* All the supported firmwares have these flags set.
* This removes the following flags:
IWM_UCODE_TLV_FLAGS_PM_CMD_SUPPORT,
IWM_UCODE_TLV_FLAGS_NEWBT_COEX,
IWM_UCODE_TLV_FLAGS_BF_UPDATED,
IWM_UCODE_TLV_FLAGS_D3_CONTINUITY_API,
IWM_UCODE_TLV_FLAGS_STA_KEY_CMD,
IWM_UCODE_TLV_FLAGS_DEVICE_PS_CMD,
IWM_UCODE_TLV_FLAGS_SCHED_SCAN,
IWM_UCODE_TLV_FLAGS_RX_ENERGY_API,
IWM_UCODE_TLV_FLAGS_TIME_EVENT_API_V2
* Also remove definitions and code for dealing with the v1 time-event api.
* Remove unneeded calc_rssi() function.
Obtained from: dragonflybsd.git d078c812418d0e2c3392e99fa25fc776d07bdfad
Let firmware do its best first, and if it can't, try software recovery.
I would remove software timeout handler completely, but found bunch of
complains on command timeout on sparc64 mailing list few years ago, so
better be safe in case of interrupt loss.
MFC after: 2 weeks
mmc(4). For the most part, this consists of support for:
- Switching the signal voltage (VCCQ) to 1.8 V or (if supported
by the host controller) to 1.2 V,
- setting the UHS mode as appropriate in the SDHCI_HOST_CONTROL2
register,
- setting the power class in the eMMC device according to the
core supply voltage (VCC),
- using different bits for enabling a bus width of 4 and 8 bits
in the the eMMC device at DDR or higher timings respectively,
- arbitrating timings faster than high speed if there actually
are additional devices on the same MMC bus.
Given that support for DDR52 is not denoted by SDHCI capability
registers, availability of that timing is indicated by a new
quirk SDHCI_QUIRK_MMC_DDR52 and only enabled for Intel SDHCI
controllers so far. Generally, what it takes for a sdhci(4)
front-end to enable support for DDR52 is to hook up the bridge
method mmcbr_switch_vccq (which especially for 1.2 V signaling
support is chip/board specific) and the sdhci_set_uhs_timing
sdhci(4) method.
As a side-effect, this change also fixes communication with
some eMMC devices at SDR high speed mode with 52 MHz due to
the signaling voltage and UHS bits in the SDHCI controller no
longer being left in an inappropriate state.
Compared to 52 MHz at SDR high speed which typically yields
~45 MB/s with the eMMC chips tested, throughput goes up to
~80 MB/s at DDR52.
Additionally, this change already adds infrastructure and quite
some code for modes up to HS400ES and SDR104 respectively (I did
not want to add to much stuff at a time, though). Essentially,
what is still missing in order to be able to activate support
for these latter is is support for and handling of (re-)tuning.
o In sdhci(4), add two tunables hw.sdhci.quirk_clear as well as
hw.sdhci.quirk_set, which (when hooked up in the front-end)
allow to set/clear sdhci(4) quirks for debugging and testing
purposes. However, especially for SDHCI controllers on the
PCI bus which have no specific support code so far and, thus,
are picked up as generic SDHCI controllers, hw.sdhci.quirk_set
allows for setting the necessary quirks (if required).
o In mmc(4), check and handle the return values of some more
function calls instead of assuming that everything went right.
In case failures actually are not problematic, indicate that
by casting the return value to void.
Reviewed by: jmcneill
For 24xx and above use 2 vectors (default and response queue).
For 26xx and above use 3 vectors (default, response and ATIO queues).
Due to global lock interrupt hardlers never run simultaneously now, but
at least this allows to save one regitster read per interrupt.
MFC after: 2 weeks
Since we support RQSTYPE_RPT_ID_ACQ, that functionality is only useful
in loop mode, which probably doesn't worth having this hack in 2017.
MFC after: 2 weeks
When I initially did this 11n TX work in days of yonder, my 802.11 standards
clue was ... not as finely tuned. One of the things in 802.11-2012 (which
I guess technically was after I did this work, but I'm sure it was like this
in the previous rev?) is that among other traffic classes, three things are
important:
* group addressed frames should be default non-QoS, even if they're QoS frames, and
* group addressed frames should have a seqno out of a different space than the
per-TID QoS one; and because of this
* group addressed frames, being non-QoS, should never be in the Block-ACK window
for TX.
Now, net80211 and now this code cheats by using the non-QOS TID, but ideally
we'd introduce a separate seqno space just for multicast/group traffic for
TX and RX comparison.
Later extensions (eg reliable multicast / multimedia) express what one should do
when doing multicast traffic in a TID. Now, technically we /could/ do group traffic
as QoS traffic and throw it into a per-TID seqno space, but this definitely
introduces ordering issues when you take into account things like CABQ behaviour.
(Ie, if some traffic in the TID goes into the CABQ and some doesn't, because
it's doing a split of multicast and non-multicast traffic, then you have
seqno ordering issues.)
So, until someone implements 802.11vv reliable multicast / multimedia extensions,
group traffic is non-QoS.
Next, software/hardware queue TID mapping. In the past I believed the WME tagging
of frames because well, net80211 had a habit of tagging things like management
traffic with it. But, then we also map QoS traffic categories to TIDs as well.
So, we should obey the TID! But! then it put some management traffic into higher
WME categories too, as those frames don't have QoS TIDs. But! It'd do things like
put things like QoS action frames into higher WME categories, when they should
be kept in-order with the rest of the traffic for that TID. So! Given all of this,
the ath(4) driver does overrides to not trust the WME category.
I .. am undoing some of this. Now, the TID has a 1:1 mapping to the hardware
queue. The TID is the primary source of truth now for all QoS traffic.
The WME is only used for non-QoS traffic. This now means that any TID traffic
queued should be consistently queued regardless of WME, so things like the
"TX finished, do more TX" that is occuring right now for transmit handling
should be "better".
The consistent {TID, WME} -> hardware queue mapping is important for
transmit completion. It's used to schedule more traffic for that
particular TID, because that {many TID}:{1 TXQ} mapping in ath_tx_tid_sched()
is used for driving completion. Ie, when the hardware queue completes,
it'll walk that list of scheduled TIDs attached to that TXQ.
The eventual aim is to get ready for some other features around putting
some data into other hardware queues (eg for better PS-POLL support,
uAPSD, support, correct-er TDMA support, etc) which requires that
I tidy all of this up in preparation for then introducing further
TID scheduling that isn't linked to a hardware TXQ (likely a per-WME, per-TID
driver queue, and a per-node driver queue) to enable that.
Tested:
* AR9380, STA mode
* AR9380, AR9580, AP mode
There were two copies of the code: one in generic code was half-broken, and
another in platform code was never called. Leave only one in generic code
and working.
MFC after: 2 weeks
for vt. Restore syscons' rendering of background (bg) brightness as
foreground (fg) blinking and vice versa, and add rendering of blinking
as background brightness to vt.
Bright/saturated is conflated with light/white in the implementation
and in this description.
Bright colors were broken in all cases, but appeared to work in the
only case shown by "vidcontrol show". A boldness hack was applied
only in 1 layering-violation place (for some syscons sequences) where
it made some cases seem to work but was undone by clearing bold using
ANSI sequences, and more seriously was not undone when setting
ANSI/xterm dark colors so left them bright. Move this hack to drivers.
The boldness hack is only for fg brightness. Restore/add a similar hack
for bg brightness rendered as fg blinking and vice versa. This works
even better for vt, since vt changes the default text mode to give the
more useful bg brightness instead of fg blinking.
The brightness bit in colors was unnecessarily removed by the boldness
hack. In other cases, it was lost later by teken_256to8(). Use
teken_256to16() to not lose it. teken_256to8() was intended to be
used for bg colors to allow finer or bg-specific control for the more
difficult reduction to 8; however, since 16 bg colors actually work
on VGA except in syscons text mode and the conversion isn't subtle
enough to significantly in that mode, teken_256to8() is not used now.
There are still bugs, especially in vidcontrol, if bright/blinking
background colors are set.
Restore XOR logic for bold/bright fg in syscons (don't change OR
logic for vt). Remove broken ifdef on FG_UNDERLINE and its wrong
or missing bit and restore the correct hard-coded bit. FG_UNDERLINE
is only for mono mode which is not really supported.
Restore XOR logic for blinking/bright bg in syscons (in vt, add
OR logic and render as bright bg). Remove related broken ifdef
on BG_BLINKING and its missing bit and restore the correct
hard-coded bit. The same bit means blinking or bright bg depending
on the mode, and we want to ignore the difference everywhere.
Simplify conversions of attributes in syscons. Don't pretend to
support bold fonts. Don't support unusual encodings of brightness.
It is as good as possible to map 16 VGA colors to 16 xterm-16
colors. E.g., VGA brown -> xterm-16 Olive will be converted back
to VGA brown, so we don't need to convert to xterm-256 Brown. Teken
cons25 compatibility code already does the same, and duplicates some
small tables. This is mostly for the sc -> te direction. The other
direction uses teken_256to16() which is too generic.
nodes from the DTB by default. This will allow us to enumerate the CPUs
without hard coding the CPU count into code.
Reviewed by: br
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D9827
registers.
- Add slot type capability bits. These bits should allow recognizing
removable card slots, embedded cards and shared buses (shared bus
supposedly is always comprised of non-removable cards).
- Dump CAPABILITIES2, ADMA_ERR, HOST_CONTROL2 and ADMA_ADDRESS_LO
registers in sdhci_dumpregs().
- The drive type support flags in the CAPABILITIES2 register are for
drive types A,C,D, drive type B is the default setting (value 0) of
the drive strength field in the SDHCI_HOST_CONTROL2 register.
Obtained from: DragonFlyBSD (9e3c8f63, 455bd1b1)
the default partition, eMMC v4.41 and later devices can additionally
provide up to:
1 enhanced user data area partition
2 boot partitions
1 RPMB (Replay Protected Memory Block) partition
4 general purpose partitions (optionally with a enhanced or extended
attribute)
Of these "partitions", only the enhanced user data area one actually
slices the user data area partition and, thus, gets handled with the
help of geom_flashmap(4). The other types of partitions have address
space independent from the default partition and need to be switched
to via CMD6 (SWITCH), i. e. constitute a set of additional "disks".
The second kind of these "partitions" doesn't fit that well into the
design of mmc(4) and mmcsd(4). I've decided to let mmcsd(4) hook all
of these "partitions" up as disk(9)'s (except for the RPMB partition
as it didn't seem to make much sense to be able to put a file-system
there and may require authentication; therefore, RPMB partitions are
solely accessible via the newly added IOCTL interface currently; see
also below). This approach for one resulted in cleaner code. Second,
it retains the notion of mmcsd(4) children corresponding to a single
physical device each. With the addition of some layering violations,
it also would have been possible for mmc(4) to add separate mmcsd(4)
instances with one disk each for all of these "partitions", however.
Still, both mmc(4) and mmcsd(4) share some common code now e. g. for
issuing CMD6, which has been factored out into mmc_subr.c.
Besides simply subdividing eMMC devices, some Intel NUCs having UEFI
code in the boot partitions etc., another use case for the partition
support is the activation of pseudo-SLC mode, which manufacturers of
eMMC chips typically associate with the enhanced user data area and/
or the enhanced attribute of general purpose partitions.
CAVEAT EMPTOR: Partitioning eMMC devices is a one-time operation.
- Now that properly issuing CMD6 is crucial (so data isn't written to
the wrong partition for example), make a step into the direction of
correctly handling the timeout for these commands in the MMC layer.
Also, do a SEND_STATUS when CMD6 is invoked with an R1B response as
recommended by relevant specifications. However, quite some work is
left to be done in this regard; all other R1B-type commands done by
the MMC layer also should be followed by a SEND_STATUS (CMD13), the
erase timeout calculations/handling as documented in specifications
are entirely ignored so far, the MMC layer doesn't provide timeouts
applicable up to the bridge drivers and at least sdhci(4) currently
is hardcoding 1 s as timeout for all command types unconditionally.
Let alone already available return codes often not being checked in
the MMC layer ...
- Add an IOCTL interface to mmcsd(4); this is sufficiently compatible
with Linux so that the GNU mmc-utils can be ported to and used with
FreeBSD (note that due to the remaining deficiencies outlined above
SANITIZE operations issued by/with `mmc` currently most likely will
fail). These latter will be added to ports as sysutils/mmc-utils in
a bit. Among others, the `mmc` tool of the GNU mmc-utils allows for
partitioning eMMC devices (tested working).
- For devices following the eMMC specification v4.41 or later, year 0
is 2013 rather than 1997; so correct this for assembling the device
ID string properly.
- Let mmcsd.ko depend on mmc.ko. Additionally, bump MMC_VERSION as at
least for some of the above a matching pair is required.
- In the ACPI front-end of sdhci(4) describe the Intel eMMC and SDXC
controllers as such in order to match the PCI one.
Additionally, in the entry for the 80860F14 SDXC controller remove
the eMMC-only SDHCI_QUIRK_INTEL_POWER_UP_RESET.
OKed by: imp
Submitted by: ian (mmc_switch_status() implementation)
Fix this by using more dynamic initialization with simpler ifdefs for
the machine dependencies. Find a frame buffer address in a more
portable way that at least compiles on sparc64.
inpcb. t4_tom detaches the inpcb from the toepcb as soon as the
hardware is done with the connection (in final_cpl_received) but the
socket is around as long as the cm_id and the rest of iWARP state is.
This fixes an intermittent NULL dereference during abort.
Submitted by: KrishnamRaju ErapaRaju @ Chelsio
MFC after: 3 days
Sponsored by: Chelsio Communications
This patch fixes typo which results in extra bits of PMU control register.
PR: 217782
Submitted by: Svyatoslav <razmyslov at viva64.com>
Found by: PVS-Studio
Instead of single isp_intr() function doing all possible magic, introduce
four different functions to handle mailbox operation completions, async
events, response and ATIO queues. The goal is to isolate different code
paths to make code more readable, and to make easier support for multiple
interrupt vectors. Even oldest hardware in many cases can identify what
code path it should run on interrupt. Contemporary hardware can assign
them to different interrupt vectors.
MFC after: 2 weeks
inet_ntoa() and inet_ntoa_r() take the address in network
byte-order. When I removed those calls, I should have
replaced them with ntohl() to make the hex addresses slightly
less unreadable. Here they are.
See r315277 regarding classic blunders.
vangyzen: you're deep in "no good deed" territory, it seems
--badger
Reported by: ian
MFC after: 3 days
MFC when: I finally get it right
Sponsored by: Dell EMC
