a hard hang due to an interrupt storm or stuck interrupt pin. We
return the next IRQ that is larger than the last one returned and
in doing so give all interrupts a fair chance of being handled.
Consequently, we're able to break into the kernel debugger in such
an event.
masked-off by the firmware.
o In DELAY(). Make sure we have an inner-loop body that the compiler
cannot eliminate. While timing does not have to be perfect, the
loops must be there to have at least some notion of delay.
Obtained from: Juniper Networks
pins to determine whether there's a high register set or not. This
allows platform_gpio_init() to work without duplicating the work
done in the attach method.
get properties from the parent. The parent is in fact the FDT bus
itself and will therefore not have the properties we're looking
for.
Sponsored by: Juniper Networks
should_yield(). Use this in various places. Encapsulate the common
case of check-and-yield into a new function maybe_yield().
Change several checks for a magic number of iterations to use
should_yield() instead.
MFC after: 1 week
defined. The kernel linker doesn't deal with symbols of
type NOTYPE and typically gives the wrong symbol ($a) for
local symbols.
Obtained from: Juniper Networks, Inc.
sf buf allocation, use wakeup() instead of wakeup_one() to notify sf
buffer waiters about free buffer.
sf_buf_alloc() calls msleep(PCATCH) when SFB_CATCH flag was given,
and for simultaneous wakeup and signal delivery, msleep() returns
EINTR/ERESTART despite the thread was selected for wakeup_one(). As
result, we loose a wakeup, and some other waiter will not be woken up.
Reported and tested by: az
Reviewed by: alc, jhb
MFC after: 1 week
Compile sys/dev/mem/memutil.c for all supported platforms and remove now
unnecessary dev_mem_md_init(). Consistently define mem_range_softc from
mem.c for all platforms. Add missing #include guards for machine/memdev.h
and sys/memrange.h. Clean up some nearby style(9) nits.
MFC after: 1 month
architecture macros (__mips_n64, __powerpc64__) when 64 bit types (and
corresponding macros) are different from 32 bit. [1]
Correct the type of INT64_MIN, INT64_MAX and UINT64_MAX.
Define (U)INTMAX_C as an alias for (U)INT64_C matching the type definition
for (u)intmax_t. Do this on all architectures for consistency.
Suggested by: bde [1]
Approved by: kib (mentor)
of (unsigned) int __attribute__((__mode__(__DI__))). This aligns better
with macros such as (U)INT64_C, (U)INT64_MAX, etc. which assume (u)int64_t
has type (unsigned) long long.
The mode attribute was used because long long wasn't standardised until
C99. Nowadays compilers should support long long and use of the mode
attribute is discouraged according to GCC Internals documentation.
The type definition has to be marked with __extension__ to support
compilation with "-std=c89 -pedantic".
Discussed with: bde
Approved by: kib (mentor)
On some architectures UCHAR_MAX and USHRT_MAX had type unsigned int.
However, lacking integer suffixes for types smaller than int, their type
should correspond to that of an object of type unsigned char (or short)
when used in an expression with objects of type int. In that case unsigned
char (short) are promoted to int (i.e. signed) so the type of UCHAR_MAX and
USHRT_MAX should also be int.
Where MIN/MAX constants implicitly have the correct type the suffix has
been removed.
While here, correct some comments.
Reviewed by: bde
Approved by: kib (mentor)
It was used mainly to discover and fix some 64-bit portability problems
before 64-bit arches were widely available.
Discussed with: bde
Approved by: kib (mentor)
quite right and hasn't been used in ages and is likely broken. QEMU
with GUMSTIX is a more promising road to FreeBSD/arm in emulation
anyway.
Reviewed by: cognet@
Passing a count of zero on i386 and amd64 for [I386|AMD64]_BUS_SPACE_MEM
causes a crash/hang since the 'loop' instruction decrements the counter
before checking if it's zero.
PR: kern/80980
Discussed with: jhb
The external gpio pins are connected to a PLD on the i2c bus, unfortunatley
this device does not conform by failing to send an ack after each byte written.
The iicbb driver will abort the transfer when the address is not ack'd and it
would introduce a lot of churn to be able to pass a flag down to
iicbb_start/iicbb_write. Instead we do bad things by grabbing the iicbus but
then doing our own bit banging.
contents of the ones that were not empty were stale and unused.
- Now that <machine/mutex.h> no longer exists, there is no need to allow it
to override various helper macros in <sys/mutex.h>.
- Rename various helper macros for low-level operations on mutexes to live
in the _mtx_* or __mtx_* namespaces. While here, change the names to more
closely match the real API functions they are backing.
- Drop support for including <sys/mutex.h> in assembly source files.
Suggested by: bde (1, 2)
actually 16 I/O lines but the other ones are used for system devices and
interrupts.
The IXP4XX platform can set interrupts on these pins for
high/low/rising/falling/transitional but this is not implemented yet.
The Cambria has the same interface but as all the pins are assigned to system
functions the gpio header is toggled via a PLD on the i2c bus and is not
supported by this commit.
work properly with single-stepping in a kernel debugger. Specifically,
these routines have always disabled interrupts before increasing the nesting
count and restored the prior state of interrupts after decreasing the nesting
count to avoid problems with a nested interrupt not disabling interrupts
when acquiring a spin lock. However, trap interrupts for single-stepping
can still occur even when interrupts are disabled. Now the saved state of
interrupts is not saved in the thread until after interrupts have been
disabled and the nesting count has been increased. Similarly, the saved
state from the thread cannot be read once the nesting count has been
decreased to zero. To fix this, use temporary variables to store interrupt
state and shuffle it between the thread's MD area and the appropriate
registers.
In cooperation with: bde
MFC after: 1 month
