when polled mode is enabled. This should help with duplicated/missing
characters problem at mountroot, geli, etc. prompts on multi CPU systems
while kbdmux(4) is enabled.
Tested by: Tobias Grosser <grosser -at- fim -dot- uni-passau -dot- de>
Tested by: Fabian Keil <freebsd-listen -at- fabiankeil -dot- de>
MFC after: 3 days
network load.
1. Leave the RX interrupt routine if there is no mbuf available.
2. Properly initialize and track tx_desc_used_count counter so as not to
leak mbuf while traversing used descriptors.
Obtained from: Semihalf
- Remove redundant softc members for RIDs.
- Change some softc members to be unsigned where more appropriate.
- Add some missing const.
- Remove support for mmap(2)'ing VGA I/O as it was broken [1] and
not required by X.Org anyway.
- Fix some confusion between bus, physical and virtual addresses
which mostly consisted in using members of struct video_adapter
inappropriately but wasn't fatal except for the regular framebuffer
mmap(2)'ing.
- Remove redundant bzero(9)'ing of the softc.
- Don't map the framebuffer twice in case the firmware has already
mapped it as besides wasting resources this isn't possible with
all MMUs. This is a bit tricky as a) just because the firmware
provides a property with a virtual address doesn't mean it's
actually mapped (but typically is when the framebuffer is the
console) and b) the firmware doesn't necessarily map the it with
the same byteorder as we do. This make machfb(4) work on machines
with cheetah-class MMUs (including X.Org).
Reported by: Michael Plass [1]
MFC after: 3 days
addresses to BARs into new pci_read_bar() and pci_write_bar() routines.
pci_add_map(), pci_alloc_map(), and pci_delete_resource() now use these
routines to work with BARs.
- Just pass the device_t for the new PCI device to various routines instead
of passing the device, bus, slot, and function.
Reviewed by: imp
Remote host can advertise smaller MSS than that of sender so upper
stack might have adjusted the MSS which in turn generates IP
packets that are less size than that of interface MTU.
Reported by: Bjoern Koenig ( bkoenig <> alpha-tierchen dot de )
Tested by: Bjoern Koenig ( bkoenig <> alpha-tierchen dot de )
MFC after: 3 days
TCPSTAT_INC(), rather than directly manipulating the fields across the
kernel. This will make it easier to change the implementation of
these statistics, such as using per-CPU versions of the data structures.
MFC after: 3 days
1) Flag it and only access that command on the 3c1
2) The TX PLL appears to power down when not in use, so we have to power
it back up when we've been idle. Do this at the start of ifstart.
Otherwise we fall off the net.
have other media to test against, I've left that media reporting
unchanged.
o Enable the TX_PLL when we enable TX. This is harmless on most
cards, but required to get the 3c1 CF card working. Power savings
could be had by managing this better, but for now it gets my card
working.
We typically wire translation to devices with TLB1 entries and
pmap_kextract() does not know about those and returns 0. This
causes false positives (read: all serial ports suddenly become
the console).
Do not use Giant for kbdmux(4) locking. This is wrong and apparently
causing more problems than it solves. This will re-open the issue
where interrupt handlers may race with kbdmux(4) in polling mode.
Typical symptoms include (but not limited to) duplicated and/or
missing characters when low level console functions (such as gets)
are used while interrupts are enabled (for example geli password
prompt, mountroot prompt etc.)
MFC after: 3 days
