The kbd, kbdmux, ugen and uhid drivers included <sys/tty.h>, because
they needed clists, which have been moved to <sys/clist.h> some time
ago. In the MPSAFE TTY branch, <sys/tty.h> does not include
<sys/clist.h>, which means we have to teach these drivers to include
this header file directly.
Approved by: philip (mentor, implicit)
behavior. Specifically, probe Host-PCI bridges in the order they are
encountered in the tree. For CPUs, just use an order of 100000 and assume
that no Host-PCI bridges will be more than 10000 levels deep in the
namespace. This fixes an issue on some boxes where the HPET timer stopped
attaching.
used but MSI to HyperTransport IRQ mapping is enabled, and would act as
if MSI is turned on, resulting in interrupt loss.
This commit will,
1. enable MSI mapping on a device only when MSI is enabled for that
device and the MSI address matches the HT mapping window.
2. enable MSI mapping on a bridge only when a downstream device is
allocated an MSI address in the mapping window
PR: kern/118842
Reviewed by: jhb
MFC after: 1 week
kthread of the mpt(4) driver that hangs around for the entire lifetime of
the thread. Previously the driver would allocate a new CCB using M_WAITOK
with a lock held each time it updated its state. While here, use the
CAM API for allocating a CCB rather than raw malloc(9).
Reviewed by: scottl
MFC after: 1 week
and handle NIC hardware watchdog resets.
- remove buggy code at the top of mxge_tick() which tried
to detect a race which is already detected in the kernel's
callout code.
- move callout_stop() and callout_reset() into mxge_close()
mxge_open() rather than doing the callout manipulation
all over the place.
- use callout_drain(), rather than callout_stop() to prevent
a potential race between mxge_tick() and mxge_detach()
which could lead to softclock using a destroyed mutex
- restructure the mxge_tick() and mxge_watchdog_reset()
routines to avoid resetting a callout, and then
immediately stopping it if the watchdog reset routine
is called, and fails.
- enable the driver to handle NIC hardware watchdog
resets by restoring the NIC's PCI config space, which is
lost when the NIC hardware watchdog triggers.
Reviewed by: jhb (previus version)
vr(4) overhauling(r177050).
It seems that filtering multicast addresses with multicast CAM
entries require accessing 'CAM enable bit' for each CAM entry.
Subsequent accessing multicast CAM control register without
toggling the 'CAM enable bit' seem to no effects.
In order to fix that separate CAM setup from CAM mask configuration
and CAM entry modification. While I'm here add VLAN CAM filtering
feature which will be enabled in future(FreeBSD now can receive
VLAN id insertion/removal event from vlan(4) on the fly).
For VT6105M hardware, explicitly disable VLAN hardware tag
insertion/stripping and enable VLAN CAM filtering for VLAN id 0.
This shall make non-VLAN frames set VR_RXSTAT_VIDHIT bit in Rx
status word.
Added multicast/VLAN CAM address definition to header file.
PR: kern/125010, kern/125024
MFC after: 1 week
years. All datasheet I have indicates the bit 15 is the
VR_RXSTAT_RX_OK. The bit 14 is reserved for all Rhine family
except VT6105M. VT6105M uses that bit to indicate a VLAN frame
with matching CAM VLAN id.
Use the VR_RXSTAT_RX_OK instead of VR_RXSTAT_RXERR when vr(4)
checks the validity of received frame.
This should fix occasional dropping frames on VT6105M.
Tested by: Goran Lowkrantz ( goran.lowkrantz at ismobile dot com )
MFC after: 1 week
1. The FreeBSD driver was setting an interrupt coalesce delay of 1000us
for reasons that I can only speculate on. This was hurting everything
from lame sequential I/O "benchmarks" to legitimate filesystem metadata
operations that relied on serialized barrier writes. One of my
filesystem tests went from 35s to complete down to 6s.
2. Implemented the Performant transport method. Without the fix in
(1), I saw almost no difference. With it, my filesystem tests showed
another 5-10% improvement in speed. It was hard to measure CPU
utilization in any meaningful way, so it's not clear if there was a
benefit there, though there should have been since the interrupt handler
was reduced from 2 or more PCI reads down to 1.
3. Implemented MSI-X. Without any docs on this, I was just taking a
guess, and it appears to only work with the Performant method. This
could be a programming or understanding mistake on my part. While this
by itself made almost no difference to performance since the Performant
method already eliminated most of the synchronous reads over the PCI
bus, it did allow the CISS hardware to stop sharing its interrupt with
the USB hardware, which in turn allowed the driver to become decoupled
from the Giant-locked USB driver stack. This increased performance by
almost 20%. The MSI-X setup was done with 4 vectors allocated, but only
1 vector used since the performant method was told to only use 1 of 4
queues. Fiddling with this might make it work with the simpleq method,
not sure. I did not implement MSI since I have no MSI-specific hardware
in my test lab.
4. Improved the locking in the driver, trimmed some data structures.
This didn't improve test times in any measurable way, but it does look
like it gave a minor improvement to CPU usage when many
processes/threads were doing I/O in parallel. Again, this was hard to
accurately test.
it in detail.
When setting media, don't error out when a specific media is selected.
# Note: There may be some issues still here since the EtherJet PC Card doesn't
# conform to the datasheet. Many different kinds of dongles can be plugged in
# and it is unknown how to ask which one it is.
Also, add a /* bad! */ comment to a 1/2 second delay after we set the
DC/DC parameters. This should be a *sleep of some sort for !cold.
Fortunately it is the only one and is only used when setting media, so
the benefit from removing it is small. Unfortunately, it likely
serves as an exemplar of good programming techniques, which it isn't.
when it worked as generic IDE.
PR: 125422
Submitted by: Andrey V. Elsukov <bu7cher at yandex dot ru>
Approved by: imp (mentor, implicit)
MFC after: 1 week
generation of RTL810x PCIe fast ethernet controller. Note, Tx/Rx
descriptor format is different from that of first generation of
RTL8101E series. Jumbo frame is not supported for RTL810x
family.
Tested by: NAGATA Shinya ( maya AT negeta DOT com )
mutexes and replacing the obsolete if_watchdog interface. The ndis_ticktask
function calls into ieee80211_new_state under one condition with NDIS_LOCK
held. The ieee80211_new_state would call into ndis_start in some cases too,
resulting in the occasional case where ndis_start acquires NDIS_LOCK from
inside the NDIS_LOCK held by ndis_ticktask.
Obtained from: Paul B. Mahol <onemda@gmail.com>
MFC after: 1 week
appropriate (versions not appropriate to merge omitted):
o 1.226 imp nop, save for NetBSD string (minor merging the other way)
o 1.225 jnemeth Coreage LAPCCTXD
o 1.224 martin (remove 3rd and 4th clauses)
o 1.223 kiyohara (TDK bluetooth PC Card)
o 1.222 kiyohara (Anycom BlueCard)
o 1.221 ichiro (NEC Infrontia AX420N)
o 1.219 jmcneill (EDIMAX EP-4101)
o 1.213 tsutsui (TEAC IDECARDII entry fix)
Also, while I'm here, fix some tab problems that have crept in.
Our hook creates the sysctl node before root is mounted, but after cpu
is probed. It seems that k8temp can be loaded before the cpu module and,
in those cases, dev.cpu.0.temperature was not created.
PR: 124939
global symbols, such as raw_input and raw_output, to have lmc_ prefixes.
This doesn't affect actual functionality since the functions are static,
but will limit the opportunities for current confusion and future
difficulty.
MFC after: 3 days
to global hostname and domainname variables. Where necessary, copy
to or from a stack-local buffer before performing copyin() or
copyout(). A few uses, such as in cd9660 and daemon_saver, remain
under-synchronized and will require further updates.
Correct a bug in which a failed copyin() of domainname would leave
domainname potentially corrupted.
MFC after: 3 weeks
AcpiEvaluateObject() calls, otherwise, we are not able to bring devices
back up (NULL means 0, hence always off).
While there add missing WLAN on/off support.
MFC after: 3 days
Pointy hat to: rpaulo
MPSAFE patches on current@ and stable@. This driver also has a fundamental
issue in that it sleeps when sending commands to the card including in the
if_init/if_start routines (which can be called from interrupt context). As
such, the driver shouldn't be working reliably even on 4.x.
- Add a mutex to the softc and use it to protect the softc and device
hardware.
- Setup interrupt handler after ether_ifattach().
- Remove unused sbsh_watchdog() routine.
- Protect against concurrent attempts to load firmware.
- Add a mutex to the softc and use it to protect the softc and device
hardware.
- Setup interrupt handler after attaching device to network stack.
- Use device_set_desc() rather than device_quiet() plus a manual printf
that simulates the normal probe printf.
- Axe next_sbni_unit and instead just leave room for two sbni devices for
each bus attachment.
- Don't bzero the already-zero'd softc.
- Add a detach method to the PCI driver.
- Add a lock to protect the list of available devices used to chain
interrupt handlers for dual port ISA cards.
- Remove unused watchdog routine.
- If if_alloc() fails, make sbni_attach() return an error rather than
panic'ing.
- Consolidate code to free bus resources into sbni_release_resources().
- Clear IFF_DRV_RUNNING|OACTIVE in stop() routine instead of in callers.
- Let ether_ioctl() handle SIOCSIFMTU.
and stable@. It also is a driver for an older non-802.11 wireless PC card
that is quite slow in comparison to say, wi(4). I know Warner wants this
driver axed as well.
- Add a mutex to the softc and use it to lock the softc and device hardware.
- Use a private timer to replace if_watchdog/if_timer.
- Use if_printf() rather than if_xname.
- Setup interrupt handler after ether_ifattach().
- Add a mutex to the softc and use it to protect the softc and device
hardware.
- Setup interrupt handler after ether_ifattach().
- Use a private timer instead of if_timer/if_watchdog.
- Retire arl_unit from the softc and use if_printf() and device_printf()
instead.
Note that the unpatched driver in 6.x and later does not work with the
hardware, so the one person who had volunteered to test the patch wasn't
able to test it.
dispatched without Giant, and add NETISR_FORCEQUEUE, which allows specific
netisr handlers to always be dispatched via a queue (deferred). Mark the
usb and if_ppp netisr handlers as NETISR_FORCEQUEUE, and explicitly
acquire Giant in those handlers.
Previously, any netisr handler not marked NETISR_MPSAFE would necessarily
run deferred and with Giant acquired. This change removes Giant
scaffolding from the netisr infrastructure, but NETISR_FORCEQUEUE allows
non-MPSAFE handlers to continue to force deferred dispatch so as to avoid
lock order reversals between their acqusition of Giant and any calling
context.
It is likely we will be able to remove NETISR_FORCEQUEUE once
IFF_NEEDSGIANT is removed, as non-MPSAFE usb and if_ppp drivers will no
longer be supported.
Reviewed by: bz
MFC after: 1 month
X-MFC note: We can't remove NETISR_MPSAFE from stable/7 for KPI reasons,
but the rest can go back.
ATM Tx/Rx checksum offload is supported but TSO and jumbo frame is
not yet supported. Because these newer controllers use different
descriptor formats, a flag RL_FLAG_DESCV2 flag was introduced to
handle that case in Tx/Rx handler. Also newer controllers seems to
require to not touch 'enable Tx/Rx bit' in RL_CPLUS_CMD register
so don't blindly try to set that bits.
Note, it seems that there is still power-saving related issue where
driver fails to attach PHY. Rebooting seems to fix that issue but
number of required reboots varys.
Many thanks to users that helped during developement. I really
appreciate their patient and test/feedbacks.
a dedicated flag that represents controller capabilities/events.
This will simplify many part of code that requires different
workaround for each controller revisions and will enhance
readability.
While I'm here move PHY wakeup code up before mii_phy_probe() which
seems to help to wake PHY in some cases.
RL_TXCFG register to identify a device in device probe. Reflect the
fact by modifing device description with general ethernet
controller family.
Note, rl_basetype in struct rl_type is not used and the more
detailed information is provided with rl_hwrev structure.
Previously we reused the space in the request buffer after the request
header to hold config pages during a transaction. This does not work when
reading large pages however. Also, we were already malloc'ing a buffer to
do a copyin/copyout w/o holding locks that was then copied into/out of the
request buffer. Instead, go ahead and use bus dma to alloc a buffer for
each config page request (and RAID actions that have an associated
ActionSGE). This results in fewer data copies and allows for larger sized
requests. For now the maximum size of a request is arbitrarily limited to
16 MB.
MFC after: 2 weeks
Adaptec RAID 2045
Adaptec RAID 2405
Adaptec RAID 2445
Adaptec RAID 2805
Without this change these devices are supported by the driver's family
support, but they then appear as "Adaptec RAID Controller" in boot
messages and the dev.aac.0.%desc sysctl.
This includes hotkeys support and sysctl variables to control camera
and card reader. These new sysctls don't have CTFLAG_ANYBODY set.
While there add entries to devd.conf related to the Eee volume keys.
Reviewed by: phillip
MFC after: 1 week
Also tested by: lme (previous version)
- Each log entry contains a text description in the "description" field of
the entry. The existing decode logic always ended up duplicating
information that was already in the description string. This made the
logs overly verbose. Now we just print out the description string.
- Add some simple parsing of the timestamp and event classes.
Reviewed by: ambrisko, scottl
MFC after: 2 weeks
- Fetch events from the controller in batches of 15 rather than a single
event at a time.
- When fetching events from the controller, honor the event class and
locale settings (via hw.mfi tunables). This also allows the firmware to
skip over unwanted log entries resulting in fewer requests to the
controller if there many unwanted log entries since the last clean
shutdown.
- Don't drop the driver mutex while decoding an event.
- If we get an error other than MFI_STAT_NOT_FOUND (basically EOF for
hitting the end of the event log) then emit a warning and bail on
processing further log entries.
Reviewed by: ambrisko, scottl
MFC after: 2 weeks
Now that st_rdev is being automatically generated by the kernel, there
is no need to define static major/minor numbers for the iodev and
memdev. We still need the minor numbers for the memdev, however, to
distinguish between /dev/mem and /dev/kmem.
Approved by: philip (mentor)
problem where Adaptec's arcconf monitoring tool hangs after producing
its expected output.
Submitted by: Adaptec, via driver ver 15317
MFC after: 1 week
from the softc.
- Rework the watchdog timer to match other NIC drivers:
- Start a timer in fe_init() that runs once a second and checks a counter
in the softc that is identical to the deprecated 'if_timer'.
- Just adjust the softc tx timeout value when sending packets instead of
scheduling the timer.
- Use IFQ_SET_MAXLEN().
Tested by: WATANABE Kazuhiro
some time now so collapse calls accordingly.
o Given that gem_load_txmbuf() is allowed to fail resulting in a packet
drop also for quite some time now implement the functionality of
gem_txcksum() by means of m_pullup(9), which de-obfuscates the code
and allows to always retrieve the correct length of the IP header.
o Add missing BUS_DMASYNC_PREREAD when syncing the control DMA maps in
gem_rint() and gem_start_locked().
o Correct some bus_barrier(9) calls to do a read/write barrier as we
do a read after a write. Add some missing ones in gem_mii_readreg()
and gem_mii_writereg().
o According to the Apple GMAC driver, the GEM ASIC specification and
the OpenSolaris eri(7D) the TX FIFO threshold has to be set to 0x4ff
for the Gigabit variants and 0x100 for the ERI in order do avoid TX
underruns.
o In gem_init_locked():
- be conservative and enable the RX and TX MACs,
- don't clear GEM_LINK otherwise we don't ever mark the link as up
again if gem_init_locked() is called from gem_watchdog(),
- remove superfluous setting of sc_ifflags.
o Don't bother to check whether the interface is running or whether its
queue is empty before calling gem_start_locked() in gem_tint(), the
former will check these anyway.
o Call gem_start_locked() in gem_watchdog() in order to try to get
some more packets going.
o In gem_mii_writereg() after reseting the PCS restore its configuration.
GMAC testing: grehan, marcel
MFC after: 2 weeks
- Add a mutex to the softc to protect the softc and device hardware.
- Use a private watchdog timer.
- Setup interrupt handler after ether_ifattach().
- Use bus_foo() rather than bus_space_foo() and remove bus space tag and
handle from softc.
Tested by: imp
Except for the case where we use the cloner library (clone_create() and
friends), there is no reason to enforce a unique device minor number
policy. There are various drivers in the source tree that allocate unr
pools and such to provide minor numbers, without using them themselves.
Because we still need to support unique device minor numbers for the
cloner library, introduce a new flag called D_NEEDMINOR. All cdevsw's
that are used in combination with the cloner library should be marked
with this flag to make the cloning work.
This means drivers can now freely use si_drv0 to store their own flags
and state, making it effectively the same as si_drv1 and si_drv2. We
still keep the minor() and dev2unit() routines around to make drivers
happy.
The NTFS code also used the minor number in its hash table. We should
not do this anymore. If the si_drv0 field would be changed, it would no
longer end up in the same list.
Approved by: philip (mentor)
mtx interface for NDIS_LOCK/UNLOCK. This should result in less
CPU utilization on behalf of the ndis driver. Additionally, this
commit also fixes a potential LOR in the ndis_tick code, by
not locking inside the ndis_tick function, but instead delegating
that work to the helpers called through IoQueueWorkItem. The
way that this is currently set up for NDIS prevents us from
simply implementing a callout_init_mtx mechanism.
However, the helper functions that handle the various timeout
cases implement fine-grained locking using the spinlocks provided
by the NDIS-compat layer, and using the mtx that is added with
this commit. This leaves the following ndis_softc members operated
on in ndis_tick in an unlocked context:
* ndis_hang_timer - Only modified outside of ndis_tick once, before
the first callout_reset to schedule ndis_tick
* ifp->if_oerrors - Only incremented in two places, which should be
an atomic op
* ndis_tx_timer - Assigned to 5 (when guaranteed to be 0) or 0
(in txeof), to indicate to ndis_tick what to
do. This is the only member of which I was
suspicious for needing the NDIS_LOCK here. My
testing (and another's) have been fine so far.
* ndis_stat_callout - Only uses a simple set of callout routines,
callout_reset only called by ndis_tick after
the initial reset, and then callout_drain is
used exactly once in shutdown code.
The benefit is that ndis_tick doesn't acquire NDIS_LOCK unless one of
the timeout conditions is flagged, and it still obeys the locking
order semantics that are dictated by the NDIS layer at the moment. I
have been investigating a more thorough s/spinlock/mtx/ of the NDIS
layer, but the simplest naive approach (replace KeAcquireSpinLock
with an mtx implementation) has anti-succeeded for me so far. This
is a good first step though.
Tested by: onemda@gmail.com
Reviewed by: current@, jhb, thompsa
Proposed by: jhb
We still use the interrupt filter due to performance problems that show up if
we don't. The main problem seen is that, due to the interrupt being edge
triggered, we occasionally miss interrupts which leads us to not notice that
we can transmit more packets. Using the new approach, which just schedules
a task on a taskqueue, we are guaranteed to have the task run even if the
interrupt arrived while we were already executing. If we were to use an
ithread the system would mask the interrupt while the handler is run and we'd
miss interrupts.
- Add a mutex to the softc to protect the softc and device hardware.
- Use a private timer to implement a watchdog for tx timeouts and drive
the timer for auto negotiation.
- Use bus_foo() rather than bus_space_foo() and remove the bus space
tag & handle from the softc.
- Call bus_setup_intr() after ether_ifattach().
Tested by: Florian Smeets flo of kasimir.com
Remove the code which disables port status change interrupts for 1s
when one occured -- this makes that events get lost or delayed until
the next change.
Obtained from: NetBSD
- Fixed a problem on i386 architecture when using split header/jumbo frame
firmware caused by hardware alignment requirements.
- Added #define BCE_USE_SPLIT_HEADER to allow the feature to be enabled/
disabled. Enabled by default.
PR: kern/123696
MFC after: 2 weeks
In the FreeBSD base system, there are only two utilities that use struct
tty, namely pstat and sicontrol. The sicontrol utility calls the
TCSI_TTY ioctl(), which copies struct tty back to userspace.
sicontrol should not have this functionality. The same data is already
provided by pstat. If we really want to be able to export these numbers
through a file descriptor to userspace, we can export struct xtty, which
should provide a better abstraction. The ttystat option was only used as
a debugging aid.
This makes sicontrol compile in the mpsafetty branch.
Reviewed by: peter
Approved by: philip (mentor)
is in little endian form. Likewise setting DC_AL_PAR0/DC_AL_PAR1
register expect the address to be in little endian form. For big
endian architectures the address should be swapped to get correct
one.
Change setting/getting ethernet hardware address to big endian
architecture frendly.
Reported by: Robert Murillo ( billypilgrim782001 at yahoo dot com )
Tested by: Robert Murillo ( billypilgrim782001 at yahoo dot com )
some longstanding issues:
o pass the vap since it's now the "coin of the realm" and required
to do things like set initial tx parameters in private node
state for use prior to association
o pass the mac address as cards that maintain outboard station
tables require this to create an entry (e.g. in ibss mode)
o remove the node table reference, we only have one node table
and it's unlikely this will change so this is not needed to
find the com structure
- Store the softc of the device in the 'si_drv1' of the cdev.
- Lookup the softc via 'si_drv1' in cdev methods rather than using the
minor number as a unit for devclass_get_softc().
- Lookup the device_t via the softc field in cdev methods rather than
using the minor number as a unit for devclass_get_device().
- Add a mutex to the softc to protect 'sc_opened'.
- Remove D_NEEDGIANT as all the smbus drivers are now MPSAFE and this driver
is now MPSAFE.
- Remove some checks for NULL softc pointers that can't happen and don't
bzero the softc during attach.
it. Bad imp. Removing us dips us under 10,000 in size too.
o Replace an unconditional 30ms DELAY (yes, busy wait) with a check of the
SIBUSY bit in the SelfST register before accessing the eeprom. This changes
the time to read the EEPROM from 2 * 20 * 30ms (1.2s) to < 20*25us (.0005s)
and make the attach of the card tolerable when ethernet media is present.
Include data from the datasheet about why this works. While this is a 2500x
speed increase, it doesn't really matter at all once the card is probed...
o set dev earlier in softc.
o remove unused fields from softc and args from cs_alloc_irq
o remove some commented code that will never be implemented.
o Don't try to send a packet and see if it worked. We don't
need this anymore, and it doesn't add any value.
o tweaks for BNC and AUI.
o limit possible time hung in the kernel to 4s rather than 40s.
sn(4) driver and also looking at newer drivers. The reason for the rewrite is
to support MII and to try and resolve some performance issues found when trying
to use the sn(4) driver on the Gumstix network boards.
For reference, the SMSC LAN91C111 is a non-PCI ethernet part whose lineage
dates back to Ye Olde Days of ISA. It seems to get some use in the embedded
space these days on parts lacking on-board MACs or on-board PCI controllers,
such as the XScale PXA line of ARM CPUs.
This also includes a driver for the SMSC LAN83C183 10/100 PHY.
Man page to follow.
they can re-added. Remove CS_NAME. Don't whine when there's an
ignored checksum error: User has said STFU, so we should S the FU.
(remove mandated properties).
- Add a mutex to the softc to protect the softc and the device hardware.
- Add a private timer to manage transmit watchdogs rather than using
if_timer/if_watchdog.
- Setup the interrupt handler after ether_ifattach().
Tested by: imp
for this driver is called 'ie'. Otherwise, ifconfig(8) doesn't recognize
any of the modules as being the ie(4) driver and will always try to kldload
the driver even when it is already present in the kernel.
Reported by: Thierry Herbelot
10BaseT' since it required 10BaseT to have carrier to switch to it.
This chip makes it hard to do proper auto, so we don't do it. We
can't test carrier on things easily.
Don't insist on carrier when we set the media. Don't report failures.
Remove a 1s! delay that appears to not be needed.
With these patches, and John Baldwin's patches, I'm able to pass
packets on my IBM EtherJet card again.
MAC events.
- Use bus_*() rather than bus_space_*() and remove the bus space tag and
handle from the softc.
- Retire unused macros for examining CIS tuples.
o When forced to be 10baseT, don't require that the 10baseT interface
have link to succeed. Still require it for IFM_AUTO, however, since it
appears that there's no way to tell if a specific type of interface
worked. I'm doing a web search for a datasheet now to see if there's
anything obvious.
o Minor incidental formatting nits, including collapsing code of the form
if (foo) {
bar();
} else {
if (baz)
bing();
}
into:
if (foo) {
bar();
} else if (baz) {
bing();
}
to save an indentation level.
o Remove stray reference to 3.x config file syntax.
# I believe John's patches still apply after this...
timer by keeping a once-a-second timer running that decrements a counter
similar to if_timer and reset the chip if it gets down to zero via the
decrement.
- Use IFQ_SET_MAXLEN().
systems where the CardBus bridge was connected to a APIC. The case
where the probe routine is told to not setup the IRQ was mishandled
but the error was masked in the case where the IRQ was a valid one
for the card.
MFC after: 1 week
bring it more up to date. The watchdog timer, and its
associated code, is all collapsed into the ndis_tick function
that was implemented for the NDIS-subsystem watchdog. This
implementation is similar to what numerous other drivers use
to implement the watchdog.
Reviewed by: thompsa, jhb
MFC after: 2 weeks
- Add a mutex to the softc to protect the softc and device hardware.
- Don't leak bus resources if if_alloc() fails during attach.
- Setup the interrupt handler after calling ether_ifattach().
- Use a private timer to manage the transmit watchdog.
Tested by: WATANABE Kazuhiro CQG00620 of nifty.ne.jp
- Add a mutex to protect the softc and device hardware.
- Use a callout rather than a callout_handle for the media timer.
- Use a dedicated timer for managing the tx watchdog rather than if_timer.
- Fix some resource leaks if xe_attach() fails.
- Shutdown the device before detaching the driver.
- Setup the interrupt handler after ether_ifattach().
Tested by: Ian FREISLICH ianf of clue.co.za
- Add a mutex to the softc and use it to protect the softc and device.
- Setup the interrupt handler in the common code instead of in each front
end and do it after ether_ifattach().
- Use ie_stop() and ieinit_locked() in iereset() rather than frobbing IFF_UP
and invoking ieioctl().
- Use DELAY() to implement a spin loop on a register with a timeout rather
than scheduling a timeout and then doing a tight spin on the register.
In the non-MPSAFE case this would never have worked because the spinning
code held Giant and the timeout routine would have been blocked on Giant
forever. The same approach would not worke in the MPSAFE case either for
the same reason, hence use a loop around DELAY().
- Clear IFF_DRV_(RUNNING|OACTIVE) in ie_stop() rather than in callers.
- Call ieinit_locked() directly rather than ieioctl(!) from ie_mc_reset().
- Don't leak the rx frame buffer on detach.
Tested by: Thierry Herbelot thierry of herbelot.com
pretend to be IntelliMouse (which have a few more features than generic mice)
causing the IntelliMouse probe to work and the Synaptics code never to be
called.
This should not break "real" IntelliMouse because the Synaptics detection code
is fairly specific.
PR: kern/120833
Submitted by: Eygene Ryabinkin <rea-fbsd -at- codelabs.ru>
MFC after: 1 week
variations from normal 16x50 behaviour however is the the use of a normally
unused bit of IER to control RX timeout interrupts independently of the
generally used RXRDY bit. If this bit is not enabled, we only ever get
interrupts when the FIFO is full, never before. This is not very useful when
the UART is being used as a console.
In order to support this without causing potential problems on more "normal"
16x50 variants, this change introduces two hints for the uart device, ier_mask
and ier_rxbits. These can be used to override which bits get set and cleared
when we're enabling and disabling RX interrupts.
Reviewed by: marcel
Even though we got rid of device major numbers some time ago, device
drivers still need to provide unique device minor numbers to make_dev().
These numbers are only used inside the kernel. They are not related to
device major and minor numbers which are visible in devfs. These are
actually based on the inode number of the device.
It would eventually be nice to remove minor numbers entirely, but we
don't want to be too agressive here.
Because the 8-15 bits of the device number field (si_drv0) are still
reserved for the major number, there is no 1:1 mapping of the device
minor and unit numbers. Because this is now unused, remove the
restrictions on these numbers.
The MAXMAJOR definition was actually used for two purposes. It was used
to convert both the userspace and kernelspace device numbers to their
major/minor pair, which is why it is now named UMINORMASK.
minor2unit() and unit2minor() have now become useless. Both minor() and
dev2unit() now serve the same purpose. We should eventually remove some
of them, at least turning them into macro's. If devfs would become
completely minor number unaware, we could consider using si_drv0 directly,
just like si_drv1 and si_drv2.
Approved by: philip (mentor)
clocked at 10x normal speed. That is, when you set it for 9600
baud, it actually does 96000 baud. In order to make it plug and
play with other serial ports, it has to have its clock rate
reduced by a factor of 10.
Discussed with: Marcel Moolenaar
MFC after: 2 weeks
o do not put the chip into full sleep in ath_stop as it gains
nothing and causes many parts to hang in ath_detach because we
may touch the chip during vap teardown; this may also fix issues
with unloading the module
o add a note in ath_detach to explain ath_hal_detach puts the
chip in low power mode; this is useful to know as it means
unloading the module will place a pci device in the lowest
possible power state
o leave an #ifdef notyet marker for powering down the chip when
a device is marked down; we can't do that until we handle all
the ways the driver may be entered and touch the chip
o fix resume by reloading the h/w key cache as it's been clobbered
(for pci) by the socket being powered off; for station mode we
directly stop+init the chip and then simulate a beacon miss to
get the upper layers sync'd up; for other configs we must brute
force stop+start the vaps so they go through the state machine
on amd64. Note the only difference is the iovec32 part so I use the
native structure for everything else.
Also I plan to MFC all the changes in -current to 7-stable and 6-stable
shortly since I've been running them. This does not include the cam
changes.
MFC after: 3 days
calling destroy_dev() with sleepable malloc(9). The entire opetation
is being serialized through pcm cv from top down, so dropping mutex is
rather safe.
Reported by: delphij
gigabit ethernet and JMC260 fast ethernet controllers. ATM jme(4)
supports all hardware features except RSS and multiple Tx/Rx queue.
In these days most ethernet controller vendors take a ply of
concealing hardware detailes from open source developers. As
contrasted with these vendors JMicron provided all necessary
information needed to write a stable driver during driver writing
and answered many questions I had. They even helped fixing driver
bugs with protocol analyzer. Many thanks to JMicron for their
support of FreeBSD.
H/W donated by: JMicron
context, where the iwn mutex is being held, and
iwn_start assumes that we do not have that mutex held.
Resolve this issue with what we do for other NICs by
splitting the iwn_start procedure into two parts,
iwn_start() do the locking, and iwn_start_locked()
assumes that the mutex is being held. This resolves
panic when WITNESS is enabled.
NET_NEEDS_GIANT. netatm has been disconnected from the build for ten
months in HEAD/RELENG_7. Specifics:
- netatm include files
- netatm command line management tools
- libatm
- ATM parts in rescue and sysinstall
- sample configuration files and documents
- kernel support as a module or in NOTES
- netgraph wrapper nodes for netatm
- ctags data for netatm.
- netatm-specific device drivers.
MFC after: 3 weeks
Reviewed by: bz
Discussed with: bms, bz, harti
the watchdog code. This delta also incorporates some missing PCI
IDs that got added.
PR 122928 - might be fixed by this, no verification at this point.
controller. L1 has several threshold/timer registers and they
seem to require careful tuned parameters to get best
performance. Datasheet for L1 is not available to open source
driver writers so age(4) focus on stability and correctness of
basic Tx/Rx operation. ATM the performance of age(4) is far from
optimal which in turn means there are mis-programmed registers or
incorrectly configured registers.
Currently age(4) supports all known hardware assistance including
- MSI support.
- TCP Segmentation Offload.
- Hardware VLAN tag insertion/stripping.
- TCP/UDP checksum offload.
- Interrupt moderation.
- Hardware statistics counter support.
- Jumbo frame support.
- WOL support.
L1 gigabit ethernet controller is mainly found on ASUS
motherboards. Note, it seems that there are other variants of
hardware as known as L2(Fast ethernet) and newer gigabit ethernet
(AR81xx) from Atheros. These are not supported by age(4) and
requires a seperate driver. Big thanks to all people who reported
feedback or tested patches.
Tested by: kevlo, bsam, Francois Ranchin < fyr AT fyrou DOT net >
Thomas Nystroem < thn AT saeab DOT se >
Roman Pogosyan < asternetadmin AT gmail DOT com >
Derek Tattersal < dlt AT mebtel DOT net >
Oliver Seitz < karlkiste AT yahoo DOT com >
-It has new hardware support
-It uses a new method of TX cleanup called Head Write Back
-It includes the provisional generic TCP LRO feature contributed
by Myricom and made general purpose by me. This should move into
the stack upon approval but for this driver drop its in here.
-Also bug fixes and etc...
MFC in a week if no serious issues arise.
so the index needs to be translated into an offset. While we
did add the offset (0x10), we forgot to account for the width.
Tested by: Thomas Vogt
MFC after: 3 days
- Obsolete redundant inst_name and unit members of struct sym_hcb.
- Fix three more NULL vs. 0 confusions.
- Use device_set_softc(9) to tell the bus layer that this driver
allocates a instance of struct sym_hcb itself.
- Rename BGE_FLAG_EEPROM to BGE_FLAG_EADDR to underline it's absence means
"there's no chip containing an Ethernet address fitted to the BGE chip
so we have to get it from the firmware instead" rather than "there's no
EEPROM, but maybe NVRAM or something else".
- Don't treat BCM5906[M] generally like chips w/o BGE_FLAG_EADDR set, just
in the two cases really necessary. This gets us line with the original
patch for DragonFlyBSD.
- For sparc64 restore the intended behavior of obtaining the Ethernet
address from the firmware in case BGE_FLAG_EADDR is not set, even for
BCM5906[M].
- Fix some style(9) bugs introduced with rev. 1.208 of if_bge.c
Approved by: jhb
Additional testing by: Thomas Nystroem (BCM5906)
Add support for the Apple USB Ethernet adapter.
Work around the "latch in at the first working PHY address hack",
that fails for this adapter because it returns 0xffff when reading
from lower PHY addresses. Also add more debugging printfs
Obtained from: OpenBSD
MFC After: 3 days
o correct mapping of CCK rates to PLCP; was using nonstandard Ralink
values which just happened to also be used by Zydas (so went unnoticed)
o change ieee80211_plcp2rate api to take a phy type instead of a flag
that indicates ofdm/!ofdm
o update drivers to match (restore per-driver code to map rate->PLCP)
Reviewed by: sephe, weongyo, thompsa
o add IEEE80211_C_STA capability to indicate sta mode is supported
(was previously assumed) and mark drivers as capable
o add ieee80211_opcap array to map an opmode to the equivalent capability bit
o move IEEE80211_C_OPMODE definition to where capabilities are defined so it's
clear it should be kept in sync (on future additions)
o check device capabilities in clone create before trying to create a vap;
this makes driver checks unneeded
o make error codes return on failed clone request unique
o temporarily add console printfs on clone request failures to aid in
debugging; these will move under DIAGNOSTIC or similar before release
Instead use the worldwide known MAX() function.
This should fix problems with negative values showing up on
dev.cpu.%d.temperature.
This is slightly different from the fix in the PR.
Submitted by: KOIE Hidetaka <hide at koie.org>
PR: 123542
Handle cases where dma function pointers may be NULL, and where
the max_iosize can't be derived from a DMA data structure. For
the latter, revert to the prior behaviour of using DFLTPHYS for
the max i/o size when there is no other data.
Reviewed by: marcel
No objection by: sos
aligned on an 8 byte boundary. Prior to rev 1.36 this wasn't a problem
because mbuf clusters tend be naturally aligned. The switch to using
split buffers with the first buffer being the embedded data area of the
mbuf has broken this assumption, at least on i386, causing a complete
failure of RX functionality. Fix this for now by using a full cluster for
the first RX buffer. A more sophisticated approach could be done with the
old buffer scheme to realign the m_data pointer with m_adj(), but I'm also
not clear on performance benefits of this old scheme or the performance
implications of adding an m_adj() call to every allocation.
perform various operations on a controller. Specifically, for each mpt(4)
device, create a character device in devfs which accepts ioctl requests for
reading and writing configuration pages and performing RAID actions.
MFC after: 1 week
Reviewed by: scottl
