of setting it (compiled into vfs_conf.c), but we have a dynamic system
in place. This could probably be better done via a runtime configure
flag in the VFS_SET() VFS declaration, perhaps VFCF_LOCAL, and have the
VFS code propagate this down into MNT_LOCAL at mount time. The other FS's
would need to be updated, havinf UFS and MSDOSFS filesystems without
MNT_LOCAL breaks a few things.. the man page rebuild scans for local
filesystems and currently fails, I suspect that other tools like find
and tar with their "local filesystem only" modes might be affected.
Stick 4 more, twin channel only, instructions behind
.if ( TWIN_CHANNEL)
aic7xxx_asm.c:
Add the -O options which allows the specification of which options
to include in a program listing. This makes it possible to easily
determine the address of any instruction in the program across
different hardware/option configurations. Updated usage() as well.
Cleanup of #ifdef's for LOGIN_CAP.
Fixed bug in empty shell (closes PR#2550).
Refused root logins now displays standard "Login incorrect" and
exhibits identical backoff behaviour to a failed login.
Cleaned up logging of refused logins.
Use #defines for login retries and backoff. Also implemented
definable variables if LOGIN_CAP is defined, with
"login-retries" and "login-backoff" as capabilities
in the default class (closes PR#2805).
TERM from previous environment is no longer truncated.
I broke the cable tuning with my 'TEST_A' code. Remove TEST_A define
till I finish this change for both tuning modes. Note that this
will effectively break the new TVTUNER_SETFREQ/TVTUNER_GETFREQ ioctl()s.
These aren't used by anyone but me yet (attempt to provide full resolution
fine tuning for "fringe" stations) so it should be no problem
written:
1) Full duplex mode is now supported (and works!)
2) The 10Mbps-only PCI Pro/10 should now work (untested, however)
Thanks to Justin Gibbs for providing a PCI bus analyzer trace while the
Intel Windows driver was configuring the board...this made it possible
to figure out the mystery bit that I wasn't setting in the PHY for full
duplex to work.
procs memory page disks faults cpu
r b w avm fre flt re pi po fr sr w0 w1 in sy cs us sy id
1 0 04135184 6016 180 2 1 0 158 135 10 0 386 1820 77 20 6 74
looks like:
procs memory page disks faults cpu
r b w avm fre flt re pi po fr sr w0 w1 in sy cs us sy id
1 0 0 4135188 6016 180 2 1 0 158 135 10 0 387 1821 77 20 6 74
devtotty(). devtotty() must check its arg carefully since the arg is
supplied as ioctl data. This should fix PR3004.
Renamed devtotty() to snpdevtotty().
Leave dumpdev, but kill the savecore variable. Thus, it's still off
by default, but all you need is enabling dumpdev now.
phk's old argument that savecore might inadvertendly fill up the disk
no longer counts, savecore now correctly obeyes a `minfree' file, and
we ship our systems with such a file that even has a reasonable
default.
enable in SCSISEQ during error recovery to deal with the way the
sequencer leaves selections enabled now. Add code to perform "patching"
during sequencer program download.
Spelling fixes obtained from NetBSD.
New sequencer assembler for the aic7xxx adapters. This assembler
performs some amount of register type checking, allows bit
manipulation of symbolic constants, and generates "patch tables"
for conditionalized downloading of portions of the program.
This makes it easier to take full advantage of the different
features of the aic7xxx cards without imposing run time penalies
or being bound to the small memory footprints of the low end
cards for features like target mode.
aic7xxx.reg:
New, assembler parsed, register definitions fo the aic7xxx cards.
This was done primarily in anticipation of 7810 support which
will have a different register layout, but should be able to use
the same assembler. The kernel aic7xxx driver consumes a generated
file in the compile directory to get the definitions of the register
locations.
aic7xxx.seq:
Convert to the slighly different syntax of the new assembler.
Conditionalize SCB_PAGING, ultra, and twin features which shaves
quite a bit of space once the program is downloaded.
Add code to leave the selection hardware enabled during reconnects
that win bus arbitration. This ensures that we will rearbitrate
as soon as the bus goes free instead of delaying for a bit.
When we expect the bus to go free, perform all of the cleanup
associated with that event "up front" and enter a loop awaiting
bus free. If we see a REQ first, complain, but attempt to
continue. This will hopefully address, or at least help diagnose,
the "target didn't send identify" messages that have been reported.
Spelling corrections obtained from NetBSD.
