mapping size (currently unused). The flags includes the fault access
bits, wired flag as PMAP_ENTER_WIRED, and a new flag
PMAP_ENTER_NOSLEEP to indicate that pmap should not sleep.
For powerpc aim both 32 and 64 bit, fix implementation to ensure that
the requested mapping is created when PMAP_ENTER_NOSLEEP is not
specified, in particular, wait for the available memory required to
proceed.
In collaboration with: alc
Tested by: nwhitehorn (ppc aim32 and booke)
Sponsored by: The FreeBSD Foundation and EMC / Isilon Storage Division
MFC after: 2 weeks
The MD allocators were very common, however there were some minor
differencies. These differencies were all consolidated in the MI allocator,
under ifdefs. The defines from machine/vmparam.h turn on features required
for a particular machine. For details look in the comment in sys/sf_buf.h.
As result no MD code left in sys/*/*/vm_machdep.c. Some arches still have
machine/sf_buf.h, which is usually quite small.
Tested by: glebius (i386), tuexen (arm32), kevlo (arm32)
Reviewed by: kib
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
We continue to use pmap_enter() for that. For unwiring virtual pages, we
now use pmap_unwire(), which unwires a range of virtual addresses instead
of a single virtual page.
Sponsored by: EMC / Isilon Storage Division
be able to claim I know how the UART code works."
* Just return 115200 as the current baud rate. I should cache it in the
device struct and return that but I'm lazy right now.
* don't error out on other ioctl settings for now, just silently ignore them.
* remove some code that was copied from the 8250 driver that isn't needed
any longer.
Tested:
* AR9331, Carambola-2 board.
This commit does not add error returns to minidumpsys() or
textdump_dumpsys(); those can also be added later.
Submitted by: Conrad Meyer (EMC / Isilon storage division)
the upstream implementation and helps ensure that a trap induced by tracing
fbt::trap:entry is handled without recursively generating another trap.
This makes it possible to run most (but not all) of the DTrace tests under
common/safety/ without triggering a kernel panic.
Submitted by: Anton Rang <anton.rang@isilon.com> (original version)
Phabric: D95
several reasons for this change:
pmap_change_wiring() has never (in my memory) been used to set the wired
attribute on a virtual page. We have always used pmap_enter() to do that.
Moreover, it is not really safe to use pmap_change_wiring() to set the wired
attribute on a virtual page. The description of pmap_change_wiring() says
that it assumes the existence of a mapping in the pmap. However, non-wired
mappings may be reclaimed by the pmap at any time. (See pmap_collect().)
Many implementations of pmap_change_wiring() will crash if the mapping does
not exist.
pmap_unwire() accepts a range of virtual addresses, whereas
pmap_change_wiring() acts upon a single virtual page. Since we are
typically unwiring a range of virtual addresses, pmap_unwire() will be more
efficient. Moreover, pmap_unwire() allows us to unwire superpage mappings.
Previously, we were forced to demote the superpage mapping, because
pmap_change_wiring() only allowed us to express the unwiring of a single
base page mapping at a time. This added to the overhead of unwiring for
large ranges of addresses, including the implicit unwiring that occurs at
process termination.
Implementations for arm and powerpc will follow.
Discussed with: jeff, marcel
Reviewed by: kib
Sponsored by: EMC / Isilon Storage Division
handle packets up to 1536 bytes)
This fixes the need to frag that could happen when using vlans on top of
if_arge (which is a common case for the use the switch ports as individual
NICs).
Previously to this commit any vlan setup with if_arge as parent would have
the MTU of the parent interface reduced by the size of dot1q header
(4 bytes).
Tested on TP-Link 1043ND (where the WAN port is just a switch port setup to
tag packets in a different VLAN than the LAN ports).
Reported and tested by: Harm Weites (harm at weites.com)
These changes prevent sysctl(8) from returning proper output,
such as:
1) no output from sysctl(8)
2) erroneously returning ENOMEM with tools like truss(1)
or uname(1)
truss: can not get etype: Cannot allocate memory
there is an environment variable which shall initialize the SYSCTL
during early boot. This works for all SYSCTL types both statically and
dynamically created ones, except for the SYSCTL NODE type and SYSCTLs
which belong to VNETs. A new flag, CTLFLAG_NOFETCH, has been added to
be used in the case a tunable sysctl has a custom initialisation
function allowing the sysctl to still be marked as a tunable. The
kernel SYSCTL API is mostly the same, with a few exceptions for some
special operations like iterating childrens of a static/extern SYSCTL
node. This operation should probably be made into a factored out
common macro, hence some device drivers use this. The reason for
changing the SYSCTL API was the need for a SYSCTL parent OID pointer
and not only the SYSCTL parent OID list pointer in order to quickly
generate the sysctl path. The motivation behind this patch is to avoid
parameter loading cludges inside the OFED driver subsystem. Instead of
adding special code to the OFED driver subsystem to post-load tunables
into dynamically created sysctls, we generalize this in the kernel.
Other changes:
- Corrected a possibly incorrect sysctl name from "hw.cbb.intr_mask"
to "hw.pcic.intr_mask".
- Removed redundant TUNABLE statements throughout the kernel.
- Some minor code rewrites in connection to removing not needed
TUNABLE statements.
- Added a missing SYSCTL_DECL().
- Wrapped two very long lines.
- Avoid malloc()/free() inside sysctl string handling, in case it is
called to initialize a sysctl from a tunable, hence malloc()/free() is
not ready when sysctls from the sysctl dataset are registered.
- Bumped FreeBSD version to indicate SYSCTL API change.
MFC after: 2 weeks
Sponsored by: Mellanox Technologies
configs. Switch the BERI_NETFPGA_MDROOT to 64bit by default.
Give we have working interrupts also cleanup the extra polling CFLAGS from
the module Makefile.
MFC after: 2 weeks
the queue where to enqueue pages that are going to be unwired.
- Add stronger checks to the enqueue/dequeue for the pagequeues when
adding and removing pages to them.
Of course, for unmanaged pages the queue parameter of vm_page_unwire() will
be ignored, just as the active parameter today.
This makes adding new pagequeues quicker.
This change effectively modifies the KPI. __FreeBSD_version will be,
however, bumped just when the full cache of free pages will be
evicted.
Sponsored by: EMC / Isilon storage division
Reviewed by: alc
Tested by: pho
In particular, don't check the value of the bus_dma map against NULL
to determine if either bus_dmamem_alloc() or bus_dmamap_load() succeeded.
Instead, assume that bus_dmamap_load() succeeeded (and thus that
bus_dmamap_unload() should be called) if the bus address for a resource
is non-zero, and assume that bus_dmamem_alloc() succeeded (and thus
that bus_dmamem_free() should be called) if the virtual address for a
resource is not NULL.
In many cases these bugs could result in leaks when a driver was detached.
Reviewed by: yongari
MFC after: 2 weeks
- Update FDT file for BERI DE4 boards.
- Add needed kernel configuration keywords.
- Rename module to saf1761otg so that the device unit number does not
interfere with the hardware ID in dmesg.
Sponsored by: DARPA, AFRL
the GPIO pin is connected to a push button (or other devices).
Instead keep the boot loader settings.
Calling ar71xx_gpio_pin_configure() with DEFAULT_CAPS was probably a
mistake and was causing all the pins to be set as outputs.
at that time, but AFAIK it is only used on routerboards.
Enabling GPIO_FUNC_SPI_CS[1|2]_EN will claim the use of gpio pins 0 and 1
respectivelly for use as SPI CS pins.
When really needed, this can still be enabled on kernel hints using the
function_set and function_clear knobs.
This is derived from the mps(4) driver, but it supports only the 12Gb
IT and IR hardware including the SAS 3004, SAS 3008 and SAS 3108.
Some notes about this driver:
o The 12Gb hardware can do "FastPath" I/O, and that capability is included in
this driver.
o WarpDrive functionality has been removed, since it isn't supported in
the 12Gb driver interface.
o The Scatter/Gather list handling code is significantly different between
the 6Gb and 12Gb hardware. The 12Gb boards support IEEE Scatter/Gather
lists.
Thanks to LSI for developing and testing this driver for FreeBSD.
share/man/man4/mpr.4:
mpr(4) man page.
sys/dev/mpr/*:
mpr(4) driver files.
sys/modules/Makefile,
sys/modules/mpr/Makefile:
Add a module Makefile for the mpr(4) driver.
sys/conf/files:
Add the mpr(4) driver.
sys/amd64/conf/GENERIC,
sys/i386/conf/GENERIC,
sys/mips/conf/OCTEON1,
sys/sparc64/conf/GENERIC:
Add the mpr(4) driver to all config files that currently
have the mps(4) driver.
sys/ia64/conf/GENERIC:
Add the mps(4) and mpr(4) drivers to the ia64 GENERIC
config file.
sys/i386/conf/XEN:
Exclude the mpr module from building here.
Submitted by: Steve McConnell <Stephen.McConnell@lsi.com>
MFC after: 3 days
Tested by: Chris Reeves <chrisr@spectralogic.com>
Sponsored by: LSI, Spectra Logic
Relnotes: LSI 12Gb SAS driver mpr(4) added
platforms which do not use loaders or kernels that want to hardcode
options or for FDT passed in by loader.
Also fix a build issue by putting the kmdp variable accessed back under
the #ifdef FDT; we may wish to revisit decision in which case more
code needs changing.
Submitted by: brooks
the cpufreq code. Replace its use with smp_started. There's at least
one userland tool that still looks at the kern.smp.active sysctl, so
preserve it but point it to smp_started as well.
Discussed with: peter, jhb
MFC after: 3 days
Obtained from: Netflix
commit 003649d9622ce252a2794ae5891ee7e7c209caca
Author: Robert N. M. Watson <robert.watson@cl.cam.ac.uk>
Date: Wed Feb 5 18:32:09 2014 +0000
Teach the FreeBSD/beri boot to "auto-detect" whether argument 4 (a3) is a
memory size of pointer to a struct bootinfo * by looking at its value and
seeing whether it is pointer-like. If a pointer, assume it's a bootinfo
and extract memsize from it instead; otherwise, use it as memsize directly.
This allows kernels to support bootinfo being passed by loader (and boot2)
while still supporting older Miniboot setups.
commit f7045af9a1e92b6bd92541fe5d25abf66d824e8f
Author: Robert N. M. Watson <robert.watson@cl.cam.ac.uk>
Date: Thu Feb 6 13:45:34 2014 +0000
When the module metadata pointer is available from loader, use it in the
kernel.
commit 52e0e1ff2cba9dfcfab9e1d0a31fb7fdf7317450
Author: Robert N. M. Watson <robert.watson@cl.cam.ac.uk>
Date: Thu Feb 6 19:57:48 2014 +0000
In the BERI kernel boot code, extract 'boothowto' (which includes boot flags
such as '-s') and 'envp' from passed module data. Booting to single-user
mode using boot flags now works.
Sponsored by: DARPA, AFRL
boot/mips/beri/loader/metadata.c allow FDT configuration to set
command line options.
This leads to an interesting quesiton of future interactions with loader.
However for configurations without loader this allows bootverbose or boot
single user to be set by compiling a new kernel, which is good enough for
testing and debugging.
Reviewed by: rwatson
MFC after: 1 week
NetFPGA-10G Embedded CPU Ethernet Core.
The current version operates on a simple PIO based interface connected
to a NetFPGA-10G port.
To avoid confusion: this driver operates on a CPU running on the FPGA,
e.g. BERI/mips, and is not suited for the PCI host interface.
MFC after: 1 week
Relnotes: yes
Sponsored by: DARPA/AFRL
Remove the uart support in favour of a "jtag-uart" interface imitation
providing a much simpler interface, directly exported to the host,
allowing the toolchain to be shared with BERI on Altera. [1]
Submitted by: Jong Hun HAN (jong.han cl.cam.ac.uk) [1]
MFC after: 2 weeks
To reduce the diff struct pcu.cnt field was not renamed, so
PCPU_OP(cnt.field) is still used. pc_cnt and pcpu are also used in
kvm(3) and vmstat(8). The goal was to not affect externally used KPI.
Bump __FreeBSD_version_ in case some out-of-tree module/code relies on the
the global cnt variable.
Exp-run revealed no ports using it directly.
No objection from: arch@
Sponsored by: EMC / Isilon Storage Division
The NetBSD Foundation states "Third parties are encouraged to change the
license on any files which have a 4-clause license contributed to the
NetBSD Foundation to a 2-clause license."
This change removes clauses 3 and 4 from copyright / license blocks that
list The NetBSD Foundation as the only copyright holder.
Sponsored by: The FreeBSD Foundation
chips have more.
So for now, let's allow more. We should teach the apb code to just
reject interrupts that lie outside what the chip can do at runtime.
later. If the interrupts are ACKed even if they're not masked, we get
the interrupts again later. Grr.
* The AR724x and later chips want the interrupt bits cleared by writing the
relevant bit to it, NOT by writing all but the current interrupt to it.
Tested:
* AR9344, DB120 reference board
TODO:
* Test ar724x and later chips to ensure no regressions have occured.
'eeprommac'.
The existing driver would just make arge units past 0 take the primary
MAC and increment it by the unit number, without correct address wrapping.
That has to be fixed at a later date.
Tested:
* Atheros DB120 reference obard
