_RAW mode as assumed by
kbdmux(4). Unlike UKBD_EMULATE_ATSCANCODE, SUNKBD_EMULATE_ATKBD also
triggers the use of AT keyboard maps and thus allows to use the map files
in share/syscons/keymaps with this driver at the cost of an additional
translation (in ukbd(4) this just is the way of operation).
- Implement an option SUNKBD_DFLT_KEYMAP, which like the equivalent options
of the other keyboard drivers allows to specify the default in-kernel
keyboard map. For obvious reasons this made to only work when also using
SUNKBD_EMULATE_ATKBD.
- Implement sunkbd_check(), sunkbd_check_char() and sunkbd_clear_state(),
which are also required for interoperability with kbdmux(4).
- Implement K_CODE mode and FreeBSD keypad compose.
- As a minor hack define KBD_DFLT_KEYMAP also in the !SUNKBD_EMULATE_ATKBD
case so we can obtain fkey_tab from <dev/kbd/kbdtables.h> rather than
having to duplicate it and #ifdef some more code.
- Don't use the TX-buffer for writing the two command bytes for setting the
keyboard LEDs as this consequently requires a hardware FIFO that is at
least two bytes in depth, which the NMOS-variant of the Zilog SCCs doesn't
have. Thus use an inlined version of uart_putc() to consecutively write
the command bytes (a cleaner approach would be to do this via the soft
interrupt handler but that variant wouldn't work while in ddb(4)). [1]
- Fix some minor style(9) bugs.
PR: 90316 [1]
Reviewed by: marcel [1]
BIO_READ/BIO_WRITE is sent to vnode-backed provider (BIO_DELETE or
BIO_FLUSH).
Reported by: ceri
Add support for BIO_FLUSH to vnode-backed md(4) devices based on
VOP_FSYNC().
- Test the mac_type rather than if_hwassist (since ifp doesn't exist yet)
to determine if the adapter supports TSO and thus to change the sizes
for the bus_dma tag.
Reviewed by: glebius
during detach() similar to other NIC drivers rather than allocating them
during init() and freeing them during stop():
- Move creation of tx bus_dma tag amd maps and tx_buffer_area from
em_setup_transmit_structures() to em_allocate_transmit_structures().
- Call em_allocate_xxx_structures() in em_attach().
- Only call em_free_xxx_structures() in em_detach().
- Change em_setup_xxx_structures() to free any existing tx or rx buffers
and in the case of rx repopulate the ring with newer buffers.
Reviewed by: jfv
the EOP descriptor in the first descriptor of the packet. And then
in em_txeof() search for DD bits set only in the EOP descriptors,
embedding the cleanup of all packet's descriptors into inner loop.
This change is important for future chips, where DD bit is going
to be set only on the EOP descriptors.
Submitted by: jfv
Details:
o if_em.c changes:
- Added several new PCI ids.
- Check em_check_phy_reset_block() before doing SIOCSIFMEDIA ioctl.
- Don't touch TARC registers, they are now handled in shared
code in if_em_hw.c.
- Move RDH and RDT setting to the end of
em_initialize_receive_unit().
- Declare em_read_pcie_cap_reg(), now empty.
o if_em_hw.c dropped in from vendor, then restored rev. 1.15.
o if_em_hw.h dropped in from vendor, then modified:
- Added RX overrun interrupt flag to interrupt enable mask.
- Remove declarations of em_io_read(), em_io_write().
Approved by: jfv
the CAM_NEW_TRAN_CODE that has been in the tree for some years now.
This first step consists solely of adding to or correcting
CAM_NEW_TRAN_CODE pieces in the kernel source tree such
that a both a GENERIC (at least on i386) and a LINT build
with CAM_NEW_TRAN_CODE as an option will compile correctly
and run (at least with some the h/w I have).
After a short settle time, the other pieces (making
CAM_NEW_TRAN_CODE the default and updating libcam
and camcontrol) will be brought in.
This will be an incompatible change in that the size of structures
related to XPT_PATH_INQ and XPT_{GET,SET}_TRAN_SETTINGS change
in both size and content. However, basic system operation and
basic system utilities work well enough with this change.
Reviewed by: freebsd-scsi and specific stakeholders
only those bars that had addresses assigned by the BIOS and where the
bridges were properly programmed. Now even unprogrammed ones work.
This was needed for sun4v. We still only implement up to 2GB memory
ranges, even for 64-bit bars. PCI standards at least through 2.2 say
that this is the max (or 1GB is, I only know it is < 32bits).
o Always define pci_addr_t as uint64_t. A pci address is always 64-bits,
but some hosts can't address all of them.
o Preserve the upper half of the 64-bit word during resource probing.
o Test to make sure that 64-bit values can fit in a u_long (true on some
platforms, but not others). Don't use those that can't.
o minor pedantry about data sizes.
o Better bridge resource reporting in bootverbose case.
o Minor formatting changes to cope with different data types on different
platforms.
Submitted by: jmg, with many changes by me to fully support 64-bit
addresses.
Though it is named after overclocking tool for ASUS motherboards,
it is not capable to change clock ratio or CPU core voltage.
This driver exports Templature, Power output voltage, Fan RPM under
dev.acpi_aiboost.0.*.
Descriptions for these values are set to sysctl describe, which can be
get by sysctl -d.
in #ifdef __NO_STRICT_ALIGNMENT rather than #ifdef __i386__. This
means that amd64 now also uses the optimized code. [1]
While at it, fix a nearby style(9) bug.
- Remove the hw.dc_quick SYSCTL, which allowed to turn off the above
mentioned optimization, as like the equivalent and already removed
- In dc_setcfg() suppress printing a warning when forcing the receiver
and transceiver to idle state times out for chips where the status
bits in question just never change (observed in detail with DM9102A)
and therefore the warning would be highly likely false positive. [2]
- In dc_ifmedia_sts() add a missing DC_UNLOCK().
Tested by: Hans-Joerg Sirtl on amd64 [1]
PR: 82681 [2]
Obtained from: NetBSD tlp(4) [2]
MFC after: 1 week
Rename MAX_SAMPLE_RATES macro to OSS_MAX_SAMPLE_RATES. The old
macro clashed with those used in other applications and libaries
(ex: RtAudio). 4Front responded by updating their spec, so we
will follow suit.
Submitted by: ryanb
Noticed by: pointyhat/kris
new device support, and it is hoped a more stable driver for 6.2. RELEASE.
This checkin was discussed and approved today by RE, scottl, jhb, and pdeuskar
keyboard is attached only after the system has already booted.
If USB keyboard is also present, and there's no kbdmux(4), the problem
has been hiding itself because as soon as we get to multi-user, the
USB keyboard becomes an active keyboard (see devd.conf), thus marking
atkbd inactive and letting the old code initialize the keyboard.
With kbdmux(4), or if there's no USB keyboard, the atkbd keyboard is
always active, whether it's physically attached or not, thus it never
initialized itself properly on a physical attach.
To fix this, move block that initialized the keyboard on attach upper
so it doesn't depend on the (KBD_IS_ACTIVE(kbd) && KBD_IS_BUSY(kbd))
condition. Also move KBD_FOUND_DEVICE() a few lines upper so that
KDSETLED and KDSETREPEAT that follow it propagate to the controller.
MFC after: 3 days
: revision 1.27
: date: 2000/05/28 12:43:24; author: ache; state: Exp; lines: +3 -2
: Manipulate with AltGR Led (really CapsLock Led) only in K_XLATE mode, because
: all other modes not set ALKED flag and it means that CapsLock always turned
: off for them.
: Real bug example is X11 which never turn on CapsLock with Russian keyboard.
:
: PR: 18651
: Submitted by: "Mike E. Matsnev" <mike@po.cs.msu.su>
MFC after: 3 days
and TCP checksum offloading fine, it only has a problem with IP checksums on
IP fragments.. Barring a fix or workaround available from the hardware, the
real solution would be to have finer grained control in the stack over what
can and cannot be assisted in hardware.
yet to be investigated circumstances. If that happens truncate to the number
of rates that the firmware supports.
Found by: Jeremie Le Hen
Obtained from: OpenBSD (w/ changes)
MFC after: 3 days
kept unused in the ring. This check should probably be moved up to
bce_start_locked at some point, as it'll make the loop up there slightly
more efficient, and will eliminate a costly set of busdma operations when
the ring is full. But this works for now.
This makes all of my UDP torture tests work. I'll cautiously say that
it might even work for other users now. Feedback is appreciated.
If the length is zero, catch this early, instead of making dflen go negative
and letting bad things happen... We also check to see if RV (checksum) is
0, and handle that has a checksum failure...
Properly handle checksum failures by not processing read-write VPD data,
and removing all the found read-only data...
Tested by: oleg (dflen going negative)
should be easily adapted to SD 2.0 (aka SDHC), SDIO, MMC and MMCplus
cards. At the present time, there's only one bridge driver for the
ARM9 based Atmel AT91RM9200.
tasks. Since the host controllers rely on tasks to process transfer
timeouts, if a synchronous transfer from a driver was invoked from
a task and timed out, it would never complete because the single
task thread was stuck performing the synchronous transfer so couldn't
process the timeout.
This affected the axe, udav and ural drivers.
Problem hardware provided by: guido
long being DMA'ed 2 (or 1) bytes past the end of the mbuf and corrupting
random kernel memory. I had forgotten about the 2 bytes of implict
padding the firmware assumes.
Sponsored by: Myricom Inc.
- Fix the locking protocol to eliminate races between normal I/O and AENs.
- Various small improvements and usability tweaks.
Sponsored by: IronPort
Portions Submitted by: Doug Ambrisko
- Use bus_dmamap_load_mbuf_sg() to eliminate the need for the callback and
all of the extra bookkeeping associated with it.
- Eliminate the bce_dmamap_arg structure and streamline the memory allocation
routines to not need it. This does change some of the debugging messages.
- Refactor the loop that fills the buffer descriptor so that it can be done
with a single set of logic in a single loop instead of two sets of logic.
- Eliminate the need to cache and pass descriptor indexes between the start
loop and the encap function.
- Change the start loop to always check the ifnet sendq for more work.
This significantly helps the driver withstand large UDP workloads, though
it's still not perfect. I suspect the remaining work lies with handling
the OACTIVE flag, and also in possibly streamlining the interrupt handler
some. It is, however, nearly on par with the other popular gigabit drivers
in terms of stability now.
- Add entries in the uscanner.4 man page (along with missing 3500).
PR: usb/100957 [1], usb/100992 [2]
Submitted by: Jim Teresco <terescoj@teresco.org> [1],
Walter C. Pelissero <walter.pelissero@iesy.net> [2]
MFC after: 3 days
will fix a problem where you boot w/ the default of autoselect, but then
set the speed to 100/full, the switch will keep the autoselect/100/full
negotiation... This will continue to work till someone resets the switch
or unplugs the cable resulting in the switch failing to autoneg and falling
back to 100/half, causing a hard to track down duplex mismatch..
Submitted by: nCircle Network Security, Inc.
MFC after: 1 week
- Add support for the Conexant Waikiki/CX20551-22, found
in most Toshiba P100 series laptops. Despite of growing
urban legend of "unsupported Conexant", this codec is fully
supported in this driver.
Note: Toshiba P100 has broken (acpi) BIOS, thus rendering
its soundchip useless. Please disable ACPI, or get
BIOS updates (if any).
Found/tested by: Vulpes Velox <v.velox@vvelox.net>
URL: http://lists.freebsd.org/pipermail/freebsd-multimedia/2006-September/004896.html
- Parser cleanups to handle possible oss/mixer collision. Found
after parsing Conexant Waikiki nodes.
- Increase resilient against resource failure during attach/detach.
- Implement simple config through hint.pcm.<unit>.config. Supported
options:
gpio0 (default on Acer), gpio1, gpio2, softpcmvol,
fixedrate (default), forcestereo (default)
* Option prefixed with "no" (such as "nofixedrate") will do
the opposite.
* Options can be separated using space " " or comma ",".
* The "no" option will take precedence over anything else.
Example:
hint.pcm.0.config="gpio2,nofixedrate,noforcestereo,nogpio0,softpcmvol"
hint.pcm.0.config="softpcmvol noforcestereo"
or not the OS has to wait for RX_RDY or TX_RDY to be set before the OS sets
the control code in the control/status register. Looking at the interface
design, it seems that RX_RDY and TX_RDY are probably there to protect
access to the data register and have nothing to do with the control/status
register. Nevertheless, try to take what I think is the more conservative
approach and always wait for the appropriate [TR]X_RDY flag to be set
before writing any of the WR_NEXT, WR_END, RD_START, or RD_NEXT control
codes to the control/status register.
close and re-open the default pipe instead of relying on the host
controller driver to notice the changes. Remove the unreliable code
that attempted to update these fields while the pipe was active.
This fixes a case where the hardware could cache and continue to
use the old address, resulting in a "getting first desc failed"
error.
PR: usb/103167
- Fix support for ASUS M5200ae (buggy BIOS)
- Fix few problems, reported by Coverity Prevent (TM).
CID: 246991, 246676, 246675, 246674, 246477
Found by: Coverity Prevent (TM)
The parallel LINT build sometimes broke if kernel-depend wasn't
fast enough in generating ukbdmap.h. If someone thinks this
option would still be useful for the module, a proper fix is
to add the code generating ukbdmap.h into modules/ukbd/Makefile
and backing this change out.
Add support for Intel High Definition Audio Controller.
This driver make a special guarantee that "playback" works
on majority hardwares with minimal or without specific vendor
quirk.
This driver is a product of collaborative effort made by:
Stephane E. Potvin <sepotvin@videotron.ca>
Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Wesley Morgan <morganw@chemikals.org>
Daniel Eischen <deischen@FreeBSD.org>
Maxime Guillaud <bsd-ports@mguillaud.net>
Ariff Abdullah <ariff@FreeBSD.org>
....and various people from freebsd-multimedia@FreeBSD.org
Refer to snd_hda(4) for features and issues.
Welcome To HDA.
Sponsored by: Defenxis Sdn. Bhd.
This driver make a special guarantee that "playback" works
on majority hardwares with minimal or without specific vendor
quirk.
This driver is a product of collaborative effort made by:
Stephane E. Potvin <sepotvin@videotron.ca>
Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Wesley Morgan <morganw@chemikals.org>
Daniel Eischen <deischen@FreeBSD.org>
Maxime Guillaud <bsd-ports@mguillaud.net>
Ariff Abdullah <ariff@FreeBSD.org>
....and various people from freebsd-multimedia@FreeBSD.org
Refer to snd_hda(4) for features and issues.
Welcome To HDA.
Sponsored by: Defenxis Sdn. Bhd.
- fix multiple initialization of the first codec (support for more than
one codec should be added in the future)
- use spicds instead of ak452x module
Submitted by: "Konstantin Dimitrov" <kosio.dimitrov@gmail.com>
stripping was disabled due to being in promisc mode. This is a hardware
bug. Update comment to explicitly state the reason the manual vlan tag
insertion in this case. See rev. 1.53 for further information as well.
Noticed by: jhb
generic vlan_start() takes care of it when vlan hardware insertion is disabled.
In em_set_promisc() add a note that BPF may also be enabled without going into
promisc mode.
Reviewed by: jfv
IP options and add skeleton IPv6 support. The new code structure can also be
easily enhanced to support new/more protocols (SCTP) in the future.
Reviewed by: jfv
and add skeleton IPv6 support. The new code structure can also be easily
enhanced to support new/more protocols (SCTP) and IP fragmentation in the
future.
In em_encap() only try to do TSO if 'dotso' is true.
Reviewed by: jfv
- EFBIG means the mbuf chain was too long and bus_dma ran out of segments.
Defragment the mbuf chain and try again. (Already existed, not changed.)
- ENOMEM means bus_dma could not obtain enough bounce buffers at this point
in time. Defer sending and try again later.
- All other errors, in particular EINVAL, are fatal and prevent the mbuf
chain from ever going through. Drop it and report error.
- Checking (nsegs == 0) is unnecessary as bus_dmamap_load_mbuf_sg() always
reports an error if it is < 1.
This prevents broken packets from clogging the interface queue indefinately.
Discussed with: scottl
Reviewed by: jfv
commit.
1) sys/dev/sound/pcm/sound.h
sys/dev/sound/pcm/channel.c
* Be more specific: SD_F_SOFTVOL -> SD_F_SOFTPCMVOL
2) sys/dev/sound/pcm/mixer.[ch]
* Implement
mix_setparentchild()
mix_setrealdev()
mix_getparent()
mix_getchild()
The purpose of these functions is implement relative volume
adjustment, such as to tie two or more mixer device into a
single logical device. Usefull for the upcoming HDA driver
and few AC97 codec (such as AD1981B) where the master volume
"vol" need to be implemented using this logical manner.
3) sys/dev/sound/pcm/ac97_patch.[ch]
* Patch for AD1981B codec to enable (automuting) headphone jack sense.
4) sys/dev/sound/pcm/ac97.c
* Implement proper logical master volume for AD9181B codec
through various mix_set{parentchild,realdev}(). Tie both
"ogain" (headphone volume) and "phone" (speaker/lineout) to
a logical "vol".
5) sys/dev/sound/pcm/usb/uaudio_pcm.c
* ditto, for "vol" -> { "pcm" }.
MFC after: 1 month
ioctls passing integer arguments should use the _IOWINT() macro.
This fixes a lot of ioctl's not working on sparc64, most notable
being keyboard/syscons ioctls.
Full ABI compatibility is provided, with the bonus of fixing the
handling of old ioctls on sparc64.
Reviewed by: bde (with contributions)
Tested by: emax, marius
MFC after: 1 week
The key problem was that the aperture size detection using the MSAC bit
doesn't work -- the bit appears to be set even when it shouldn't be. Linux
takes a different approach, testing for a bit of the GMADR (PCIR_BAR(2)) being
set. However, as I don't think that's a safe way to test aperture size, we
just allocate the resource and check its size. This also pointed out that
agp_generic_attach hadn't been allocating our aperture resource, which may
have caused problems in some cases.
Also corrected is a minor copy-and-pasteo in an error case.
PR: kern/103079
Submitted by: mnag
Tested on: i945GM, i915GM
MFC after: 2 weeks
The goal was to sync with the OSSv4 API 4Front Technologies uses in their
proprietary OSS driver. This was successful as far as possible. The part
of the API which is stable is implemented, for the rest there are some
stubs already.
New system ioctls:
- SNDCTL_SYSINFO - obtain audio system info (version, # of audio/midi/
mixer devices, etc.)
- SNDCTL_AUDIOINFO - fetch details about a specific audio device
- SNDCTL_MIXERINFO - fetch details about a specific mixer device
New audio ioctls:
- Sync groups (SNDCTL_DSP_SYNCGROUP/SNDCTL_DSP_SYNCSTART) which allow
triggered playback/recording on multiple devices (even across processes
simultaneously).
- Peak meters (SNDCTL_DSP_GETIPEAKS/SNDCTL_DSP_GETOPEAKS) - can query
audio drivers for peak levels (needs driver support, disabled for now).
- Per channel playback/recording levels -
SNDCTL_DSP_{GET,SET}{PLAY,REC}VOL. Note that these are still in name
only, just wrapping around the AC97-style mixer at the moment. The next
step is to push them down to the drivers.
Audio ioctls still under development by 4Front (for which stubs may exist
in this commit):
- SNDCTL_GETNAME, SNDCTL_{GET,SET}{SONG,LABEL}
- SNDCTL_DSP_{GET,SET}_CHNORDER
- SNDCTL_MIX_ENUMINFO, SNDCTL_MIX_EXTINFO - (might be documented enough in
the OSS releases to work on this. These ioctls cover the cool "twiddle
any knob on your card" features.)
Missing:
- SNDCTL_DSP_COOKEDMODE -- this ioctl is used to give applications direct
access to a card's buffers, bypassing the feeder architecture. It's
a toughy -- "someone" needs to decide :
(a) if this is desireable, and (b) if it's reasonably feasible.
Updates for driver writers:
So far, only two routines to the channel class (in channel_if.m) are added.
One is for fetching a list of discrete supported playback/recording rates
of a channel, and the other is for fetching peak level info (useful for
drawing peak meters). Interested parties may want to help pushing down
SNDCTL_DSP_{GET,SET}{PLAY,REC}VOL into the drivers.
To use the new stuff you need to rebuild the sound drivers or your kernel
(depending on if you use modules or not) and to install soundcard.h (a
buildworld/installworld handles this).
Sponsored by: Google SoC 2006
Submitted by: ryanb
Many thanks to: 4Front Technologies for their cooperation, explanations
and the nice license of their soundcard.h.
- Split out the communication protocols into their own files and use
a couple of function pointers in the softc that the commuication
protocols setup in their own attach routine.
- Add support for the SSIF interface (talking to IPMI over SMBus).
- Add an ACPI attachment.
- Add a PCI attachment that attaches to devices with the IPMI interface
subclass.
- Split the ISA attachment out into its own file: ipmi_isa.c.
- Change the code to probe the SMBIOS table for an IPMI entry to just use
pmap_mapbios() to map the table in rather than trying to setup a fake
resource on an isa device and then activating the resource to map in the
table.
- Make bus attachments leaner by adding attach functions for each
communication interface (ipmi_kcs_attach(), ipmi_smic_attach(), etc.)
that setup per-interface data.
- Formalize the model used by the driver to handle requests by adding an
explicit struct ipmi_request object that holds the state of a given
request and reply for the entire lifetime of the request. By bundling
the request into an object, it is easier to add retry logic to the various
communication backends (as well as eventually support BT mode which uses
a slightly different message format than KCS, SMIC, and SSIF).
- Add a per-softc lock and remove D_NEEDGIANT as the driver is now MPSAFE.
- Add 32-bit compatibility ioctl shims so you can use a 32-bit ipmitool
on FreeBSD/amd64.
- Add ipmi(4) to i386 and amd64 NOTES.
Submitted by: ambrisko (large portions of 2 and 3)
Sponsored by: IronPort Systems, Yahoo!
MFC after: 6 days
Unfortunately, the QUEUE FULL event only tells you Bus && Target.
It doesn't tell you lun. In order for the XPT_REL_SIMQ action to
work, we have to have a real lun. But which one? For now, just
iterate over MPT_MAX_LUNS.
Practically speaking, this is only going to be happening for lower
quality SAS or SATA drives behind the SAS controller, which means
only lun 0, so it's not so bad.
Helpful Reminder Nagging from: John Baldwin, Fred Whiteside
MFC after: 5 days
of the chip to let ASF/IPMI firmware to respond to IPMI after attaching
and when the chip is down. David looked at it but could really say
what they right minimal config. stuff would be. It's not documented.
I figured this out via trial and error.
Reviewed by: davidch
is incorrect, and causes endianness bugs on 64-bit big-endian
machines (sparc64), it's the best choice for now, as many of
these IOCTLs are used inside the kernel, and bogusly pass an
argument as "int *" which results in unaligned access panics
on sparc64 when attempting to dereference them via *(intptr_t *).
(Several of us are working on a real fix, which is uneasy.)
part of the hal distribution early on when the hal was built for
each os but it's been portable for a long time so move the os-specific
code out (and off the vendor branch)
o correct the copyright on ah_osdep.?; it was mistakenly given a
restricted license and not a dual-bsd/gpl license
o remove the module api definition as it was never used
o fixup include paths for move of ah_osdep.h
MFC after: 2 weeks
with other commonly used sysctl name spaces, rather than declaring them
all over the place.
MFC after: 1 month
Sponsored by: nCircle Network Security, Inc.
m_pkthdr.ether_vlan. The presence of the M_VLANTAG flag on the mbuf
signifies the presence and validity of its content.
Drivers that support hardware VLAN tag stripping fill in the received
VLAN tag (containing both vlan and priority information) into the
ether_vtag mbuf packet header field:
m->m_pkthdr.ether_vtag = vlan_id; /* ntohs()? */
m->m_flags |= M_VLANTAG;
to mark the packet m with the specified VLAN tag.
On output the driver should check the mbuf for the M_VLANTAG flag to
see if a VLAN tag is present and valid:
if (m->m_flags & M_VLANTAG) {
... = m->m_pkthdr.ether_vtag; /* htons()? */
... pass tag to hardware ...
}
VLAN tags are stored in host byte order. Byte swapping may be necessary.
(Note: This driver conversion was mechanic and did not add or remove any
byte swapping in the drivers.)
Remove zone_mtag_vlan UMA zone and MTAG_VLAN definition. No more tag
memory allocation have to be done.
Reviewed by: thompsa, yar
Sponsored by: TCP/IP Optimization Fundraise 2005
- Added support for multicast filtering, now that the firmware
supports it. Note that this is not yet tested, as multicast
seems to panic -current (even w/o mxge loaded)
- Added workaround to cope with different irq data struct size on
pre-multicast firmware which can found running on nics.
- Added Intel E5000 PCIe chipsets to list providing aligned completions.
- Replaced various magic constants with #defines, now that they are
defined in the firmware headers.
in the transmit busdma tag, so I moved the segment list off the
stack.
- Fixed transmit routine to ensure it doesn't read past the end
of an mbuf when parsing headers.
- Corrected handling of odd length segments. Setting MXGEFW_FLAGS_ALIGN_ODD
is required only when offloading the checksum of that frame.
Sponsored by: Myricom Inc.
if_watchdog, etc., or in functions used only in these methods.
In all other functions in the driver use device_printf().
- Use __func__ instead of typing function name.
Submitted by: Alex Lyashkov <umka sevcity.net>
if_ioctl, if_watchdog, etc, or in functions that are used by
these methods only. In all other cases use device_printf().
This also fixes several panics, when if_printf() is called before
softc->ifp was initialized.
Submitted by: Alex Lyashkov <umka sevcity.net>
in syscons. This replaces a simple access semaphore that was assumed to be
protected by Giant but often was not. If two threads that were otherwise
SMP-safe called printf at the same time, there was a high likelyhood that
the semaphore would get corrupted and result in a permanently frozen video
console. This is similar to what is already done in the serial console
drivers.
Instead, we want busses to explicitly specify an add_child routine if they
want to support identify routines, but by default disallow having outside
drivers add devices.
- Give smbus(4) an explicit bus_add_child() method.
Requested by: imp
- Change smbus_callback() to pass a void * rather than caddr_t.
- Change smbus_bread() to pass a pointer to the count and have it be an
in/out parameter. The input is the size of the buffer (same as before),
but on return it will contain the actual amount of data read back from
the bus. Note that this value may be larger than the input value. It
is up to the caller to treat this as an error if desired.
- Change the SMB_BREAD ioctl to write out the updated struct smbcmd which
will contain the actual number of bytes read in the 'count' field. To
preserve the previous ABI, the old ioctl value is mapped to SMB_OLD_BREAD
which doesn't copy the updated smbcmd back out to userland. I doubt anyone
actually used the old BREAD anyway as it was rediculous to do a bulk-read
but not tell the using program how much data was actually read.
- Make the smbus driver and devclass public in the smbus module and
push all the DRIVER_MODULE()'s for attaching the smbus driver to
various foosmb drivers out into the foosmb modules. This makes all
the foosmb logic centralized and allows new foosmb modules to be
self-contained w/o having to hack smbus.c everytime a new smbus driver
is added.
- Add a new SMB_EINVAL error bit and use it in place of EINVAL to return
an error for bad arguments (such as invalid counts for bread and bwrite).
- Map SMB bus error bits to EIO in smbus_error().
- Make the smbus driver call bus_generic_probe() and require child drivers
such as smb(4) to create device_t's via identify routines. Previously,
smbus just created one anonymous device during attach, and if you had
multiple drivers that could attach it was just random chance as to which
driver got to probe for the sole device_t first.
- Add a mutex to the smbus(4) softc and use it in place of dummy splhigh()
to protect the 'owner' field and perform necessary synchronization for
smbus_request_bus() and smbus_release_bus().
- Change the bread() and bwrite() methods of alpm(4), amdpm(4), and
viapm(4) to only perform a single transaction and not try to use a
loop of multiple transactions for a large request. The framing and
commands to use for a large transaction depend on the upper-layer
protocol (such as SSIF for IPMI over SMBus) from what I can tell, and the
smb(4) driver never allowed bulk read/writes of more than 32-bytes
anyway. The other smb drivers only performed single transactions.
- Fix buffer overflows in the bread() methods of ichsmb(4), alpm(4),
amdpm(4), amdsmb(4), intpm(4), and nfsmb(4).
- Use SMB_xxx errors in viapm(4).
- Destroy ichsmb(4)'s mutex after bus_generic_detach() to avoid problems
from child devices making smb upcalls that would use the mutex during
their detach methods.
MFC after: 1 week
Reviewed by: jmg (mostly)
to it. Try to co-operate with the IPMI/ASF firmware accessing the PHY.
One we get link we don't mess with the PHY. If we do then over time
the NIC will go off line. It would be nice if we could tell if IPMI
was enabled on the chip but I can't figure out a reliable way to do
that. The scheme I tried worked on a Dell PE850 but not on an HP machine.
So we assume any NIC that has ASF capability needs to deal with it.
The code was inspired by the support in Linux from kernel.org and Broadcom.
Broadcom did give me some info. but it is rather limited and is mostly
just what is in the Linux driver. Thanks to the numerous people that
helped debug the many prior versions and that I didn't break other
bge(4) HW.
Reviewed by: several people
Tested by: even more
Ever since rev 1.68 re(4) checks the validity of link in re_start.
But rlphy(4) got a garbled data due to a different bit layout used on
8139C+ and it couldn't report correct link state. To fix it, ignore
BMCR_LOOP and BMCR_ISO bits which have different meanings on 8139C+.
I think this also make dhclient(8) work on 8139C+.
Reported by: Gerrit Kuehn <gerrit AT pmp DOT uni-hannover DOT de>
Tested by: Gerrit Kuehn <gerrit AT pmp DOT uni-hannover DOT de>
is to able to be called after *all* attach and enable events are done.
We establish a SYSINIT hook to call this handler. The current usage for it
is to add scsi target resources *after* all enables are done. There seems
to be some dependencies between different halves of a dual-port with respect
to target mode.
Put in more meaningful event messages for some events- in particular
QUEUE FULL events so we can see what the queue depth was when the
IOC sent us this message.
MFC after: 1 week
- Add support for Intel 965 Express chipsets.
- Add support for R200 vertex programs, along with minor bugfixes.
- Add support for vblank synchronization to pipe B of Intel hardware
(laptop screens).
AEN. This makes the boot messages cleaner. I now know how this
structure works so I can implement it versus guessing. Remove the
not ready type code since it is ready now.
I added the time stamp/locale/class so people can parse messages better.
Create a sysctl so that we can set the locale/class level.
s/device_ptr_t/device_t/g
No md5 changes in the .o's
# Note to the md5 tracking club: $FreeBSD$ changes md5 after every commit
# so you need to checkout -kk to get $FreeBSD$ instead of the actual value
# of the keyword.
This helps systems that don't actually have atkbd controllers, such as the Intel
SBX82 blade, boot without device.hints hacks.
Hardware for this fix provided by iXsystems.
PR: 94822
Submitted by: Devon H. O'Dell <devon.odell@coyotepoint.com>
MFC After: 3 days
required by arches like sparc64 (not yet implemented) and sun4v where there
are seperate IOMMU's for each PCI bus... For all other arches, it will
end up returning NULL, which makes it a no-op...
Convert a few drivers (the ones we've been working w/ on sun4v) to the
new convection... Eventually all drivers will need to replace the parent
tag of NULL, w/ bus_get_dma_tag(dev), though dev is usually different for
each driver, and will require hand inspection...
Reviewed by: scottl (earlier version)
register. This really shouldn't be using pci_enable_io() directly as
bus_alloc_resource() does it already, but the cached copy of the
command word needs to be correct so the enable/disable mwi functions
work properly.
- Use pci bus accessors to read revision ID and subvendor IDs.
Reviewed by: jvogel
LCDs to blink in the V_DISPLAY_ON case, at least in combination with
some 13W3-VGA-adaptors (what's exactly going on is unclear though,
as it happens when all of H-sync, V-sync and video output are enabled
and not touching the sync bits from the preset fixes it). Thus
creator_blank_display() now is reduced to turning the video output
on/off.
Although that DPMS code did what the XFree86/Xorg sunffb(4x) does,
it was questionable in the first place, as both implementations
also turn(ed) off the video output on standby and suspend, thus most
likely causing the monitor to turn off instead of entering standby
or suspend as intended (at least my monitors don't).
Reported and tested by: Patrick Reich
MFC after: 3 days
Following issues should be resolved:
- random watchdog timeouts (caused by concurrent phy access)
- some link state issues
- non working TX if media type was set explicitly
PR: kern/98738
Approved by: glebius (mentor)
MFC after: 2 weeks
