Commit was temporary fix due to rman_res_t defined as 32-bit u_long.
After redefining it as 64-bit variable workaround is not needed and
was removed.
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential revision: https://reviews.freebsd.org/D6214
Pressing the PEK (power enable key) will shutdown the board.
Some events are reported to devd via system "PMU" and subsystem
"Battery", "AC" and "USB" such as connected/disconnected.
Some sensors values (power source voltage/current) are reported via
sysctl (dev.axp209_pmu.X.)
It also expose a gpioc node usable in kernel and userland. Only 3 of
the 4 GPIO are exposed (The GPIO3 is different and mostly unused on
boards). Most popular boards uses GPIO1 as a sense pin for OTG power.
Add a dtsi file that adds gpio-controller capability to the device as
upstream doesn't defined it and include it in our custom DTS.
Reviewed by: jmcneill
Approved by: cognet (mentor)
Differential Revision: https://reviews.freebsd.org/D6135
return value when it could return 1 (indicating we should stop).
Fix a few instances of pager_open() / pager_close() not being called.
Actually use these routines for the environment variable printing code
I just committed.
PCIe PHY needs different initialization on MT7628/MT7688 SoCs than it does
on MT7620.
However, LEDE (and OpenWRT) dts files have the PCIe node for MT7628/MT7688
as compatible with mt7620-pci.
We already can handle this properly in our driver, so we just need to add
compat strings to fbsd-mt7628an.dtsi and the PCIe driver.
Approved by: adrian (mentor)
Sponsored by: Smartcom - Bulgaria AD
Differential Revision: https://reviews.freebsd.org/D6395
This is an import of the reworked LEDE dts files. Besides other things
they make it easier for us to reuse.
The only diffs left are for the following SoCs:
MT7620A (fbsd-mt7620a.dtsi)
MT7621 (fbsd-mt7621.dtsi)
MT7628 (fbsd-mt7628an.dtsi)
RT3883 (fbsd-rt3883.dtsi)
So we include the fbsd-*.dtsi files at the end of the original LEDE dtsi
files, using '#include "fbsd-xxxx.dtsi"'.
For example, for MT7621, the LEDE dtsi file is mt7621.dtsi. At the end of
it we add:
#include "fbsd-mt7621.dtsi"
Approved by: adrian (mentor)
Obtained from: LEDE project
Sponsored by: Smartcom - Bulgaria AD
Differential Revision: https://reviews.freebsd.org/D6394
The A83T thermal sensor controller has three sensors. Sensor 0 corresponds
to CPU cluster 0, sensor 1 to CPU cluster 1, and sensor 2 to the GPU. This
driver exports the temperature sensor readings via sysctl.
Calibration data is obtained from SRAM found in the Secure ID module.
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D6378
FDT overlays is de-facto standard for describing expansion boards like
Beaglebone capes or Raspberry Pi shields. The ides is to have basic
DTB for base board and overlays DTB for shields/capes and to construct
final DTB either using human-readable configuration or some
self-discovery mechanism. I believe this approach can also be expanded
to support dynamically loadable FPGA bitstreams on systems like
Zedboard/Zybo.
Overlaying process is simmilar to executable link process for
binaries: each DTB has "exported" symbols and "undefined" symbols, the
latter are resolved using information for the former obtained from
base DTB or one of the overlays applied earlier (more rare case).
This symbols information is not generated by standard dtc that FreeBSD
has in base system, patched[1] version required to produces
overlay-compatible blobs. So although DTB files generated by
buildkernel do not support overlays there are enough
vendor/community-provided DTB blobs ciruclating around to justify
committing this change to ubldr.
This commit introduces handler for "fdt_overlays" variable that can be
defined either as a loader env variable or U-Boot env variable.
fdt_overlays is comma-separated list of .dtbo files located in
/boot/dtb/ directory along with base .dtb. ubldr loads files and
applies them one-by-one to base .dtb and then passes result blob to
the kernel.
[1] dd6a0533e8
Differential Revision: https://reviews.freebsd.org/D3180
- Factor out common part to zynq-7000.dtsi
- Fix problem with Zynq interrupts by using interrupt "triples"
in .dtsi file to differentiate between edge-triggered and
level-triggered interrupts
- cgem driver now recognizes "status" property
Submitted by: Thomas Skibo <thomasskibo@yahoo.com>
Differential Revision: https://reviews.freebsd.org/D6095
The introduction of palmbus and previous work allows us to cut the
differences between FreeBSD and OpenWRT DTS files a bit further.
Approved by: adrian (mentor)
Sponsored by: Smartcom - Bulgaria AD
Differential Revision: https://reviews.freebsd.org/D6043
This change is required so that RT3662/RT3883 PCI can function correctly
Approved by: adrian (mentor)
Sponsored by: Smartcom - Bulgaria AD
Differential Revision: https://reviews.freebsd.org/D6028
This revision suggests dtsi patches to be used with the original OpenWRT
dtsi files so we can re-use what has already been done in OpenWRT for the
Mediatek/Ralink SoCs.
The only thing that is required after importing this revision should be
the following:
1. Import OpenWRT dts/dtsi files into sys/gnu/dts/mips
2. Run the following script in sys/gnu/dts/mips:
for f in `ls [mr]t*.dtsi`; do
printf "\n#include <fbsd-$f>\n" > $f
done
This will apply our dtsi patches to OpenWRT's dtsi files and will allow us
to re-use dts/dtsi files for ~170 Mediatek/Ralink boards.
Currently our drivers are not 100% compatible with OpenWRT's dts files, but
they're compatible enough.
We can add more functionality in the future that would better leverage the
OpenWRT work as well.
Approved by: adrian (mentor)
Sponsored by: Smartcom - Bulgaria AD
Differential Revision: https://reviews.freebsd.org/D5965
a child of it. This is done in conformity with Linux dts files and
as preparation for rework of BCM2836 interrupt controller for INTRNG.
Reviewed by: gonzo
Differential Revision: https://reviews.freebsd.org/D5807
The following pheripherals are supported: UART, MMC, AHCI, EHCI, PCIe, I2C,
PMIC, GPIO, CPU temperature and clock.
Note: The PCIe driver is pure mash at this moment. It will be reworked
immediately when both D5237 and D2579 enter the current tree.
After ARM_INTRNG introduction, MPIC code needed several modifications:
- IRQ resource and its handler added
- several DEVMETHODs of INTRNG interface implemented
- defines enhanced to ensure code compiles as well for AXP as for A38X
- added dummy MSI_IRQ, ERR_IRQ defines for Armada38x
- MPIC driver was added to files.armada38x, ARM_INTRNG option enabled in
kernconf file and regs of MPIC corrected in dts file.
Instead of modifying Armada38X DTS, offsets to CPU registers defined in
driver were changed. That required restoring 'reg' property of mpic node
in ArmadaXP to state compliant with Linux DTS.
Additionally, required ARM_INTRNG definitions were added to mv_common.c.
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: adrian, andrew, ian, skra
Approved by: cognet (mentor)
Differential Revision: https://reviews.freebsd.org/D5030
ubldr.
The changes are mostly dealing with removing unnecessary casts from the U-Boot
API (we're passing only pointers, no obvious reason to cast them to uint32_t),
cleaning up some compiler warnings and using the proper printf format
specifiers in order to be able to compile cleanly for both 32-bit and 64-bit
MIPS targets.
Reviewed by: imp
Approved by: adrian (mentor)
Sponsored by: Smartcom - Bulgaria AD
Differential Revision: https://reviews.freebsd.org/D5312
sys/boot/fdt/Makefile
sys/boot/uboot/fdt/Makefile
sys/boot/uboot/lib/Makefile
This causes compilation issues on MIPS due to trying to link PIC with non-PIC
code. This revision includes bsd.stand.mk in the above files.
Reviewed by: imp
Approved by: adrian (mentor)
Sponsored by: Smartcom - Bulgaria AD
Differential Revision: https://reviews.freebsd.org/D5311
The HDMI driver will attach a framebuffer device when a display is
connected. If the EDID can be read and contains a preferred mode, it
will be used. Otherwise the framebuffer will default to 800x600.
In addition, if the EDID contains a CEA-861 extension block and the
"basic audio" flag is set, audio playback at 48kHz 16-bit stereo is
enabled on the controller.
Reviewed by: andrew
Approved by: gonzo (mentor)
Differential Revision: https://reviews.freebsd.org/D5383
Tested on Spike simulator with 2 and 16 cores (tlb enabled),
so set MAXCPU to 16 at this time.
This uses FDT data to get information about CPUs
(code based on arm64 mp_machdep).
Invalidate entire TLB cache as it is the only way yet.
Sponsored by: DARPA, AFRL
Sponsored by: HEIF5
configuration from the FDT data, then set the pins into the requested
state. As part of this the gpio controller now reports the correct number
of pins instead of returning the number of bank * 32.
To allow for a future consolidated kernel we add the SOC_ALLWINNER_A10 and
SOC_ALLWINNER_A20 kernel options. These need to be set as appropriate for
the SoC the kernel will boot on.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Differential Revision: https://reviews.freebsd.org/D5177
A10/A20 SoC. Based loosely on the submitters NetBSD driver, tested on
Cubieboard 2. Playback and capture are supported.
Submitted by: Jared McNeill <jmcneill@invisible.ca>
Differential Revision: https://reviews.freebsd.org/D5202
dts files. It may be removed once it will be fixed upstream.
This is done just to supresses a warning during dtb evaluation as
there is no elm driver in tree at present.
least the audio codec driver currently in review.
Submitted by: Jared McNeill <jmcneill@invisible.ca>
Differential Revision: https://reviews.freebsd.org/D5050
o Add kernel configuration for QEMU.
Both SPIKE and QEMU kernel configs are temporary (until
we will be able to obtain DTB from loader).
Sponsored by: DARPA, AFRL
Sponsored by: HEIF5
* Use the Linux compat string
* Use EARLY_DRIVER_MODULE to attach at the right time
* Add a generic A10 kernel config file
* A20 now use generic_timer
* Add two new dts files for Olimex boards
* Update our custom DTS file for A10 and A20 to use the same compatible
property names as the vendor ones.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Differential Revision: https://reviews.freebsd.org/D4792
This is the final step required allowing to compile and to run RISC-V
kernel and userland from HEAD.
RISC-V is a completely open ISA that is freely available to academia
and industry.
Thanks to all the people involved! Special thanks to Andrew Turner,
David Chisnall, Ed Maste, Konstantin Belousov, John Baldwin and
Arun Thomas for their help.
Thanks to Robert Watson for organizing this project.
This project sponsored by UK Higher Education Innovation Fund (HEIF5) and
DARPA CTSRD project at the University of Cambridge Computer Laboratory.
FreeBSD/RISC-V project home: https://wiki.freebsd.org/riscv
Reviewed by: andrew, emaste, kib
Relnotes: Yes
Sponsored by: DARPA, AFRL
Sponsored by: HEIF5
Differential Revision: https://reviews.freebsd.org/D4982
Invalid (in FreeBSD) definition of PCI controller was
replaced with another one, working in FreeBSD environment.
PCI controller's entry had to move from its parent node
so as to be recognized properly by FBSD.
PCI was enabled in kernel configuration file.
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4379
uart_dev_ns8250 now relies on compatible property instead of additional
'busy-detect' cell. All drivers with compatible = "snps,dw-apb-uart" have
busy detection turned on. DTS files of devices affected by the change
were modified and 'busy-detect' property was removed.
Reviewed by: andrew, ian, imp
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4218
Ranges property of 'soc' node used two-cell addresses which resulted in
casting errors as simplebus resource allocation works with 32-bit u_long
variables. FDT ranges were simplified.
Reviewed by: imp
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Michal Stanek <mst@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4212
This commit introduces initial support for Marvell Armada38x platform.
Changes:
- Add common DTS files for Armada38x SoCs and DTS file for A388-GP
- Add ARMADA38X kernel configuration
- Add option SOC_MV_ARMADA38X and set MV_PCI_PORTS
- Add list of files to compile
- Implement get_tclk(), get_sar_value(), cpu_reset() functions
- Add CPU ID and SoC numbers
- Correct ifdefs in arm/mv/timer.c
Reviewed by: ian, imp
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Michal Stanek <mst@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4210
This is not properly respecting WITHOUT or ARCH dependencies in target/.
Doing so requires a massive effort to rework targets/ to do so. A
better approach will be to either include the SUBDIR Makefiles directly
and map to DIRDEPS or just dynamically lookup the SUBDIR. These lose
the benefit of having a userland/lib, userland/libexec, etc, though and
results in a massive package. The current implementation of targets/ is
very unmaintainable.
Currently rescue/rescue and sys/modules are still not connected.
Sponsored by: EMC / Isilon Storage Division
Zybo needs its own DTB and has a different PHY, so add it to
the base kernel. Details on building bootable SD images at
http://www.thomasskibo.com/zedbsd/
Submitted By: Thomas Skibo
so they were disabled during DTS transition. Though there are
no standard devices/drivers on them people might use iic(4) userland
interface to access these buses.
The Allwinner SoC has an AHCI device on its internal main bus rather
than the PCI bus. This SoC is somewhat underdocumented, and its SATA
controller is no exception. The methods to support this chip were
harvested from the Linux Allwinner SDK, and then constants invented to
describe what's going on based on low-level constants contained in the
SATA standard and guess work.
This SoC requires a specific AHCI channel setup in order to start the
operations on the channel properly.
Clock setup and AHCI channel setup idea came from NetBSD.
Tested on Cubieboard 2 and Banana pi (and attachment on Cubieboard by
Pratik Singhal).
Differential Revision: https://reviews.freebsd.org/D737
Submitted by: imp
Reviewed by: imp, ganbold, mav, andrew
- Add driver for TDA19988 HDMI framer
- Add simple interface to communicate with HDMI sink: read EDID and set videomode
- Add event-based API to notify LCD controller when HDMI sink is available
- Add HDMI framer node and add refernce to it to lcdc node. This part of
DTS tree is custom and does not match Linux DTS because Linux uses
combination of pseudo-node in DTS and hardcoded driver information
that does not map to our model.
based device.
Following u-boot commands allow FreeBSD boot on
Yiyate Android TV Box (aml8726-m3):
tv open 480p
mmc rescan 0
fatload mmc 0 0x80100000 kernel.bin
go 0x80100000
The current FreeBSD driver doesn't program the video
clocks so the u-boot tv command is necessary in order
for the frame buffer to be useful (otherwise it can
be skipped).
The SD card for the Yiyate Android TV Box doesn't need
anything special beyond creating a FAT16 and a UFS
filesystem.
Differential Revision: https://reviews.freebsd.org/D2636
Submitted by: John Wehle
files to vendor-provided ones. It should make easier to adopt platform
code to new revisions of hardware and to use DTS overlays for various
Beaglebone extensions (shields/capes).
Original dts filenames were not changed, they're now wrappers over dts
files provided by TI. So make sure you update .dtb files on your
devices as part of kernel update
GPIO addressing was changed: instead of one global /dev/gpioc0 there
are per-bank instances of /dev/gpiocX. Each bank has 32 pins so for
instance pin 121 on /dev/gpioc0 in old addressing scheme is now pin 25
on /dev/gpioc3
On Pandaboard serial console devices was changed from /dev/ttyu0 to
/dev/ttyu2 so you'll have to update /etc/ttys to get login prompt
on serial port in multiuser mode. Single user mode serial console
should work as-is
Differential Revision: https://reviews.freebsd.org/D2146
Reviewed by: rpaulo, ian, Michal Meloun, Svatopluk Kraus
This is based on the patch sent by Alexander Fedorov with the following
fixes/improvements:
- Better error handling;
- Clock is derived from PLL6 (obtained from netbsd);
- No more unnecessary busy loops on interrupt handler;
- style(9) fixes and code cleanup.
I also want to thanks Martin Galvan who has sent an alternative
implementation with some interesting fixes.
Tested on CubieBoard2, Banana-Pi (thanks to netgate!) and Cubieboard1
(Pratik Singhal).
This is intended to pave the way for the upcoming GSoC work (and make
easier the build of images for the supported boards).
PR: 196081
Submitted by: Alexander Fedorov <alexander.fedorov@rtlservice.com>
determined at runtime so there's no need to set the values in
each DTS.
Tested on YYHD18 (aml8726-m3), VSATV102 (aml8726-m6), and
ODROIDC1 (aml8726-m8b).
Differential Revision: https://reviews.freebsd.org/D2588
Submitted by: John Wehle
The Alpine Platform-On-Chip offers multicore processing
(quad ARM Cortex-A15), 1/10Gb Ethernet, SATA 3, PCI-E 3,
DMA engines, Virtualization, Advanced Power Management and other.
This code drop involves basic platform support including:
SMP, IRQs, SerDes, SATA. As of now it is missing the PCIe support.
Part of the functionality is provided by the low-level code (HAL)
delivered by the chip vendor (Annapurna Labs) and is a subject to
change in the future (is planned to be moved to sys/contrib directory).
The review log for this commit is available here:
https://reviews.freebsd.org/D2340
Reviewed by: andrew, ian, imp
Obtained from: Semihalf
Sponsored by: Annapurna Labs
The 'pwr' LED is connected to GPIO pin 35 (active high) and the 'act' LED
is connected to GPIO pin 47 (active high).
Remove the GPIO pin 47 from reserved pins list, previously it was used to
signaling the SD Card presence and now it is used by act LED.
contains one. Published dts source often includes a minimal default
memory definition and expects it to be overridden by the bootloader after
determining the actual physical memory in the system.
o Digital Audio Multiplexer (AUDMUX)
o Smart Direct Memory Access Controller (SDMA)
o Synchronous Serial Interface (SSI)
Disable by default as it depends on SDMA firmware.
Sponsored by: Machdep, Inc.
driver on Rockchip boards. It currently supports PIO mode
and dma mode needs external dma controller to be used.
Submitted by: jmcneill
Approved by: stas (mentor)
Implement a subset of the multiboot specification in order to boot Xen
and a FreeBSD Dom0 from the FreeBSD bootloader. This multiboot
implementation is tailored to boot Xen and FreeBSD Dom0, and it will
most surely fail to boot any other multiboot compilant kernel.
In order to detect and boot the Xen microkernel, two new file formats
are added to the bootloader, multiboot and multiboot_obj. Multiboot
support must be tested before regular ELF support, since Xen is a
multiboot kernel that also uses ELF. After a multiboot kernel is
detected, all the other loaded kernels/modules are parsed by the
multiboot_obj format.
The layout of the loaded objects in memory is the following; first the
Xen kernel is loaded as a 32bit ELF into memory (Xen will switch to
long mode by itself), after that the FreeBSD kernel is loaded as a RAW
file (Xen will parse and load it using it's internal ELF loader), and
finally the metadata and the modules are loaded using the native
FreeBSD way. After everything is loaded we jump into Xen's entry point
using a small trampoline. The order of the multiboot modules passed to
Xen is the following, the first module is the RAW FreeBSD kernel, and
the second module is the metadata and the FreeBSD modules.
Since Xen will relocate the memory position of the second
multiboot module (the one that contains the metadata and native
FreeBSD modules), we need to stash the original modulep address inside
of the metadata itself in order to recalculate its position once
booted. This also means the metadata must come before the loaded
modules, so after loading the FreeBSD kernel a portion of memory is
reserved in order to place the metadata before booting.
In order to tell the loader to boot Xen and then the FreeBSD kernel the
following has to be added to the /boot/loader.conf file:
xen_cmdline="dom0_mem=1024M dom0_max_vcpus=2 dom0pvh=1 console=com1,vga"
xen_kernel="/boot/xen"
The first argument contains the command line that will be passed to the Xen
kernel, while the second argument is the path to the Xen kernel itself. This
can also be done manually from the loader command line, by for example
typing the following set of commands:
OK unload
OK load /boot/xen dom0_mem=1024M dom0_max_vcpus=2 dom0pvh=1 console=com1,vga
OK load kernel
OK load zfs
OK load if_tap
OK load ...
OK boot
Sponsored by: Citrix Systems R&D
Reviewed by: jhb
Differential Revision: https://reviews.freebsd.org/D517
For the Forth bits:
Submitted by: Julien Grall <julien.grall AT citrix.com>
To cut off the power we need to start the shutdown sequence by writing
the OFF bit on PMIC.
Once the PMIC is programmed the SoC needs to toggle the PMIC_PWR_ENABLE
pin when it is ready for the PMIC to cut off the power. This is done by
triggering the ALARM2 interrupt on SoC RTC.
The RTC driver only works in power management mode which means it won't
provide any kind of time keeping functionality. It only implements a way
to trigger the ALARM2 interrupt when requested.
Differential Revision: https://reviews.freebsd.org/D1489
Reviewed by: rpaulo
MFC after: 2 weeks
This enables the use of GPIO pins as interrupt sources for kernel devices
directly attached to gpiobus (userland notification will be added soon).
The use of gpio interrupts for other kernel devices will be possible when
intrng is complete.
All GPIO pins can be set to trigger on:
- active-low;
- active-high;
- rising edge;
- falling edge.
Tested on: Beaglebone-black
o Move similar block/networking methods to common file
o Follow r275640 and correct MMIO registers width
o Pass value to MMIO platform_note method.
Sponsored by: DARPA, AFRL
