to do about the few cases where the HAL state isn't available (regdomain)
or isn't yet setup (probe/attach.)
The global ath_hal_debug now affects all instances of the HAL.
This also restores the ability for probe/attach debugging to work; as
the sysctl tree may not be attached at that point. Users can just set
the global "hw.ath.hal.debug" to a suitable value to enable probe/attach
related debugging.
(obvious in retrospect) in which interrupts on one CPU that are temporarily
masked can end up permanently masked when a handler on another CPU clobbers
the interrupt mask register with an old copy.
rather than global variables.
This specifically allows for debugging to be enabled per-NIC, rather
than globally.
Since the ath driver doesn't know about AH_DEBUG, and to keep the ABI
consistent regardless of whether AH_DEBUG is enabled or not, enable the
debug parameter always but only conditionally compile in the debug
methods if needed.
The ALQ support is currently still global pending some brainstorming.
Submitted by: ssgriffonuser@gmail.com
Reviewed by: adrian, bschmidt
This was previously done only for SCSI XPT in r223081, on which the change
in r223089 depended in order to respond to serial number requests. As a
result of r223089, da(4) and ada(4) devices register a d_getattr for geom to
use to obtain the information.
Reported by: ache
Reviewed by: ken
server replied NFS3ERR_JUKEBOX/NFS4ERR_DELAY to an rpc.
This affected both NFSv3 and NFSv4. Found during testing
at the recent NFSv4 interoperability Bakeathon.
MFC after: 2 weeks
alias address needs to be specified.
Add inbound handler to the alias_ftp module. It helps handle active
FTP transfer mode for the case with external clients and FTP server behind
NAT. Fix passive FTP transfer case for server behind NAT using redirect with
external IP address different from NAT ip address.
PR: kern/157957
Submitted by: Alexander V. Chernikov
was used for doing a mount when performing system operations
on AUTH_SYS mounts. This resolved an issue when mounting
a Linux server. Found during testing at the recent
NFSv4 interoperability Bakeathon.
MFC after: 2 weeks
processors unless the invariant TSC bit of CPUID is set. Intel processors
may stop incrementing TSC when DPSLP# pin is asserted, according to Intel
processor manuals, i. e., TSC timecounter is useless if the processor can
enter deep sleep state (C3/C4). This problem was accidentally uncovered by
r222869, which increased timecounter quality of P-state invariant TSC, e.g.,
for Core2 Duo T5870 (Family 6, Model f) and Atom N270 (Family 6, Model 1c).
Reported by: Fabian Keil (freebsd-listen at fabiankeil dot de)
Ian FREISLICH (ianf at clue dot co dot za)
Tested by: Fabian Keil (freebsd-listen at fabiankeil dot de)
- Core2 Duo T5870 (C3 state available/enabled)
jkim - Xeon X5150 (C3 state unavailable)
resource allocation from an x86 Host-PCI bridge driver so that it can be
reused by the ACPI Host-PCI bridge driver (and eventually the MPTable
Host-PCI bridge driver) instead of duplicating the same logic. Note that
this means that hw.acpi.host_mem_start is now replaced with the
hw.pci.host_mem_start tunable that was already used in the non-ACPI case.
This also removes hw.acpi.host_mem_start on ia64 where it was not
applicable (the implementation was very x86-specific).
While here, adjust the logic to apply the new start address on any
"wildcard" allocation even if that allocation comes from a subset of
the allowable address range.
Reviewed by: imp (1)
register both status change and link state change callbacks.
Implement checking valid link in state change callback and poll
active link state in vr_tick(). This allows immediate detection of
lost link as well as protecting driver from frequent link flips during
link renegotiation. taskq implementation was removed because driver
now needs to poll link state in vr_tick().
While I'm here do not report current link state if interface is not
running.
Tested by: n_hibma
MFC after: 1 week
o Consider No CIS a normal event and stop whining about it so much
(too many cards are like this, espeically usb/firewire cards).
o Add comments to the cis reading code.
o Made the read from config space a smidge easier to read and eliminate
a loop that can be done mathematically.
uid<->username mapping cache with an entry when another entry
for that uid is already loaded. This fixes a case where the
mapping of "toor" would replace "root" when the daemon was started,
resulting in no mapping for "root" until the cache entry for "toor"
timed out.
The algorithm is inefficient, but since it is only done once when
the daemon is started up, I don't think that's an issue.
MFC after: 2 weeks
present. Only call the bus to check if we actually do timeout so we
don't affect the normal case (since this case needn't be optimized and
this guards against all races).
