time through the mbuf chain during copy and TSO limiting.
It is used by both Rack and now the FreeBSD stack.
Sponsored by: Netflix Inc
Differential Revision: https://reviews.freebsd.org/D15937
Post r335356 it is possible to have an inpcb on the hash lists that is
partially torn down. Validate before using. Also as a side effect of this
change the lock ordering issue between hash lock and inpcb no longer exists
allowing some simplification.
Reported by: pho@
Without a call to check_free_callbacks() clients waiting for grant
references would not be woken up even when there are sufficient grant
references available.
The check was likely left out as a mistake when the function was first
added.
Note that other functions used to free grant references already call
check_free_callbacks.
Submitted by: pratyush
Reviewed by: royger
Differential review: https://reviews.freebsd.org/D15899
We always install ELF Tool Chain's elfcopy as objcopy, so to avoid
confusion rename the src directory containing our reach-over Makefile
to match.
Requested by: jhb
Sponsored by: The FreeBSD Foundation
Summary: POWER8 and POWER9 use a single CPU register, per core, to change clock
speed. Everything else is handled by the on-chip controller. This change
necessitates a change to the cpufreq global kernel driver to bump supported
levels, as the device tree for these systems can have theoretically 256
different options. On my POWER9 Talos, the list consists of 100 items. At
16.67MHz intervals, that allows for a change of roughly 1.67GHz between lowest
and highest.
This has only been tested on the POWER9. However, since they're similar, this
should work on POWER8 as well.
Reviewed By: nwhitehorn
Differential Revision: https://reviews.freebsd.org/D15932
Some complexity exists in these bits that isn't needed. The sysctl handler,
upon change to '2', runs through the current set of hints and sets them in
the kenv.
However, this isn't at all necessary if we're pulling hints from the kenv,
static or dynamic, as the former will get added to the latter in
init_dynamic_kenv (see: kern_environment.c). We can reduce this
configuration to just adding static_hints to the kenv if we were previously
using them.
The changes in res_find are minimal and based on the observation that once
use_kenv gets set to '1' it will never be reset to '0', and it gets set to
'1' as soon as we hit fallback mode. Later work will refactor res_find a
little bit and eliminate this now-local, because it's become clear that
there's some funkiness revolving around use_kenv=1 and it being used to
imply that we're certainly looking at the dynamic_kenv.
Reviewed by: ray
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D15940
Using MMCCAM on AllWinner boards is now possible, reaching highest
possible data transfer speed.
For now, MMCCAM doesn't scan cards on boot. This means that scanning
has to be done manually and that it's not possible to mount root FS
from MMC/SD card since there is no block device at the boot time.
For manually scanning the cards, run:
# camcontrol rescan X:0:0
Where X is the bus number (look at camcontrol devlist to determine
bus number assigned to the MMC controller).
Reviewed by: manu
Approved by: imp (mentor)
Differential Revision: https://reviews.freebsd.org/D15891
The new stand/ structure installs loader.conf(5) and defaults/loader.conf
regardless of interpreter. The only thing gating installation now is
MK_BOOT.
Reported by: eadler
VERBOSE_SYSINIT is currently an all-or-nothing option. debug.verbose_sysinit
adds an option to have the code compiled in but quiet by default so that
getting this information from a device in the field doesn't necessarily
require distributing a recompiled kernel.
Its default is VERBOSE_SYSINIT's value as defined in the kernconf. As such,
the default behavior for simply omitting or including this option is
unchanged.
MFC after: 1 week
Many licenses on ar files contained small variations from the standard
FreeBSD license text. To avoid license proliferation switch to the usual
2-clause FreeBSD license after obtaining permission from all copyright
holders.
Approved by: jkoshy, kaiw, kientzle
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D14561
This works similar to WITH_SYSTEM_COMPILER added in r300354. It only
supports lld via WITH_LLD_BOOTSTRAP.
When both SYSTEM_COMPILER and SYSTEM_LINKER logic passes then libclang
will not build in cross-tools. If either check fails though then
libclang is built.
The .info is reworked to notify when libclang will be built since if
either clang or lld needs to be rebuilt, but not the other, the
notification can lead to confusion on why "clang is building".
-fuse-ld= is not used with this method so some combinations of compiler
and linker are expected to fail.
A new 'make test-system-linker' target is added to see the logic results.
Makefile.inc1:
CROSS_BINUTILS_PREFIX support had to be moved higher up so that XLD
could be set and MK_LLD_BOOTSTRAP disabled before checking SYSTEM_LINKER
logic as done with SYSTEM_COMPILER. This also required moving where
bsd.linker.mk was read since XLD needs to be set before parsing it. This
creates a situation where src.opts.mk can not test LINKER_FEATURES or
add LLD_BOOTSTAP to BROKEN_OPTIONS.
Reviewed by: emaste (earlier version)
Sponsored by: Dell EMC
Differential Revision: https://reviews.freebsd.org/D15894
lld always needs these DWARF sources, as well as other default and extra
tools. XDL seems to be the best fit list.
Remove MK_LLD_IS_LD check from SRCS_MIW which is now reduced to just a
few files for llvm-objdump.
Sponsored by: Dell EMC
Differential Revision: https://reviews.freebsd.org/D15915
MK_LLD is for the installed lld while MK_LLD_BOOTSTRAP is for the build
tool. For WITH_SYSTEM_LINKER it is necesarry to separate the logic of
these two. When building libllvm TOOLS_PREFIX will be defined and
MK_LLD_BOOTSTRAP should be checked instead.
Sponsored by: Dell EMC
Differential Revision: https://reviews.freebsd.org/D15837
LLD_BOOTSTRAP (build) is independent of LLD_IS_LD (installed) so they
should not be based on each other.
This is related to upcoming WITH_SYSTEM_LINKER work.
Reviewed by: emaste
Sponsored by: Dell EMC
Differential Revision: https://reviews.freebsd.org/D15836
This is needed for efifb.
arm and ricv pmap (the two arch with arm64 that uses subr_devmap) have very
different implementation so for now only add this for arm64.
Tested with efifb on Pine64 with a few other patches.
Reviewed by: cognet
Differential Revision: https://reviews.freebsd.org/D15294
The values for tx/rx delays differs accross the different DTS.
Mainline Linux set it to 0x24/0x18
Mostly-Vendor u-boot (the one maintained and developped) to 0x18/0x18
Mostly-Vendor linux (the one maintained and developped) to 0x26/0x11
By experience only 0x18/0x18 works so until the issue is resolved rely on
the bootloader settings.
The property are named {t,r}x_delay and not {t,r}-delay.
The upper bits of the register are a mask of which bits is allowed
to be written, set it otherwise we write nothing.
OF_getencprop returns <0 = for an error.
Pointy Hat: myself
Reported by: jmcneill (delay and mask bits)
Summary: In order to use cpufreq(4), a dev.cpu attachment must be created. If
the IBM property is found denoting SMT, attach only to the first thread setup,
so that a cpufreq device can bind.
Reviewed by: nwhitehorn
Differential Revision: https://reviews.freebsd.org/D15921
to FOREACH_PROC_IN_SYSTEM() to have a single pattern to look for.
Reviewed by: kib
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
Differential Revision: https://reviews.freebsd.org/D15916
Implement a ddb function walking the namecache to do this.
Reviewed by: jhb, mjg
Inspired by: gdb macro from jhb (old version)
Sponsored by: iXsystems, Inc.
Differential Revision: https://reviews.freebsd.org/D14898
fsid_t and ino_t are 64-bit entities, use uintmax_t typecast to ensure we
can print it on 32-bit or 64-bit architectures by using the %ju format for
prints.
Obtained from: Juniper Networks, Inc.
Observe:
printf "a\nb\nc\n" > /tmp/foo
# Next command results in no output
cat /tmp/foo | sort -m
# Next command results in proper output
cat /tmp/foo | sort -m -
# Also works:
sort -m /tmp/foo
Some const'ification was done to simplify the actual solution of adding "-"
explicitly to the file list if we didn't have any file arguments left over.
PR: 190099
MFC after: 1 week
