just a convenience function to be called from debuggers that gets
compiled in when EHCI_DEBUG is defined. Move its declaration to
make this more obvious.
supported for STAILQ via STAILQ_CONCAT().
(2) Maintain a count of the number of entries in the thread-local entropy
fifo so that we can keep the other fifo counts in synch.
MFC after: 3 weeks
MFC with: randomdev_soft.c revisions 1.5 and 1.6
Suggested by: jhb (1)
o Reduce the interrupt delay to 2 microframes.
o Follow the spec more closely when updating the overlay qTD in the QH.
o No need to generate an interrupt at the data part of a control
transfer, it's generated by the status transfer.
o Make sure to update the data toggle on short transfers.
o Turn the printf about needing toggle update into a DPRINTF.
o Keep track of what high speed port (if any) a device belongs to
so we can set the transaction translator fields for the transfer.
o Verbosely refuse to open low/full speed pipes that depend on
unimplemented split transaction support.
o Fix various typos in comments.
Obtained from: NetBSD
control the number of lines per page rather than a constant. The variable
can be examined and changed in ddb as '$lines'. Setting the variable to
0 will effectively turn off paging.
- Change db_putchar() to force out pending whitespace before outputting
newlines and carriage returns so that one can rub out content on the
current line via '\r \r' type strings.
- Change the simple pager to rub out the --More-- prompt explicitly when
the routine exits.
- Add some aliases to the simple pager to make it more compatible with
more(1): 'e' and 'j' do a single line. 'd' does half a page, and
'f' does a full page.
MFC after: 1 month
Inspired by: kris
* Announce some more fields from ro area for better debugging of broken
sk(4)s on various boards.
Submitted by: Bjoern A. Zeeb <bzeeb-lists@lists.zabbadoz.net>
entered the interface start function, no packets were actually dequeued.
Therefore, keep a count of how many packets we really added onto the tx
chain, and initiate a transmit only if the count is non-zero.
the device is suspended or shutting down. This will need to be rethought
slightly if we implement suspend/resume support within vr(4).
This appears to fix the vr_shutdown() panic on SMP machines.
My theory here is there's a race somewhere during vr_detach() with
vr_intr() in the SMP case which was sometimes being triggered,
although quite why this was happening is unclear (vr_stop() also
explicitly disables interrupts by writing to the IMR register).
MFC-to-RELENG_5* candidate.
PR: kern/62889
Tested by: seb at struchtrup dot com
MFC after: 10 days
on UltraSPARC workstations. The driver is based on OpenBSD's SBus
cs4231 driver and heavily modified to incorporate into sound(4)
infrastructure. Due to the lack of APCDMA documentation, the DMA
code of SBus cs4231 came from OpenBSD's driver.
The driver runs without Giant lock and supports both SBus and EBus
based CS4231 audio controller. Special thanks to marius for providing
feedbacks during the driver writing. His feedback made it possible
to write hiccup free playback code under high system loads.
Approved by: jake (mentor)
Reviewed by: marius (initial version)
Tested by: marius, kwm, Julian C. Dunn(jdunn AT opentrend DOT net)
two loops in agp_generic_bind_memory(). As an intended side-effect, all
of the calls to vm_page_wakeup() are now performed with the containing
vm object lock held.
o Instead of locking and unlocking all over the place, use
lock assertions to make certain that the bfe lock is held
where necessary.
o Create locked and unlocked versions of bfe_init and bfe_start. These
functions can be called from outside the module and by functions
within the bfe module. The calls from outside the module don't
hold the bfe lock so the unlocked versions called by these functions
simple obtain the bfe lock and call the locked version.
- Fix a typo (scp) in the locking macros that only worked because in all the
instances in which it was called the softc pointer happened to be named 'sc'.
- Mark the interrupt MPSAFE
Tested by: matusita, Dario Freni <saturnero@gufi.org>
Silence from: -net, wpaul
with a weak memory model or x86 + PAE (or more specifically, your
driver is using bounce pages) and you have had problems with em(4),
this may fix it. At least this is needed to have em(4) work properly
on FreeBSD/arm.
Original version by: cognet
Reviewed by: tackerman
Tested by: cognet
Add constants for SPI protocol delays that are needed for
target mode.
aic7xxx.c:
Correct a target mode issue that caused an occassional
spurious REQ to be seen on the bus when performing manual
message processing (e.g. transfer rate negotiation).
Enforce phase change bus settle rules with explicit
delays when performing manual message processing in
target mode. The sequencer already did this for
"fast-path", target mode message processing.
as the original logic did. This fixes a race with vr_intr() which was
masked on UP systems and manifested on SMP systems.
PR: kern/62889
MFC after: 1 day
the ATA pccard locking function. This makes pccard devices like
Compact Flash cards work again.
PR: kern/72805
Submitted by: James E. Flemer <jflemer@alum.rpi.edu>
MFC in: 2 days
frames. BGE hardware with the rx alignment bug will still be handled by the
calls to m_adj() that already exist. m_adj() is probably better suited for
this task anyways. Just as with if_em, this saves a malloc + several locks
per packet and prevents unneeded data copying within busdma.
Since the e1000 DMA engines hava no constraints on the alignment of buffer
transfers, there is no reason to tell busdma that there is. This save a
minimum of 1 malloc call per packet, which translates to eliminating 4 locks.
It also means that buffers are not needlessly bounced when transfered. The
end result is a 38% improvement in pps in a 4 way bridging environment.
Obtained from: Sandvine, Inc.
(usually taking 20 seconds to transmit a packet).. no longer fall back
to only transmitting one packet (instead of the entire queue) after we
have processed the entire send queue... I have no idea why we didn't
start seeing this problem ~6 years ago when this code was introduced...
modes on a tty structure.
Both the ".init" and the current settings are initialized allowing
the function to be used both at attach and open time.
The function takes an argument to decide if echoing should be enabled.
Echoing should not be enabled for regular physical serial ports
unless they are consoles, in which case they should be configured
by ttyconsolemode() instead.
Use the new function throughout.
constrained to a small number of sessions by the small on-card memories found
in newer devices. This is really a stopgap solution as having session state
in main memory incurs a (small but noticeable) performance penalty. The better
solution is to manage session state so that it's cached on chip.
Obtained from: openbsd
The changes in the next commit would make the code totally unreadable
if the #ifdef'ing were maintained.
It might make a lot of sense to split if_cx.c in a netgraph related
and in a tty related file but I will not attempt that without hardware.
handle DMA addresses located above 1GB. The LBA(loop begin address)
register which holds DMA base address is 32bits register. But the
MSB 2bits are used for other purposes. This effectivly limits the
DMA address space up to 1GB.
Approved by: jake (mentor)
Reviewed by: truckman, matk
assign DMA address to the wrong address. It can cause system lockup
or other mysterious errors. Since most sound cards requires low DMA
address(BUS_SPACE_MAXADDR_24BIT) sndbuf_alloc() would fail when the
audio driver is loaded after long running of operations.
Approved by: jake (mentor)
Reviewed by: truckman, matk
- Implement dcons_ischar() and dcons_load_buffer().
- If loader passed a dcons buffer address, keep using it.
(We still need a patch to cheat memory management system.)
asynchronous. I realize that this means the custom application will
not work as written, but it is not okay to break most users of ugen(4).
The major problem is that a bulk read transfer is not an interrupt
saying that X bytes are available -- it is a request to be able to
receive up to X bytes, with T timeout, and S short-transfer-okayness.
The timeout is a software mechanism that ugen(4) provides and cannot
be implemented using asynchronous reads -- the timeout must start at
the time a read is done.
The status of up to how many bytes can be received in this transfer
and whether a short transfer returns data or error is also encoded
at least in ohci(4)'s requests to the controller. Trying to detect
the "maximum width" results in using a single buffer of far too
small when an application requests a large read.
Even if you combat this by replacing all buffers again with the
maximal sized read buffer (1kb) that ugen(4) would allow you to
use before, you don't get the right semantics -- you have to
throw data away or make all the timeouts invalid or make the
short-transfer settings invalid.
There is no way to do this right without extending the ugen(4) API
much further -- it breaks the USB camera interfaces used because
they need a chain of many maximal-width transfers, for example, and
it makes cross-platform support for all the BSDs gratuitously hard.
Instead of trying to do select(2) on a bulk read pipe -- which has
neither the information on desired transfer length nor ability to
implement timeout -- an application can simply use a kernel thread
and pipe to turn that endpoint into something poll-able.
It is unfortunate that bulk endpoints cannot provide the same semantics
that interrupt and isochronous endpoints can, but it is possible to just
use ioctl(USB_GET_ENDPOINT_DESC) to find out when different semantics
must be used without preventing the normal users of the ugen(4) device
from working.
New devicename is ttyy{unit}{port}
No callout devices created as there is no modemcontrol on these ports.
Add data structure to represent each port to avoid excessive array use.
from within umass_ufi_transform(). This includes the 12-byte commands
FORMAT_UNIT, WRITE_AND_VERIFY, VERIFY, and READ_FORMAT_CAPACITIES
(sorted in numerical order).
Reviewed by: ken, scottl
MFC after: 2 weeks
md(8). The former is generally not going to fail, but the latter can
fail when the underlying swap device returns an error.
There are still plenty of other places where vm_pager_get_pages() failing
will lead directly to crashes, so it's a good idea to put your swap on
RAID if you care enough to put any of your disks on RAID....
that conjures up the device node so it isn't true PNP. Noticed by jhb@.
* Add an attachment for esscontrol since it too uses ISA_PNP_PROBE.
* Move an attachment from snd_mss to snd_pnpmss. The latter is the real
PNP user.
* Fix a bug where caches were flushed on non-C3 transitions.
* Be sure a working flush cache instruction is present before using it.
* Disable C3 completely if it isn't present.
