The BWD NTB device will drop the link if an error is encountered on the
point-to-point PCI bridge. The link will stay down until all errors are
cleared and the link is re-established. On link down, check to see if
the error is detected, if so do the necessary housekeeping to try and
recover from the error and reestablish the link.
There is a potential race between the 2 NTB devices recovering at the
same time. If the times are synchronized, the link will not recover and
the driver will be stuck in this loop forever. Add a random interval to
the recovery time to prevent this race.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
checked with dumpfs(8). This may lead to other problems, f.e. geom_label kernel
module sanity checks do not like zero fs_old_size value and skips such UFS1
file system while tasting (fs_old_size derives from sblock.fs_providersize).
PR: 203704
Submitted by: eugen@grosbein.net
Reviewed by: marcel
[x86] Fix wrong lowering of vsetcc nodes (PR25080).
Function LowerVSETCC (in X86ISelLowering.cpp) worked under the wrong
assumption that for non-AVX512 targets, the source type and destination type
of a type-legalized setcc node were always the same type.
This assumption was unfortunately incorrect; the type legalizer is not always
able to promote the return type of a setcc to the same type as the first
operand of a setcc.
In the case of a vsetcc node, the legalizer firstly checks if the first input
operand has a legal type. If so, then it promotes the return type of the vsetcc
to that same type. Otherwise, the return type is promoted to the 'next legal
type', which, for vectors of MVT::i1 is always a 128-bit integer vector type.
Example (-mattr=+avx):
%0 = trunc <8 x i32> %a to <8 x i23>
%1 = icmp eq <8 x i23> %0, zeroinitializer
The initial selection dag for the code above is:
v8i1 = setcc t5, t7, seteq:ch
t5: v8i23 = truncate t2
t2: v8i32,ch = CopyFromReg t0, Register:v8i32 %vreg1
t7: v8i32 = build_vector of all zeroes.
The type legalizer would firstly check if 't5' has a legal type. If so, then it
would reuse that same type to promote the return type of the setcc node.
Unfortunately 't5' is of illegal type v8i23, and therefore it cannot be used to
promote the return type of the setcc node. Consequently, the setcc return type
is promoted to v8i16. Later on, 't5' is promoted to v8i32 thus leading to the
following dag node:
v8i16 = setcc t32, t25, seteq:ch
where t32 and t25 are now values of type v8i32.
Before this patch, function LowerVSETCC would have wrongly expanded the setcc
to a single X86ISD::PCMPEQ. Surprisingly, ISel was still able to match an
instruction. In our case, ISel would have matched a VPCMPEQWrr:
t37: v8i16 = X86ISD::VPCMPEQWrr t36, t25
However, t36 and t25 are both VR256, while the result type is instead of class
VR128. This inconsistency ended up causing the insertion of COPY instructions
like this:
%vreg7<def> = COPY %vreg3; VR128:%vreg7 VR256:%vreg3
Which is an invalid full copy (not a sub register copy).
Eventually, the backend would have hit an UNREACHABLE "Cannot emit physreg copy
instruction" in the attempt to expand the malformed pseudo COPY instructions.
This patch fixes the problem adding the missing logic in LowerVSETCC to handle
the corner case of a setcc with 128-bit return type and 256-bit operand type.
This problem was originally reported by Dimitry as PR25080. It has been latent
for a very long time. I have added the minimal reproducible from that bugzilla
as test setcc-lowering.ll.
Differential Revision: http://reviews.llvm.org/D13660
This should fix the "Cannot emit physreg copy instruction" errors when
compiling contrib/wpa/src/common/ieee802_11_common.c, and CPUTYPE is set
to a CPU supporting AVX (e.g. sandybridge, ivybridge).
There is a Xeon hardware errata related to writes to SDOORBELL or B2BDOORBELL
in conjunction with inbound access to NTB MMIO Space, which may hang the
system. To workaround this issue, use one of the memory windows to access the
interrupt and scratch pad registers on the remote system. This bypasses the
issue, but removes one of the memory windows from use by the transport. This
reduction of MWs necessitates adding some logic to determine the number of
available MWs.
Since some NTB usage methodologies may have unidirectional traffic, the ability
to disable the workaround via modparm has been added.
See BF113 in
http://www.intel.com/content/dam/www/public/us/en/documents/specification-updates/xeon-c5500-c3500-spec-update.pdf
See BT119 in
http://www.intel.com/content/dam/www/public/us/en/documents/specification-updates/xeon-e5-family-spec-update.pdf
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
Due to ambiguous documentation, the USD/DSD identification is backward
when compared to the setting in BIOS. Correct the bits to match the
BIOS setting.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
The NTB Xeon hardware has 16 scratch pad registers and 16 back-to-back
scratch pad registers. Correct the #define to represent this and update
the variable names to reflect their usage.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
The current default listen queue for casperd is too small (8) and
hard-coded.
This patch increases the default to SOMAXCONN, and introduces a command
line flag that can used to further increase or decrease the queue length.
PR: bin/202147
Submitted by: <lidl@pix.net>
image up to.
From ticket:
While trying to run FreeBSD/mips on some device having very small flash media,
one is forced to compress file system with mkulzma(8) utility. It is desirable
to specify small UFS block/fragment sizes like 4096/512 bytes for makefs(8)
and big compression block size like 65535 bytes to mkulzma at the same time.
Then one obtains very good comression ratios (like 75% and more) but faces
the following problem.
geom_uncompress kernel module reports GEOM provider size rounded up to its
compression block size. Generally, this changes original media size and now
it fails to match the size of embedded UFS file system that leads to other
problems, f.e. geom_label kernel module does not like this and skips the
file system while tasting the GEOM and looking for UFS label.
This makes it impossible to refer to the file system using known UFS label
instead of something like /dev/map/rootfs.uncompress.
The following patch introduces new command line option "-r roundup" for makefs
that makes it round up the image to specified block size. Hence, geom_uncompress
does not change GEOM media size for images rounded that way and geom_label
accepts such GEOMs just fine.
With the patch applied, one can use following commands:
$ makefs -t ffs -r 65536 -o bsize=4096,fsize=512,label=flash optimization=space fs.img fs
$ mkulzma -s 65536 -o fs.img.ulzma fs.img
PR: bin/203707
Submitted by: <eugen@grosbein.net>
target. This is the feeder for mergemaster / etcupdate. This change
makes installworld/mergemaster/etcupdate behave the same regardless of
whether SENDMAIL_MC or SENDMAIL_CF is used.
If you use a custom SENDMAIL_MC/CF in make.conf and excluded it from
mergemaster.rc/etcupdate.conf to work around the conflicts, you may wish
to revert that or change it from 'ignore' to 'always install'.
If you do not use a custom SENDMAIL_MC/CF, there should be no change in
behavior.
the FreeBSD test suite
functional_test.sh was ported from bin/sh/tests/functional_test.sh, as a
small wrapper around libarchive_test, bsdcpio_test, and bsdtar_test provided
by upstream.
A handful of testcases in lib/libarchive/tests have been disabled as they
were failing when run with kyua test (see BROKEN_TESTS in
lib/libarchive/tests/Makefile)
As a sidenote: this removes the check/test targets from the Makefiles as they
don't match the pattern used in the rest of the FreeBSD test suite.
MFC after: 2 weeks
Sponsored by: EMC / Isilon Storage Division
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Alexander Motin <mav@freebsd.org>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Justin Gibbs <gibbs@scsiguy.com>
Reviewed by: Xin Li <delphij@freebsd.org>
Approved by: Gordon Ross <gordon.ross@nexenta.com>
Author: George Wilson <george.wilson@delphix.com>
illumos/illumos-gate@632802744e
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Simon Klinkert <simon.klinkert@gmail.com>
Reviewed by: Richard Elling <Richard.Elling@RichardElling.com>
Reviewed by: Albert Lee <trisk@omniti.com>
Reviewed by: Xin Li <delphij@freebsd.org>
Approved by: Garrett D'Amore <garrett@damore.org>
Author: George Wilson <george.wilson@delphix.com>
illumos/illumos-gate@139510fb6e
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Albert Lee <trisk@omniti.com>
Reviewed by: Xin Li <delphij@freebsd.org>
Approved by: Garrett D'Amore <garrett@damore.org>
Author: George Wilson <george.wilson@delphix.com>
illumos/illumos-gate@b10bba7246
Formal release notes are available:
https://subversion.apache.org/docs/release-notes/1.9.html
Of particular note, the client checkout format has *not* changed so
upgrades should *not* be required.
When reading a repository (file:// or running as a local server), an
improved fsfs version 7 is available with significant performance
improvements. An optional upgrade is possible to use the new features.
Without the upgrade, this is fully read/write compatible with the
version 6 fsfs as in svn-1.8.
Relnotes: yes
netbsd-tests.test.mk (r289151)
- Eliminate explicit OBJTOP/SRCTOP setting
- Convert all ad hoc NetBSD test integration over to netbsd-tests.test.mk
- Remove unnecessary TESTSDIR setting
- Use SRCTOP where possible for clarity
MFC after: 2 weeks
Sponsored by: EMC / Isilon Storage Divison
This doesn't free the mbuf upon error; the driver ic_raw_xmit method is still
doing that.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3774
Move error handling into ieee80211_parent_xmitpkt() instead of spreading it
between functions.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3772
* Create ieee80211_free_mbuf() which frees a list of mbufs.
* Use it in the fragment transmit path and ath / uath transmit paths.
* Call it in xmit_pkt() if the transmission fails; otherwise fragments
may be leaked.
This should be a big no-op.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3769
This simplifies the code (e.g. allowing use of qsort(3) instead of a
hand-rolled mergesort) and should have better cache properties.
The waste of unused args arrays after resizes is approximately the same as
the savings from getting rid of the next pointers.
At the same time, remove a piece of global state and move some duplicated
code into a function.
When run from bin/ls/tests, for example, the value of TESTSDIR would be
${TESTSBASE}/${RELDIR:H} -> /usr/tests/bin/ls/tests/.. ->
/usr/tests/bin/ls
Document the new behavior in bsd.README.
While here, also document TESTSBASE
Relnotes: yes
Differential Revision: D1022
MFC after: 2 weeks
Sponsored by: EMC / Isilon Storage Division
The system will appear to lockup for long periods of time due to the NTB
driver spending too much time in memcpy. Avoid this by reducing the
number of packets that can be serviced on a given interrupt.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
The ring logic of the NTB receive buffer/transmit memory window requires
there to be at least 2 payload sized allotments. For the minimal size
case, split the buffer into two and set the transport_mtu to the
appropriate size.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
If the NTB link toggles, the driver could stop receiving due to the
tx_index not being set to 0 on the transmitting size on a link-up event.
This is due to the driver expecting the incoming data to start at the
beginning of the receive buffer and not at a random place.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
Each link-up will allocate a new NTB receive buffer when the NTB
properties are negotiated with the remote system. These allocations did
not check for existing buffers and thus did not free them. Now, the
driver will check for an existing buffer and free it if not of the
correct size, before trying to alloc a new one.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
64bit BAR sizes are permissible with an NTB device. To support them
various modifications and clean-ups were required, most significantly
using 2 32bit scratch pad registers for each BAR.
Also, modify the driver to allow more than 2 Memory Windows.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
