command on drives that don't like it. Right now, there's just a bogus
quirk entry in the table that doesn't do anything, but that should be
changed once we get actual inquiry data for drives that don't like the
synchronize cache command.
Also, add a shutdown hook that runs through all direct access peripherals
and runs a synchronize cache on them if they're still open, and if
synchronize cache isn't disabled via a quirk entry.
Add a synchronize cache call at the end of dadump() (again, conditionalized
on the quirk entry), so we can insure that the disk cache contents get
flushed to physical media after a dump.
Check the new quirk entry in daclose() to decide whether or not to
synchronize the cache for a disk at final close.
Reviewed by: gibbs
to convert the timeval into a tick count.
Suggested by: bde
Reviewed by: bde
Handle hz > 1000 in BIOCGRTIMEOUT.
Pointed out by: bde
Reviewed by: bde
Obtained from: OpenBSD
At some point, it will always be off from the user's POV and used
only internally to build (optionall) both mfskern floppies and
ones where mfs root and kernel go in separate places.
I'll convert sysinstall to use shortly) and a simple call which uses
this mechanism to implement an /etc/auth.conf file. I'll let Mark Murray
handle the format and checkin of the sample auth.conf file.
Reviewed by: markm
As a side effect, a few wakeup() calls are added, which might fix some of the
missing vm_page wakeups people have been seeing.
Reviewed by: Doug Rabson <dfr@nlsystems.com>
Disable DPARCKEN in the DSCOMMAND0 register on the aic7890/91/96/97.
Parity checking is broken for some chip/MB combinations and this
is the work around recommended by Adaptec.
dpt_pci.c:
Remove a superflous '{' that prevented DPT_ALLOW_MEMIO from working.
pcireg.h:
Add a definition for Parity Error Reponse bit in the PCI Space
command register.
Enable optimization for nobounce_dmamap clients by setting the map
held by the client to NULL. This allows the macros in bus.h to check
against a constant to avoid function calls.
Don't attempt to 'free()' contigmalloced pages in bus_dmamem_free().
We currently leak these pages, which is not ideal, but is better than
a panic. The leak will be fixed when contigmalloc is merged into the
bus dma framework after 3.0R.
queued.
Perform dma segment setup outside of splcam protection as this can take
some time and the protection is not necessary.
Inline a function.
Clean up some whitespace.
tagged queuing support.
Ensure that we report that a device supports tagged queuing even if
the system is waiting a "command count delay" before starting to use
them.
If a user disables disconnects on a device ensure that tagged queuing
is also turned off. We did the right thing during initial configuration,
but could be confused by manual changes.
JAZ drive happy. This shouldn't impact fast drives, and will keep cam
from failing on very slow ones (that are spinning up, say). 20
seconds was almost long enough, but not in all cases.
Suggested by: gibbs
well) Among them:
[ cd driver ]
1. Old labeling code was still there.
2. Error handling for dsopen() was broken (no test for the `error'
returned by dsopen(); bogus test of an `error' that is known to be 0).
3. cdopen() closed the physical device after certain errors although there
may still be open partitions on it.
4. cdclose() closed the physical device although there may still be open
partitions on it.
5. Some printf format fixes was incomplete or missing.
6. cdioctl() truncated unit numbers mod 256.
7. cdioctl() was missing locking.
[ da driver ]
1. daclose() closed the physical device although there may still be open
partitions on it. This was fixed many years ago in sd.c rev.1.57.
2. A minor optimization (the dk_slices != NULL test) in sdopen() became
uglier in daopen(). It is not worth doing. da only regressed compared
with od and my version of sd, since I never committed the change to sd.
daopen() should probably do less if some partition is already open.
This is not addressed by the diffs.
[ ... ]
5. "opt_hw_wdog.h" was not included, so the HW_WDOG code was unreachable.
- Added a getdev CCB call in the cdopen() and daopen() calls so that the
vendor name and device name are available for the disklabel. (suggested
by bde)
- Removed vestigal devfs support in both drivers, since we can't properly
work with devfs yet. (ask bde for details on this)
- Cleaned up the probe code in both drivers in the failure cases. There
were a number of things wrong here. The peripheral driver instances
weren't getting properly cleaned up. Sometimes the wrong probe message
would get printed out (with the failure message appended), so it wasn't
very clear that we failed to attach. SCSI sense information was printed,
even when the error in question wasn't a SCSI error. I put similar fixes
into the changer driver in revision 1.2 of scsi_ch.c.
Reviewed by: gibbs
Submitted by: bde (partially)
- Don't whine about nodes we can't stat(); these are usually
symlinks that lead out of the filesystem.
- Autoboot is now controlled by $autoboot_delay, which is a value
in seconds or NO to disable autoboot.
- Don't autoboot at the end of boot.conf if we have already tried.
- Add a 'read' command to complement 'echo'. Both are still hidden.
- Improve the 'source' command/function so that it is possible to
source scripts off removable media. The entire script is read and
saved before beginning execution. Script lines beginning with
'@' will not be echoed when being executed. Script execution will
normally terminate at the first error, however if the script line
begins with '-' this behaviour is overriden for that command.
PR: 7923
Submitted by: Archie Cobbs <archie@whistle.com>
The scandir() function returns -1 if it fails.
In many cases when this happens, it does not free
the memory that it allocated, resulting in a memory
leak, or close the directory opened with opendir().
BAD DOG, BAD!
version number part (i.e., "<directory>/perl"). Use this to
substitute #! lines in your perl5 scripts.
Requested and reviewed by: ache
(2) Add new variable WRKDIRPREFIX (defaults to ""). The "work"
directories are now in ${WRKDIRPREFIX}${.CURDIR}/work by default.
You can have a read-only ports tree (modulo any broken ports that
write something to places other than ${WRKDIR}) by setting this to
a writable location.
Ports that set WRKDIR explicitly should append this to front so
they will work when the user has WRKDIRPREFIX set.
Reviewed by: Toshihiko Kodama <kodama@ayame.mfd.cs.fujitsu.co.jp>
