Change several int variables to size_t, ssize_t, or ptrdiff_t.
This should fix the bug described in CVE-2012-5667 when an input
line is so long that its length cannot be stored in an int
variable.
This is based on NetBSD's revision which says:
This change to NetBSD's version of GNU grep 2.5.1 (licenced under
GPLv2) was made without direct reference to any code licenced
under GPLv3.
Obtained from: NetBSD
MFC after: 3 days
dt_cg_ptrsize() and generally cleans up some of the error handling around
register allocation.
This change corresponds to part of illumos-gate commit e5803b76927480:
3025 register leak in D code generation
Reviewed by: pfg
Obtained from: illumos
MFC after: 1 month
I added this block, knowing that lint does not support _Thread_local.
When linting, we could argue that we don't care about TLS (yet). It
seems, however, that external pieces of software also sometimes do a
-Dlint, regex the output and compile it again.
Reported by: swills
apply to most jails but do apply to vnet jails. This includes adding
a new sysctl "security.jail.vnet" to identify vnet jails.
PR: conf/149050
Submitted by: mdodd
MFC after: 3 days
Group onboard mic and headphone mic jack together. Creates association that
will switch between microphone inputs depending on the state of the headphone
jack being connected to a live mic.
Fixes onboard mic not working at all on T520.
Tested on T520, T420.
Suspect X220 needs this too, untested on.
MFC after: 1 month
The list-based DMA engine has the following behaviour:
* When the DMA engine is in the init state, you can write the first
descriptor address to the QCU TxDP register and it will work.
* Then when it hits the end of the list (ie, it either hits a NULL
link pointer, OR it hits a descriptor with VEOL set) the QCU
stops, and the TxDP points to the last descriptor that was transmitted.
* Then when you want to transmit a new frame, you can then either:
+ write the head of the new list into TxDP, or
+ you write the head of the new list into the link pointer of the
last completed descriptor (ie, where TxDP points), then kick
TxE to restart transmission on that QCU>
* The hardware then will re-read the descriptor to pick up the link
pointer and then jump to that.
Now, the quirks:
* If you write a TxDP when there's been no previous TxDP (ie, it's 0),
it works.
* If you write a TxDP in any other instance, the TxDP write may actually
fail. Thus, when you start transmission, it will re-read the last
transmitted descriptor to get the link pointer, NOT just start a new
transmission.
So the correct thing to do here is:
* ALWAYS use the holding descriptor (ie, the last transmitted descriptor
that we've kept safe) and use the link pointer in _THAT_ to transmit
the next frame.
* NEVER write to the TxDP after you've done the initial write.
* .. also, don't do this whilst you're also resetting the NIC.
With this in mind, the following patch does basically the above.
* Since this encapsulates Sam's issues with the QCU behaviour w/ TDMA,
kill the TDMA special case and replace it with the above.
* Add a new TXQ flag - PUTRUNNING - which indicates that we've started
DMA.
* Clear that flag when DMA has been shutdown.
* Ensure that we're not restarting DMA with PUTRUNNING enabled.
* Fix the link pointer logic during TXQ drain - we should always ensure
the link pointer does point to something if there's a list of frames.
Having it be NULL as an indication that DMA has finished or during
a reset causes trouble.
Now, given all of this, i want to nuke axq_link from orbit. There's now HAL
methods to get and set the link pointer of a descriptor, so what we
should do instead is to update the right link pointer.
* If there's a holding descriptor and an empty TXQ list, set the
link pointer of said holding descriptor to the new frame.
* If there's a non-empty TXQ list, set the link pointer of the
last descriptor in the list to the new frame.
* Nuke axq_link from orbit.
Note:
* The AR9380 doesn't need this. FIFO TX writes are atomic. As long as
we don't append to a list of frames that we've already passed to the
hardware, all of the above doesn't apply. The holding descriptor stuff
is still needed to ensure the hardware can re-read a completed
descriptor to move onto the next one, but we restart DMA by pushing in
a new FIFO entry into the TX QCU. That doesn't require any real
gymnastics.
Tested:
* AR5210, AR5211, AR5212, AR5416, AR9380 - STA mode.
socket to allow propagation of changes to a Heimdal Kerberos database
from the KDC master to the slave(s) work on IPv6 as well.
Update the stats logging to also handle IPv6 addresses.
Reported by: peter (found on FreeBSD cluster)
X-to-be-tested-by: peter
MFC after: 3 weeks
Most likely some non-USB compliant devices will choke on it
sooner or later. Clear stall is strictly speaking not needed.
If the first MIDI command sent or transmitted is lost, this
is not a big problem for us.
MFC after: 1 week
Set a valid alternate interface setting
when enumerating USB audio devices else
the device mentioned will not work like
expected.
PR: usb/178722
MFC after: 1 week
o The CP2101 and CP2102 do not support GPIO pin use at all, enforce this.
o Support reading the GPIO status on the second port of the CP2105. More
work is needed before the CP2105 GPIO pins can be used as outputs.
Hardware donated by: Silicon Labs
MFC after: 3 weeks
