this makes connect act more sensibly in these cases.
PR: 50839
Submitted by: Barney Wolff <barney@pit.databus.com>
Patch delayed by laziness of: silby
MFC after: 1 week
This version of the driver code is compatible with near-release FreeBSD 5.1
kernel/driver interfaces.
modules/Makefile, man page and other bindings to follow shortly, once I get
this part of the check-in right.
Approved by: markm(mentor)
state, as inp_socket will then be NULL. This fixes a panic that occurs when one
tries to bind a port that was previously binded with remaining TIME_WAIT
sockets.
the terminating '\0'. Since the initialisation of rootpath in
libstand/bootp.c may copy junk into the rest of the buffer, it was
possible for the code to find a ':' after the '\0' and do the wrong
thing.
Reviewed by: ps
MFC after: 1 week
resource deallocation back to fifo_close(). This eliminates any
stale data that might be stuck in the socket buffers after all the
readers and writers have closed the fifo.
Tested by: Thorsten Schroeder <ths@katjusha.de>
on friday 13th and without making a universe). This adds struct and
constant definitions for ATM traffic parameters and re-enables the
build of the midway driver.
Tested by: make universe
Previously, any normal I/O on an fdc(4) device would fail with ENXIO
if the device had been opened in non-blocking mode and then closed
prior to the conventional access; that would last until the floppy
disk was ejected and re-inserted to raise the unit attention condition.
Add a clarifying comment.
populated. Apparently, if you use an ehci controller, it's not.
Use usbd_device2interface_handle() to retrieve the interface handle.
NOTE: uaa->iface is populated in the probe routine, so I suspect the
fact that it's NULL in the attach routine is a bug in the ehci driver.
Also, don't depend on the PHY addresses returned by the AXE_CMD_READ_PHYID
command. The address is correct for my LinkSys NIC, but a user has
reported that with a D-Link NIC, the PHYID command returns address 4
while the attached Broadcom PHY is in fact strapped for address 0.
Instead, latch onto the first PHY address that returns valid data
during a readreg operation.
- Add vm page queue locking in certain places that are only needed on
sparc64.
This should make pmap_qenter and pmap_qremove MP-safe.
Discussed with: alc
as should every block device strategy routine.
There was at least one evil consequence of not doing so:
Some errors returned by fdstrategy() could be lost (EAGAIN,
in particular.)
PR: kern/52338 (in the audit-trail)
Discussed with: bde
to access floppy parameters through it.
Note: The DIOCGSECTORSIZE and DIOCGMEDIASIZE handlers withing
fdioctl() couldn't be just moved to below the existing check
for blocking mode because fd->ft can be non-NULL while still
in non-blocking mode (fd->ft can be set with the FD_STYPE ioctl.)
PR: kern/52338
No MFC: Not applicable to STABLE
schedules an upcall. Signal delivering to a bound thread is same as
non-threaded process. This is intended to be used by libpthread to
implement PTHREAD_SCOPE_SYSTEM thread.
2. Simplify kse_release() a bit, remove sleep loop.
ulpt_status() afterwards. This fixes a crash that can occur if a
USB printer is power-cycled when printing is just starting. The
problem is similar to that fixed in revision 1.33, but it is much
less likely to occur.
MFC after: 1 week
panics. Before revision 1.38, we used to just point panicstr at the
format string if panicstr was NULL, but since we now use a static
buffer for the formatted panic message, we have to be careful to
only write to it during the first panic.
Pointed out by: bde
UFS quota implementation. Push some quite broken access control
logic out of ufs_quotactl() into the individual command
implementations in ufs_quota.c; fix that logic. Pass in the thread
argument to any quotactl command that will need to perform access
control.
o quotaon() requires privilege (PRISON_ROOT).
o quotaoff() requires privilege (PRISON_ROOT).
o getquota() requires that:
If the type is USRQUOTA, either the effective uid match the
requested quota ID, that the unprivileged_get_quota flag be
set, or that the thread be privileged (PRISON_ROOT).
If the type is GRPQUOTA, require that either the thread be
a member of the group represented by the requested quota ID,
that the unprivileged_get_quota flag be set, or that the
thread be privileged (PRISON_ROOT).
o setquota() requires privilege (PRISON_ROOT).
o setuse() requires privilege (PRISON_ROOT).
o qsync() requires no special privilege (consistent with what
was present before, but probably not very useful).
Add a new sysctl, security.bsd.unprivileged_get_quota, which when
set to a non-zero value, will permit unprivileged users to query user
quotas with non-matching uids and gids. Set this to 0 by default
to be mostly consistent with the previous behavior (the same for
USRQUOTA, but not for GRPQUOTA).
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
from the tree until it is fixed. Since it is an atm driver, it isn't
commonly used so this will not negatively impact too many people.
harti can reconnect it when he resurfaces and corrects the en module
problems. This should allow snapshots to start succeeding again.
Reported by: lots of people
