An old route will be NULL at that point if a packet were initially
routed to an interface (using the IP_ROUTETOIF flag.)
Submitted by: Igor Timkin <ivt@gamma.ru>
All TCP ISNs that are sent out are valid cookies, which allows entries
in the syncache to be dropped and still have the ACK accepted later.
As all entries pass through the syncache, there is no sudden switchover
from cache -> cookies when the cache is full; instead, syncache entries
simply have a reduced lifetime. More details may be found in the
"Resisting DoS attacks with a SYN cache" paper in the Usenix BSDCon 2002
conference proceedings.
Sponsored by: DARPA, NAI Labs
the shutdown request at reboot/halt time.
Disable the printf 'vnlru process getting nowhere, pausing...' and instead
export the count to the debug.vnlru_nowhere sysctl.
of polling interfaces at the lowest possible priority
(this might result in softnetisr being scheduled, but there is
no risk of livelock because they have a higher priority than
this thread).
otherwise breaks on the Alpha arch. I think this is wrong since i'd
actually like to probe for a PC architecture, not for a particular CPU
type. Anyway, now it's again the way it used to be.
*) Sync with 4.4BSD-Lite2
*) Set usecs for utimes()
*) Add 'inc' command and 'autoinc' option that check for new mail
manually and automatically, respectively
*) Use POSIX signal handling and tty semantics
*) Handle long lines correctly when paging messages
*) Add ability to explicitly search 'To:' line
*) Various manpage cleanups
*) Support overriding '~/.mailrc' with $MAILRC
*) Support 'askbcc' and 'asksub' options
*) Fix various bugs
Reviewed by: ru (mail.1)
Obtained from: NetBSD
by me to make it more efficient. The original code had serious balancing
problems and could also deadlock easily. This code relegates the vnode
reclamation to its own kproc and relaxes the vnode reclamation requirements
to better maintain kern.maxvnodes. This code still doesn't balance as well
as it could, but it does a much better job then the original code.
Approved by: re@freebsd.org
Obtained from: ps, peter, dillon
MFS Assuming: Assuming no problems crop up in Yahoo testing
MFC after: 7 days
remove the check from addupc_task(). It would need sched_lock while
testing the flag anyways.
- Always read sticks while holding sched_lock using a temporary variable
where needed.
- Always init prticks to 0 in ast() to quiet a warning.
sense, and mode select into their 10 byte equivalents. Eventually the
da(4) driver will become more intelligent about this, or at least allow
umass(4) to pass quirks in directly. However, this is a functional
workaround until a better fix is implemented.
- Use the 6 to 10 conversion function to allow the ATAPI and UFI command
sets to emulate 6 byte commands with 10 byte commands.
- Use the ATAPI command set rather than UFI for the ScanLogic SL11R-IDE
as it supports the SYNCH_CACHE command.
- Enable ATAPI command set support.
- Pass READ/WRITE_12 commands through for UFI support as the UFI spec
says they should be supported.
- Update a comment in the UFI translation function since we handle
MODE_SELECT.
temporary storage. In the old NFS code it wasn't at all clear if
the value of `tl' was used across or after macro calls, but I'm
fairly confident that the convention was to keep its use local.
Each ex-macro function now uses a local version of this variable,
so all of the double-indirection goes away.
The only exception to the `local use' rule for `tl' is nfsm_clget(),
which is left unchanged by this commit.
Reviewed by: peter
- The MD functions critical_enter/exit are renamed to start with a cpu_
prefix.
- MI wrapper functions critical_enter/exit maintain a per-thread nesting
count and a per-thread critical section saved state set when entering
a critical section while at nesting level 0 and restored when exiting
to nesting level 0. This moves the saved state out of spin mutexes so
that interlocking spin mutexes works properly.
- Most low-level MD code that used critical_enter/exit now use
cpu_critical_enter/exit. MI code such as device drivers and spin
mutexes use the MI wrappers. Note that since the MI wrappers store
the state in the current thread, they do not have any return values or
arguments.
- mtx_intr_enable() is replaced with a constant CRITICAL_FORK which is
assigned to curthread->td_savecrit during fork_exit().
Tested on: i386, alpha
