The calibrate callout is done with the sc lock held.
This only showed up when using an older NIC (AR5212) whose
radio/phy requires the rfgain adjustment.
Pointy-hat-to: adrian
Sponsored by: Hobnob, Inc.
* Failall is now named just that.
* Add TX ok and TX fail, for aggregate frame sub-frames.
This will break athstats; a followup commit wil resolve this.
Sponsored by: Hobnob, Inc.
Because there is no reliable way to know whether RX MAC is in
stopped state, rejecting all frames would be the only way to
minimize possible races.
Otherwise it's possible to receive frames while stop command
execution is in progress and controller can DMA the frame to freed
RX buffer during that period.
This was observed on recent PCIe controllers(i.e. RTL8111F).
While this change may not be required on old controllers it
wouldn't make negative effects on old controllers. One side effect
of this change is disabling receive so driver reprograms RL_RXCFG
to receive WOL frames when it is put into suspend or shutdown.
This should address occasional 'memory modified free' errors seen
on recent RealTek controllers.
driver would ignore the first link state update if controller
already established a link such that it would have to take
additional link state handling in re_tick().
access.
While I'm here, enable WOL through magic packet but disable waking
up system via unicast, multicast and broadcast frames. Otherwise,
multicast or unicast frame(e.g. ICMP echo request) can wake up
system which is not probably wanted behavior on most environments.
This was not known as problem because RL_CFG5 register access had
not effect until this change.
The capability to wake up system with unicast/multicast frames
are still set in driver, default off, so users who need that
feature can still activate it with ifconfig(8).
one. Interestingly, these are actually the default for quite some time
(bus_generic_driver_added(9) since r52045 and bus_generic_print_child(9)
since r52045) but even recently added device drivers do this unnecessarily.
Discussed with: jhb, marcel
- While at it, use DEVMETHOD_END.
Discussed with: jhb
- Also while at it, use __FBSDID.
bit should not affect link establishment process of auto-negotiation
if manual configuration is not used, which is true in auto-negotiation.
However it seems setting this bit interfere with IP1001 PHY's
down-shifting feature such that establishing a 10/100Mbps link failed
when 1000baseT link is not available during auto-negotiation process.
Tested by: Andrey Smagin <samspeed <> mail dot ru >
Pause timer value is initialized to 0xFFFF. Controller allows just
4 different TX pause thresholds. The lowest possible threshold
value looks too aggressive so use next available threshold value.
- Remove MIIBUS statchg callback and program VGE_DIAGCTL before
initiating link establishment. Previously driver used to
program VGE_DIAGCTL after getting a link in statchg callback.
It seems the VGE_DIAGCTL register works like a kind of MII
register such that it requires setting a 'to be' mode in advance
rather than relying on resolved speed/duplex of established link.
This means the statchg callback is not needed in driver. In
addition, if there was no link at the time of media change, this
was not called at all.
- Introduce vge_ifmedia_upd_locked() to change current media to
configured one. Actual media change is performed only after PHY
reset and VGE_DIAGCTL setup.
- In WOL configuration, make sure to clear forced mode such that
controller can rely on auto-negotiation.
- Unlike most other drivers that use miibus(4), vge(4) used
controller's auto-polling feature for link state tracking via
interrupt. This came from controller's inefficient mechanism to
access MII registers. On link state change interrupt, vge(4)
used to get current link state with series of MII register
accesses. Because vge(4) already enabled auto polling, read PHY
status register to resolved speed/duplex/flow control parameters.
vge(4) still does not drive MII_TICK to reduce number of MII
register accesses which in turn means the driver does not know the
status of auto-negotiation. This was a one of long standing
issue of vge(4). Probably driver may be able to implement a timer
that keeps track of auto-negotiation state and restart
auto-negotiation when driver couldn't establish a link within a
specified period. However the controller does not provide a
reliable way to detect auto-negotiation failure so I'm not sure
whether it's worth to implement it in driver.
Alternatively driver can completely disable MII auto-polling and
let miibus(4) poll link state by driving MII_TICK. This may reduce
unnecessary overhead of stopping/restarting MII auto-polling of
controller. Unfortunately it was known that some variants of
controller does not work correctly if MII auto-polling is disabled.
This fixes panics that users have been seeing when operating in station mode,
where the interface undergoes a lot more resets then in hostap mode (ie whilst
doing channel scanning.)
Reported by: arundel, wblock@wonkity.com
Sponsored by: Hobnob, Inc.
passed over to the runtime firmware on 6050 devices. Instead let
the runtime firmware do the calibration itself. This fixes support
for the 6050 series devices.
Obtained from: OpenBSD
Submitted by: kevlo
Tested by: lx, Tz-Huan Huang(earlier version)
defined and will allow consumers, willing to provide options, file and
line to locking requests, to not worry about options redefining the
interfaces.
This is typically useful when there is the need to build another
locking interface on top of the mutex one.
The introduced functions that consumers can use are:
- mtx_lock_flags_
- mtx_unlock_flags_
- mtx_lock_spin_flags_
- mtx_unlock_spin_flags_
- mtx_assert_
- thread_lock_flags_
Spare notes:
- Likely we can get rid of all the 'INVARIANTS' specification in the
ppbus code by using the same macro as done in this patch (but this is
left to the ppbus maintainer)
- all the other locking interfaces may require a similar cleanup, where
the most notable case is sx which will allow a further cleanup of
vm_map locking facilities
- The patch should be fully compatible with older branches, thus a MFC
is previewed (infact it uses all the underlying mechanisms already
present).
Comments review by: eadler, Ben Kaduk
Discussed with: kib, jhb
MFC after: 1 month
mode configuration registers. This is apparently required for correct
behaviour, but also requires the chip to actually officially support it.
Sponsored by: Hobnob, Inc.
"correct" handling of frames in the RX pending queue during interface
transitions.
* ath_stoprecv() doesn't blank out the descriptor list - that's what
ath_startrecv() does. So, change a comment to reflect that.
* ath_stoprecv() does include a large (3ms) delay to let pending DMA
complete. However, I'm under the impression that the stopdma hal
method does check for a bit in the PCU to indicate DMA has stopped.
So, to help with fast abort and restart, modify ath_stoprecv() to take
a flag which indicates whether this is needed.
* Modify the uses of ath_stoprecv() to pass in a flag to support the
existing behaviour (ie, do the delay.)
* Remove some duplicate PCU teardown code (which wasn't shutting down DMA,
so it wasn't entirely correct..) and replace it with a call to
ath_stoprecv(sc, 0) - which disables the DELAY call.
The upshoot of this is now channel change doesn't simply drop completed
frames on the floor, but instead it cleanly handles those frames.
It still discards pending TX frames in the software and hardware queues
as there's no (current) logic which forcibly recalculates the rate control
information (or whether they're appropriate to be on the TX queue after
a channel change), that'll come later.
This still doesn't stop all the sources of queue stalls but it does
tidy up some of the code duplication.
To be complete, queue stalls now occur during normal behaviour -
they only occur after some kind of broken behaviour causes an interface
or node flush, upsetting the TX/RX BAW. Subsequent commits will
incrementally fix these and other related issues.
Sponsored by: Hobnob, Inc.
to the kernel's pause() function. The pause() function can now be used
when cold != 0. Also assert that the timeout in system ticks must be
positive.
Suggested by: Bruce Evans
MFC after: 1 week
to kern/subr_bus.c. Simplify this function so that it no longer
depends on malloc() to execute. Identify a few other places where
it makes sense to use device_delete_all_children().
MFC after: 1 week
It's not currently used; it didn't build on 32-bit and the previous build fix
is incorrect. If we really implement self-tests we can do this again
properly.
Submitted by: Ben Hutchings <bwh -at- solarflare.com>
MFC after: 3 weeks
This field is supposed to be set to the interface bit rate, but for some
reason I thought it was denominated in kilobits. Multiply the values up
accordingly, taking care to saturate rather than overflow on 32-bit
architectures.
Submitted by: Ben Hutchings <bwh -at- solarflare.com>
MFC after: 3 weeks
addresses from being probed and attaching something including ukphy(4)
to it. This is mainly necessarily for PHY switches that create duplicate
or fake PHYs on the bus that can corrupt the PHY state when accessed or
simply cause problems when ukphy(4) isolates the additional instances.
- Change miibus(4) to be a hinted bus, allowing to add child devices via
hints and to set their attach arguments (including for automatically
probed PHYs). This is mainly needed for PHY switches that violate IEEE
802.3 and don't even implement the basic register set so we can't probe
them automatically. However, the ability to alter the attach arguments
for automatically probed PHYs is also useful as for example it allows
to test (or tell a user to test) new variant of a PHY with a specific
driver by letting an existing driver attach to it via manipulating the
IDs without the need to touch the source code or to limit a Gigabit
Ethernet PHY to only announce up to Fast Ethernet in order to save
energy by limiting the capability mask. Generally, a driver has to
be hinted via hint.phydrv.X.at="miibusY" and hint.phydrv.X.phyno="Z"
(which already is sufficient to add phydrvX at miibusY at PHY address
Z). Then optionally the following attach arguments additionally can
be configured:
hint.phydrv.X.id1
hint.phydrv.X.id2
hint.phydrv.X.capmask
- Some minor cleanup.
Reviewed by: adrian, ray
dcphy(4) (CID 9283).
- In dc_detach(), check whether ifp is NULL as dc_attach() may call the
former without ifp being allocated (CID 4288).
Found with: Coverity Prevent(tm)
!DC_IS_ADMTEK in dc_miibus_statchg(). This change broke link
establishment of Intel 21143 with dcphy(4) where it stuck in
"ability detect" state without completing auto-negotiation.
Also nuke dc_if_media as it's not actually used.
Submitted by: marius
Tested on Qemu/KVM, VirtualBox, and BHyVe.
Currently built as modules-only on i386/amd64. Man pages not yet hooked
up, pending review.
Submitted by: Bryan Venteicher bryanv at daemoninthecloset dot org
Reviewed by: bz
MFC after: 4 weeks or so
for the ath(4) driver.
Currently, there's nothing stopping reset, channel change and general
TX/RX from overlapping with each other. This wasn't a big deal with
pre-11n traffic as it just results in some dropped frames.
It's possible this may have also caused some inconsistencies and
badly-setup hardware.
Since locks can't be held across all of this (the Linux solution)
due to LORs with the network stack locks, some state counter
variables are used to track what parts of the code the driver is
currently in.
When the hardware is being reset, it disables the taskqueue and
waits for pending interrupts, tx, rx and tx completion before
it begins the reset or channel change.
TX and RX both abort if called during an active reset or channel
change.
Finally, the reset path now doesn't flush frames if ATH_RESET_NOLOSS
is set. Instead, completed TX and RX frames are passed back up to
net80211 before the reset occurs.
This is not without problems:
* Raw frame xmit are just dropped, rather than placed on a queue.
The net80211 stack should be the one which queues these frames
rather than the driver.
* It's all very messy. It'd be better if these hardware operations
were serialised on some kind of work queue, rather than hoping
they can be run in parallel.
* The taskqueue block/unblock may occur in parallel with the
newstate() function - which shuts down the taskqueue and restarts
it once the new state is known. It's likely these operations should
be refcounted so the taskqueue is restored once no other areas
in the code wish to suspend operations.
* .. interrupt disable/enable should likely be refcounted as well.
With this work, the driver does not drop frames during stuck beacon
or fatal errors and thus 11n traffic continues to run correctly.
Default and full resets however do still drop frames and it's possible
this may occur, causing traffic loss and session stalls.
Sponsored by: Hobnob, Inc.
completely skipping them, create ahcich devices for them to allocate unit
numbers, but mark them as disabled to prevent driver probe and attach.
Last time some BIOSes tend to report unused channels as "not implemented".
This change makes ahcichX devices numbering consistent, independently of
connected disks. It makes per-channel driver hints usable and CAM devices
wiring possible on such systems.
I/O from userspace, capable of line rate at 10G, see
http://info.iet.unipi.it/~luigi/netmap/
At this time I am bringing in only the generic code (sys/dev/netmap/
plus two headers under sys/net/), and some sample applications in
tools/tools/netmap. There is also a manpage in share/man/man4 [1]
In order to make use of the framework you need to build a kernel
with "device netmap", and patch individual drivers with the code
that you can find in
sys/dev/netmap/head.diff
The file will go away as the relevant pieces are committed to
the various device drivers, which should happen in a few days
after talking to the driver maintainers.
Netmap support is available at the moment for Intel 10G and 1G
cards (ixgbe, em/lem/igb), and for the Realtek 1G card ("re").
I have partial patches for "bge" and am starting to work on "cxgbe".
Hopefully changes are trivial enough so interested third parties
can submit their patches. Interested people can contact me
for advice on how to add netmap support to specific devices.
CREDITS:
Netmap has been developed by Luigi Rizzo and other collaborators
at the Universita` di Pisa, and supported by EU project CHANGE
(http://www.change-project.eu/)
The code is distributed under a BSD Copyright.
[1] In my opinion is a bad idea to have all manpage in one directory.
We should place kernel documentation in the same dir that contains
the code, which would make it much simpler to keep doc and code
in sync, reduce the clutter in share/man/ and incidentally is
the policy used for all of userspace code.
Makefiles and doc tools can be trivially adjusted to find the
manpages in the relevant subdirs.
