NFS client (which I guess is no longer experimental). The fstype "newnfs"
is now "nfs" and the regular/old NFS client is now fstype "oldnfs".
Although mounts via fstype "nfs" will usually work without userland
changes, an updated mount_nfs(8) binary is needed for kernels built with
"options NFSCL" but not "options NFSCLIENT". Updated mount_nfs(8) and
mount(8) binaries are needed to do mounts for fstype "oldnfs".
The GENERIC kernel configs have been changed to use options
NFSCL and NFSD (the new client and server) instead of NFSCLIENT and NFSSERVER.
For kernels being used on diskless NFS root systems, "options NFSCL"
must be in the kernel config.
Discussed on freebsd-fs@.
device in /dev/ create symbolic link with adY name, trying to mimic old ATA
numbering. Imitation is not complete, but should be enough in most cases to
mount file systems without touching /etc/fstab.
- To know what behavior to mimic, restore ATA_STATIC_ID option in cases
where it was present before.
- Add some more details to UPDATING.
stack. It means that all legacy ATA drivers are disabled and replaced by
respective CAM drivers. If you are using ATA device names in /etc/fstab or
other places, make sure to update them respectively (adX -> adaY,
acdX -> cdY, afdX -> daY, astX -> saY, where 'Y's are the sequential
numbers for each type in order of detection, unless configured otherwise
with tunables, see cam(4)).
ataraid(4) functionality is now supported by the RAID GEOM class.
To use it you can load geom_raid kernel module and use graid(8) tool
for management. Instead of /dev/arX device names, use /dev/raid/rX.
MPERF MSRs are available. It was disabled in r216443. Remove the earlier
hack to subtract 0.5% from the calibrated frequency as DELAY(9) is little
bit more reliable now.
safer for i386 because it can be easily over 4 GHz now. More worse, it can
be easily changed by user with 'machdep.tsc_freq' tunable (directly) or
cpufreq(4) (indirectly). Note it is intentionally not used in performance
critical paths to avoid performance regression (but we should, in theory).
Alternatively, we may add "virtual TSC" with lower frequency if maximum
frequency overflows 32 bits (and ignore possible incoherency as we do now).
functions are implemented with CMPXCHG8B instruction where it is available,
i. e., all Pentium-class and later processors. Note this instruction is
also used for atomic_store_rel_64() because a simple XCHG-like instruction
for 64-bit memory access does not exist, unfortunately. If the processor
lacks the instruction, i. e., 80486-class CPUs, two 32-bit load/store are
performed with interrupt temporarily disabled, assuming it does not support
SMP. Although this assumption may be little naive, it is true in reality.
This implementation is inspired by Linux.
Introduce the AHB glue for Atheros embedded systems. Right now it's
hard-coded for the AR9130 chip whose support isn't yet in this HAL;
it'll be added in a subsequent commit.
Kernel configuration files now need both 'ath' and 'ath_pci' devices; both
modules need to be loaded for the ath device to work.
- entirely eliminate some calls to uio_yeild() as being unnecessary,
such as in a sysctl handler.
- move should_yield() and maybe_yield() to kern_synch.c and move the
prototypes from sys/uio.h to sys/proc.h
- add a slightly more generic kern_yield() that can replace the
functionality of uio_yield().
- replace source uses of uio_yield() with the functional equivalent,
or in some cases do not change the thread priority when switching.
- fix a logic inversion bug in vlrureclaim(), pointed out by bde@.
- instead of using the per-cpu last switched ticks, use a per thread
variable for should_yield(). With PREEMPTION, the only reasonable
use of this is to determine if a lock has been held a long time and
relinquish it. Without PREEMPTION, this is essentially the same as
the per-cpu variable.
Clear the padding when returning context to the usermode, for
MI ucontext_t and x86 MD parts.
Kernel allocates the structures on the stack, and not clearing
reserved fields and paddings causes leakage.
the original amd64 and i386 headers with stubs.
Rename (AMD64|I386)_BUS_SPACE_* to X86_BUS_SPACE_* everywhere.
Reviewed by: imp (previous version), jhb
Approved by: kib (mentor)
Passing a count of zero on i386 and amd64 for [I386|AMD64]_BUS_SPACE_MEM
causes a crash/hang since the 'loop' instruction decrements the counter
before checking if it's zero.
PR: kern/80980
Discussed with: jhb
functions, they are unused. Remove 'user' from npxgetuserregs()
etc. names.
For {npx,fpu}{get,set}regs(), always use pcb->pcb_user_save for FPU
context storage. This eliminates the need for ugly copying with
overwrite of the newly added and reserved fields in ucontext on i386
to satisfy alignment requirements for fpusave() and fpurstor().
pc98 version was copied from i386.
Suggested and reviewed by: bde
Tested by: pho (i386 and amd64)
MFC after: 1 week
contents of the ones that were not empty were stale and unused.
- Now that <machine/mutex.h> no longer exists, there is no need to allow it
to override various helper macros in <sys/mutex.h>.
- Rename various helper macros for low-level operations on mutexes to live
in the _mtx_* or __mtx_* namespaces. While here, change the names to more
closely match the real API functions they are backing.
- Drop support for including <sys/mutex.h> in assembly source files.
Suggested by: bde (1, 2)
work properly with single-stepping in a kernel debugger. Specifically,
these routines have always disabled interrupts before increasing the nesting
count and restored the prior state of interrupts after decreasing the nesting
count to avoid problems with a nested interrupt not disabling interrupts
when acquiring a spin lock. However, trap interrupts for single-stepping
can still occur even when interrupts are disabled. Now the saved state of
interrupts is not saved in the thread until after interrupts have been
disabled and the nesting count has been increased. Similarly, the saved
state from the thread cannot be read once the nesting count has been
decreased to zero. To fix this, use temporary variables to store interrupt
state and shuffle it between the thread's MD area and the appropriate
registers.
In cooperation with: bde
MFC after: 1 month
The main goal of this is to generate timer interrupts only when there is
some work to do. When CPU is busy interrupts are generating at full rate
of hz + stathz to fullfill scheduler and timekeeping requirements. But
when CPU is idle, only minimum set of interrupts (down to 8 interrupts per
second per CPU now), needed to handle scheduled callouts is executed.
This allows significantly increase idle CPU sleep time, increasing effect
of static power-saving technologies. Also it should reduce host CPU load
on virtualized systems, when guest system is idle.
There is set of tunables, also available as writable sysctls, allowing to
control wanted event timer subsystem behavior:
kern.eventtimer.timer - allows to choose event timer hardware to use.
On x86 there is up to 4 different kinds of timers. Depending on whether
chosen timer is per-CPU, behavior of other options slightly differs.
kern.eventtimer.periodic - allows to choose periodic and one-shot
operation mode. In periodic mode, current timer hardware taken as the only
source of time for time events. This mode is quite alike to previous kernel
behavior. One-shot mode instead uses currently selected time counter
hardware to schedule all needed events one by one and program timer to
generate interrupt exactly in specified time. Default value depends of
chosen timer capabilities, but one-shot mode is preferred, until other is
forced by user or hardware.
kern.eventtimer.singlemul - in periodic mode specifies how much times
higher timer frequency should be, to not strictly alias hardclock() and
statclock() events. Default values are 2 and 4, but could be reduced to 1
if extra interrupts are unwanted.
kern.eventtimer.idletick - makes each CPU to receive every timer interrupt
independently of whether they busy or not. By default this options is
disabled. If chosen timer is per-CPU and runs in periodic mode, this option
has no effect - all interrupts are generating.
As soon as this patch modifies cpu_idle() on some platforms, I have also
refactored one on x86. Now it makes use of MONITOR/MWAIT instrunctions
(if supported) under high sleep/wakeup rate, as fast alternative to other
methods. It allows SMP scheduler to wake up sleeping CPUs much faster
without using IPI, significantly increasing performance on some highly
task-switching loads.
Tested by: many (on i386, amd64, sparc64 and powerc)
H/W donated by: Gheorghe Ardelean
Sponsored by: iXsystems, Inc.
This reflects actual type used to store and compare child device orders.
Change is mostly done via a Coccinelle (soon to be devel/coccinelle)
semantic patch.
Verified by LINT+modules kernel builds.
Followup to: r212213
MFC after: 10 days
zones for each malloc bucket size. The purpose is to isolate
different malloc types into hash classes, so that any buffer overruns
or use-after-free will usually only affect memory from malloc types in
that hash class. This is purely a debugging tool; by varying the hash
function and tracking which hash class was corrupted, the intersection
of the hash classes from each instance will point to a single malloc
type that is being misused. At this point inspection or memguard(9)
can be used to catch the offending code.
Add MALLOC_DEBUG_MAXZONES=8 to -current GENERIC configuration files.
The suggestion to have this on by default came from Kostik Belousov on
-arch.
This code is based on work by Ron Steinke at Isilon Systems.
Reviewed by: -arch (mostly silence)
Reviewed by: zml
Approved by: zml (mentor)
get_fpcontext(), and npxsetuserregs() for set_fpcontext). Also,
note that usercontext is not initialized anymore in fpstate_drop().
Systematically replace references to npxgetregs() and npxsetregs()
by npxgetuserregs() and npxsetuserregs() in comments.
Noted by: bde
removal, MFi386 r209198:
Use critical sections instead of disabling local interrupts to ensure
the consistency between PCPU fpcurthread and the state of FPU.
Reviewed by: bde
Tested by: pho
believed that all 486-class CPUs FreeBSD is capable to run on, either
have no FPU and cannot use external coprocessor, or have FPU on the
package and can use #MF.
Reviewed by: bde
Tested by: pho (previous version)
writing event timer drivers, for choosing best possible drivers by machine
independent code and for operating them to supply kernel with hardclock(),
statclock() and profclock() events in unified fashion on various hardware.
Infrastructure provides support for both per-CPU (independent for every CPU
core) and global timers in periodic and one-shot modes. MI management code
at this moment uses only periodic mode, but one-shot mode use planned for
later, as part of tickless kernel project.
For this moment infrastructure used on i386 and amd64 architectures. Other
archs are welcome to follow, while their current operation should not be
affected.
This patch updates existing drivers (i8254, RTC and LAPIC) for the new
order, and adds event timers support into the HPET driver. These drivers
have different capabilities:
LAPIC - per-CPU timer, supports periodic and one-shot operation, may
freeze in C3 state, calibrated on first use, so may be not exactly precise.
HPET - depending on hardware can work as per-CPU or global, supports
periodic and one-shot operation, usually provides several event timers.
i8254 - global, limited to periodic mode, because same hardware used also
as time counter.
RTC - global, supports only periodic mode, set of frequencies in Hz
limited by powers of 2.
Depending on hardware capabilities, drivers preferred in following orders,
either LAPIC, HPETs, i8254, RTC or HPETs, LAPIC, i8254, RTC.
User may explicitly specify wanted timers via loader tunables or sysctls:
kern.eventtimer.timer1 and kern.eventtimer.timer2.
If requested driver is unavailable or unoperational, system will try to
replace it. If no more timers available or "NONE" specified for second,
system will operate using only one timer, multiplying it's frequency by few
times and uing respective dividers to honor hz, stathz and profhz values,
set during initial setup.
FPU/SSE hardware. Caller should provide a save area that is chained
into the stack of the areas; pcb save_area for usermode FPU state is
on top. The pcb now contains a pointer to the current FPU saved area,
used during FPUDNA handling and context switches. There is also a
facility to allow the kernel thread to use pcb save_area.
Change the dreaded warnings "npxdna in kernel mode!" into the panics
when FPU usage is not registered.
KPI discussed with: fabient
Tested by: pho, fabient
Hardware provided by: Sentex Communications
MFC after: 1 month
