As this is evaluation hardware with only a few users, and there is a lack
of information add a warning when booting on this hardware.
Reported by: cognet
Obtained from: ABT Systems Ltd
MFC after: Instant
Sponsored by: The FreeBSD Foundation
This paves the way for further attach/detach code reorganization.
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7858
In case if there is already running interface, a second non-sta
interface will omit scanning, going directly to RUN state. Handle
this case for adhoc mode appropriately.
Tested with RTL8821AU, 2 vaps in IBSS mode.
In particular, reset the DF_QUIET flag when detaching from a device so
that a driver that marks a device quiet doesn't dictate policy for a
different driver that may claim the device in the future.
Reviewed by: rpokala, wblock
MFC after: 2 weeks
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7803
- Certain pic_assign_cpu, e.g. msi_assign_cpu can have quite a long
call chain. For msi_assign_cpu, mutex makes complex PCI bridge
drivers more tricky, e.g. sleep can note be called, etc, it will
be pretty tricky for upcoming Hyper-V PCI bridge driver for PCI
pass-through.
- It is not used on any hot code path nor non-sleepable context, so
sx should have the same effect as mutex.
PIC list is still protected by mutex to keep suspend/resume work.
Discussed with: jhb
Reviewed by: jhb
MFC after: 3 weeks
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7784
* Don't do RTS/CTS - experiments show that we get ACK frames for each of them
and this ends up causing the timestamps to look all funny.
* Set the HAL_TXDESC_POS bit, so the AR9300 HAL sets up the hardware to return
location and CSI information.
- evdev_set_methods call is not required if actual methods are no-ops
- evdev_set_serial is also optional if there is no meaningful input device
identifier
- evdev_set_id on the other hand is mandatory, so set virtual bus with
dummy vendor/product/version
Suggested by: Vladimir Kondratiev
Add generic evdev support to touchscreen part of ti_adc: two absolute
coordinates + button touch to indicate pen position. Pressure value
reporting is not implemented yet.
Tested on: Beaglebone Black + 4DCAPE-43T + tslib
evdev is a generic input event interface compatible with Linux
evdev API at ioctl level. It allows using unmodified (apart from
header name) input evdev drivers in Xorg, Wayland, Qt.
This commit has only generic kernel API. evdev support for individual
hardware drivers like ukbd, ums, atkbd, etc. will be committed later.
Project was started by Jakub Klama as part of GSoC 2014. Jakub's
evdev implementation was later used as a base, updated and finished
by Vladimir Kondratiev.
Submitted by: Vladimir Kondratiev <wulf@cicgroup.ru>
Reviewed by: adrian, hans
Differential Revision: https://reviews.freebsd.org/D6998
libifconfig is still experimental and under active development.
To avoid making any ABI promises, mark the library as private
Suggested by: bapt
Reviewed by: kp
The flag specifies that the block which uses FPU must be executed in
critical section, i.e. take no context switches, and does not need an
FPU save area during the execution.
It is intended to be applied around fast and short code pathes where
save area allocation is impossible or undesirable, due to context or
due to the relative cost of calculation vs. allocation.
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Previously the flag returned by cap_getmode was not described explicitly
in the man page.
Reviewed by: wblock
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D7822
Rename registers as in the manual.
Do a hard reset of the controller before a soft one.
Since DMA is always used remove dependancy on allwinner_soc_family, it was used
to differentiate SoC as the fdt compatible string were the same.
Tested on A10, A20, H3 and A64.
Reviewed by: jmcneill
Differential Revision: https://reviews.freebsd.org/D6868
