This allows the PF interfaces to communicate with the VF interfaces over
the internal switch in the ASIC. Fix the GL limits for VM work requests
while here.
MFC after: 3 days
Sponsored by: Chelsio Communications
vm_ooffset_t is now unsigned. Remove some tests for negative values,
or make other adjustments accordingly.
Reported by: Coverity
Reviewed by: kib markj
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D26214
Hardware assistance includes checksumming (tx and rx), TSO, and RSS on
the inner traffic in a VXLAN tunnel.
Relnotes: Yes
Sponsored by: Chelsio Communications
From Franco:
The iflib rewrite forced the promisc flag but it was not reported
to the system. Noticed on a stock VM that went into unsolicited
promisc mode when dhclient was started during bootup.
PR: 248869
Submitted by: Franco Fichtner <franco@opnsense.org>
Reviewed by: erj@
MFC after: 3 days
This re-adds the opt_rss.h header to the driver and includes some
RSS-specific headers when RSS is defined.
PR: 249191
Submitted by: Milosz Kaniewski <milosz.kaniewski@gmail.com>
MFC after: 3 days
We don't need to do the busy dance for this driver. It's handled by
destroy_dev() entirely. Since all we did was busy/unbusy in
open/close, just delete them. We therefore don't need to track closes
either.
Reviewed by: ian@
Differential Revision: https://reviews.freebsd.org/D26431
vendor ID string to say just "Microchip Technology" -- the buyout of
Standard Microsystems happened in 2012 and the SMC/SMSC names are pretty
much retired at this point.
PR: 241406
Add enough infrastructure for interrupts on children of the pl061 GPIO
controller. As gpiobus already provided these the pl061 driver also needs
to pass requests up the newbus hierarchy.
Currently there are no children that expect to configure interrupts, however
this is expected to change to support the ACPI Event Information interface.
Sponsored by: Innovate UK
that can be extended, but also ensure compile-time type checking. Refactor
common code out of arch-specific implementations. Move the mpr and mps
drivers to this new API. The template type remains visible to the consumer
so that it can be allocated on the stack, but should be considered opaque.
This update adds support for:
HW VLAN tagging
HW checksum offload for IPv4 and IPv6
tx and rx aggreegation (for full gige speeds)
multiple transactions
In my testing, I am able to get 900-950Mbps depending upon
TCP or UDP, which is a significant improvement over the previous
91Mbps (~8kint/sec*1500bytes/packet*1packet/int).
Reviewed by: hselasky
MFC after: 2 months
Differential Revision: https://reviews.freebsd.org/D25809
In r365419 ieee80211_media_change() callers were updated to not longer
act on the obselete ENETRESET return code.
While in the old days iwm has done a stop/init cycle in these cases,
this was not executed since r193340.
As a consequence simplify iwm code as well by passing ieee80211_media_change()
right to ieee80211_vap_attach() as there is no more need for a local
implementation.
Reported by: Tomoaki AOKI (junchoon dec.sakura.ne.jp)
Tested by: Tomoaki AOKI (junchoon dec.sakura.ne.jp)
MFC after: 3 days
X-MFC: fix is already in stable/12
PR: 248955
Summary of changes:
- Assorted bug fixes
- Support for newer versions of the device firmware
- Suspend/resume support
- Support for Lenient Link Mode for E82X devices (e.g. can try to link with
SFP/QSFP modules with bad EEPROMs)
- Adds port-level rx_discards sysctl, similar to ixl(4)'s
This version of the driver is intended to be used with DDP package 1.3.16.0,
which has already been updated in a previous commit.
Tested by: Jeffrey Pieper <jeffrey.e.pieper@intel.com>
MFC after: 3 days
MFC with: r365332, r365550
Sponsored by: Intel Corporation
Differential Revision: https://reviews.freebsd.org/D26322
As the pl061 driver can be an interrupt controller attach it earlier in the
boot so other drivers can use it.
Use a new GPIO xref to not conflict with the existing root interrupt
controller.
Sponsored by: Innovate UK
It could be used in various IOMMU platforms, not only DMAR.
Reviewed by: kib
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D26373
On arm64 we may boot via ACPI. In this case we will still try to manage the
gpio providers as if we are using FDT. Fix this by checking if the FDT node
is valid before registering a cross reference.
Sponsored by: Innovate UK
Future changes would require additional initialization of OBJT_PHYS
objects, and vm_object_allocate() is not suitable for it.
Reviewed by: markj
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D24652
The cryptodev_process() method should either return 0 if it has
completed a request, or ERESTART to defer the request until later. If
a request encounters an error, the error should be reported via
crp_etype before completing the request via crypto_done().
Fix a few more drivers noticed by asomers@ similar to the fix in
r365389. This is an old bug, but went unnoticed since crypto requests
did not start failing as a normal part of operation until digest
verification was introduced which can fail requests with EBADMSG.
PR: 247986
Reported by: asomers
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D26361
RISC-V is currently built with -Wno-format, which is how these went
undetected. Address them now before re-enabling those warnings.
Differential Revision: https://reviews.freebsd.org/D26319
A PL061 is a simple 8 pin GPIO controller. This GPIO device is used to
signal an internal request for shutdown on some virtual machines including
Arm-based Amazon EC2 instances.
Submitted by: Ali Saidi <alisaidi_amazon.com> (previouss version)
Reviewed by: Ali Saidi, manu
Differential Revision: https://reviews.freebsd.org/D24065
In r178354 with the introduction of multi-bss ("vap") support factoring
out started and with r193340 ieee80211_media_change() no longer returned
ENETRESET but only 0 or error.
As ieee80211(9) tells the ieee80211_media_change() function should not
be called directly but is registered with ieee80211_vap_attach() instead.
Some drivers have not been fully converted. After fixing the return
checking some of these functions were simply wrappers between
ieee80211_vap_attach() and ieee80211_media_change(), so remove the extra
function, where possible as well.
PR: 248955
Submitted by: Tong Zhang (ztong0001 gmail.com) (original)
MFC after: 3 days
Sponsored by: The FreeBSD Foundation
At least on Orange Pi PC Plus even the host mode does not work without
enabling the phy and setting it to the host mode.
The driver will now parse dr_mode property and will try to configure
itself and the phy accordingly.
OTG mode is not supported yet, so it is treated as the device / peripheral
mode.
The phy is enabled -- powered on -- only for the host mode.
The device mode requires support from a phy driver, e.g., aw_usbphy on
Allwinner platform.
aw_usbphy does not support the device mode, so it cannnot work yet.
MFC after: 6 weeks
Otherwise, I get this panic:
panic: awusbdrd_reg: Invalid register 0x342
It looks that musb code both writes and reads at least MUSB2_REG_TXDBDIS.
MFC after: 5 weeks
X-MFC after: r365399
Make that distinction more explicit and regular in the code.
The difference in behavior is documented in the respective datasheets.
Previously, the code handled the distinction by writing the control
register multiple times where at least one write was zero and another
was one.
This can be considered a follow-up to r363021.
Reviewed by: manu
MFC after: 4 weeks
Differential Revision: https://reviews.freebsd.org/D26308
wakeup() does not have any effect on pause(), so if a transfer was
not finished by the time of the first check, then the thread
would sleep full 30 ms.
To do: protect the transfer and interrupt code with the mutex,
switch from tsleep from msleep
Reviewed by: manu
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D26309
abs() takes a (signed) int as input.
Instead, it was used with unsigned 64-bit integers.
So, add and use a new helper function to calculate a difference between
two uint64_t-s.
Reviewed by: manu
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D26307
Investigating a hang I found having some more error information
available would be helpful, so be more verbose and also tell cam/xpt
status in case of error/panic.
Reviewed by: hselasky
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D26287
While debugging a hang I noticed that in case of error in
umass_cam_attach_sim() we miss a cam_sim_free() call.
Added that to not leak resources.
Reviewed by: hselasky
MFC after: 3 days
Differential Revision: D26287
Fix the build after r365264, I forgot to exclude arm in one more place.
Reported by: rpokala
Approved by: manu (implicit, build fix)
MFC after: 3 days
X-MFC-With: 365264
Pointy-hat to: zeising
mgb had a longstanding typo in function-like macro MGB_NEXT_RING_IDX's
argument, but the macro had no consumers. r365061 introduced a use of
the macro, after which mgb failed to build.
MFC after: 3 days
Sponsored by: The FreeBSD Foundation
hints data. Control register 2 holds the settings a user might want to
configure, such as the timeout value for idle busses and whether to enable
the mass-writes feature.
Also add hint support for disconnecting idle busses (which was already
supported using FDT data).
Update the manpage with the new features, and also split the hints section
into separate lists of required and optional hints.
