Correct annotations where NULL input can be permitted
Submitted by: Richard Houldsworth <rhouldsworth at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D18284
Submitted by: Andy Moreton <amoreton at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D18283
In efx_mcdi_phy_module_get_info() probe the
transceiver identification byte rather than assume
the module matches the fixed port type. This
supports scenarios such as a SFP mounted in a QSFP
port via a QSA module.
Submitted by: Richard Houldsworth <rhouldsworth at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D18282
Add a function which makes an MCDI GET_LINK request and
packages up the results. Currently, the get-link function
is triggered from several entry points which then pass
on or store selected parts of the data. When the driver
needs to obtain the current link state, it is more
efficient to do this in a single call.
Submitted by: Richard Houldsworth <rhouldsworth at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D18281
Previously only some of the code was guarded by this which caused
a build error when EFSYS_OPT_RX_SCALE is 0 (e.g. in manftest).
Submitted by: Tom Millington <tmillington at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D18280
Limit the port mode bandwidth calculations by the maximum
reported link speed. This system detects 25G vs 10G cards,
and 100G port modes vs 40G.
Submitted by: Richard Houldsworth <rhouldsworth at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D18279
Change the interface to ef10_nic_get_port_mode_bandwidth()
so more NIC information can be used to infer bandwidth
requirements. Huntington calculations separated out
completely.
Submitted by: Richard Houldsworth <rhouldsworth at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D18278
Add cases for the new port modes supported by X2 NICs.
Lane bandwidth is calculated for pre-X2 cards so is an
underestimate for X2 in 25G/100G modes.
Submitted by: Richard Houldsworth <rhouldsworth at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D18277
>From Medford onwards, the newer constants enumerating
port modes should be used.
Submitted by: Richard Houldsworth <rhouldsworth at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D18276
Adjust data types in interface to permit the complete
module information buffer to be obtained in a single
call.
Submitted by: Richard Houldsworth <rhouldsworth at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D18275
Rearrange so the valid addresses are visible to the caller.
Submitted by: Richard Houldsworth <rhouldsworth at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D18274
Adjust bounds so the interface supports reading
the last available byte of data.
Submitted by: Richard Houldsworth <rhouldsworth at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D18273
This statistic should include 64byte and smaller frames.
Fix EF10 calculation to match Siena code.
Submitted by: Andy Moreton <amoreton at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D18271
The capability bits to request FEC modes are implicitly valid
when the corresponding FEC mode is a supported capability.
Drivers expect that it is only valid to advertise those
capabilities explicitly marked as supported. The capabilities
reported by firmware is modified with the implicit capabilities
to present the explicit model to drivers.
Submitted by: Richard Houldsworth <rhouldsworth at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D18270
Client drivers may use either legacy flags, for example,
EFX_RX_HASH_TCPIPV4, or generalised flags, for example,
EFX_RX_HASH(IPV4_TCP, 4TUPLE), to configure RSS hash.
The libefx is able to recognise what scheme is used.
Legacy flags may be consumed directly by a chip-specific handler to
configure the NIC, that is, on EF10, these flags can be used to fill
in legacy RSS mode field in MCDI request. Generalised flags can also
be directly used in EF10-specific handler as they are fully compatible
with additional fields of the same MCDI request.
Legacy flags undergo conversion to generalised flags before they
are consumed by a chip-specific handler. This conversion is used to
make sure that chip-specific handlers expect only generalised flags
in the input for the sake of clarity of the code.
Depending on firmware capabilities, a chip-specififc handler either
supplies the input to the NIC directly, for example,
EFX_RX_HASH(IPV4_TCP, 4TUPLE) flag will enable 4 bits in
RSS_CONTEXT_SET_FLAGS_IN_TCP_IPV4_RSS_MODE field on EF10, or takes
the opportunity to translate the input to enable bits which don't map
to the generic flag, like setting
RSS_CONTEXT_SET_FLAGS_IN_TOEPLITZ_TCPV4_EN on EF10 when the firmware
claims no support for additional modes.
However, this approach has introduced a severe problem which can be
reproduced with ultra-low-latency firmware variant. In order to enable
IP hash, EF10-specific handler requires the user to request 2-tuple
hash for IP-other, TCP and UDP traffic classes, unconditionally.
In example, IPv4 hash can be enabled using the following input:
EFX_RX_HASH(IPV4_TCP, 2TUPLE) | EFX_RX_HASH(IPV4_UDP, 2TUPLE) |
EFX_RX_HASH(IPV4, 2TUPLE).
At the same time, on ultra-low-latency firmware, the common code will
never report support for any UDP tuple to the client driver. That is,
in the same example, the driver will use EFX_RX_HASH(IPV4_TCP, 2TUPLE) |
EFX_RX_HASH(IPV4, 2TUPLE). This input will not be recognised by
EF10-specific handler, and RSS_CONTEXT_SET_FLAGS_IN_TOEPLITZ_IPV4_EN
bit will not be set in the MCDI request.
In order to solve the problem, the patch removes conversion code
from chip-specific handlers and adds appropriate code to convert
EFX_RX_HASH() flags to their legacy counterparts to the common scale
mode set function. If the firmware does not support additional modes,
the function will convert generalised flags to legacy flags correctly
without any demand for UDP flags and pass the result to a chip-specific
handler.
Submitted by: Ivan Malov <ivan.malov at oktetlabs.ru>
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D18269
RSS mode bits can be accessed a lot easier in the hash
type value provided that the variable type is uint32_t.
The macro helper can be removed to enhance readability.
Submitted by: Ivan Malov <ivan.malov at oktetlabs.ru>
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D18268
The efx_rx_scale_hash_flags_get interface is unsafe, as it does not
have an argument for the size of the output buffer used to return
the flags. While the only caller currently supplies a sufficiently
large buffer, this should be checked at runtime to avoid writing
past the end of the buffer.
Submitted by: Ivan Malov <ivan.malov at oktetlabs.ru>
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D18267
The API which is used to list supported hash flags verifies
hash algorithm choice before writing the output. This check
is based on a switch() statement which has only two options
and no distinctive actions to be conducted for each of them.
Use simpler code instead of switch() to improve readability.
Submitted by: Ivan Malov <ivan.malov at oktetlabs.ru>
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D18266
NIC config is initialized during NIC probe.
Submitted by: Mark Spender <mspender at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D18263
The efx_nic_hw_unavailable() checks ensure that if the NIC hardware
has failed or has been physically removed then libefx will stop
further attempts to access the hardware.
Add an interface for libefx clients to force unavailability, so the
hardware is treated as dead or removed even if still physically present.
Submitted by: Andy Moreton <amoreton at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D18261
Add efx_nic_hw_unavailable() routine to check for hardware presence
before continuing with NIC operations.
Submitted by: Andy Moreton <amoreton at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D18260
Introduce and use macro to make sure that MCDI buffers allocated
on stack are rounded up properly.
Submitted by: Gautam Dawar <gdawar at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D18259
In SF bug 61297 it's been confirmed that the hardware does not always
calculate the TCP checksum correctly with TSO sends.
The value of the Total Length field (IPv4) or Payload Length field
(IPv6) is the critical factor. We're sufficiently confident that if
these fields are zero then the checksum will be calculated correctly.
The information may be used by the drivers to check if the workaround is
required when FATSOv2 is implemented.
Submitted by: Mark Spender <mspender at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D18258
Found by PreFAST static analysis.
Submitted by: Martin Harvey <mharvey at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D18257
The SFN driver's PartitionControl WMI object requires an API to parse
and filter partition data in TLV format, particularly for the Dynamic
Config partition. The ef10_nvram_buffer functions provide this
functionality but are tied to use with license partition only.
Modify functions so they are applicable to all TLV partitions and add
functions to support in-place tag modification.
Submitted by: Richard Houldsworth <rhouldsworth at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D18256
Extend efx_mcdi_get_port_modes() to optionally pass on the default
port mode field. This provides a more direct way of handling the case
where the dynamic config does not specify the port mode than the
alternative of a lookup table indexed by MCFW subtype.
Submitted by: Richard Houldsworth <rhouldsworth at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D18255
Functions to process the DHCP option list format used by the expansion
ROM config buffers, to support extracting and updating of individual
options.
The initial use case is the driver presenting the global and per-PF
options as separate items, with the driver implementing the
synchronization of global options across the configuration buffers
for all PFs.
Submitted by: Richard Houldsworth <rhouldsworth at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D18254
Submitted by: Martin Harvey <mharvey at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D18253
Size of provided memory should be consistent with specified size.
Submitted by: Martin Harvey <mharvey at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D18252
Description of sensors is generated from firmware sources.
Submitted by: Martin Harvey <mharvey at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D18251
No need for probe messages when a TxQ is too full for a post to be done.
Existing drivers check if there is room in the queue before posting
descriptors, even though efx_tx_qdesc_post() does the check itself.
The new SFN Windows driver doesn't perform the check before calling
efx_tx_qdesc_post(), but that means these probes can get frequently
printed out. It's normal driver behaviour so there's no need to print
an error.
Submitted by: Mark Spender <mspender at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D18250
Remove obsolete monitor types since Falcon SFN4000 series adapters
no longer supported by libefx.
Rename MCDI monitors to be consistent with YML.
The code may be simplified and generalized since only MCDI monitors
remain.
Submitted by: Martin Harvey <mharvey at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D18249
Move empty definitions for platform-specific annotations from efsys.h
to EFX headers.
Submitted by: Martin Harvey <mharvey at solarflare.com>
Submitted by: Andrew Lee <alee at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
Differential Revision: https://reviews.freebsd.org/D18248
This applies the fix in r283924 to the vm.objects sysctl
added by r283624 so the output will include the vnode
information (i.e. path) for tmpfs objects.
Reviewed by: kib, dab
MFC after: 2 weeks
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D2724
Also remove logic to avoid unnecessary stores to the global variable.
Thread creation and destruction are heavy enough that any supposed savings
is in the noise.
MFC after: 2 weeks
Sponsored by: Dell EMC Isilon
For non-ERMS case the code used handle possible trailing bytes with
movsb first and then followed it up with movsq. This also happened
to alter how calculations were done for other cases.
Handle the tail with regular movs, just like when copying forward.
Use leaq to calculate the right offset from the get go, instead of
doing separate add and sub.
This adjusts the offset for non-rep cases so that they can be used
to handle the tail.
The routine is still a work in progress.
Sponsored by: The FreeBSD Foundation
This fixes builds of kernels without INET6 such as LINT-NOINET6.
Reported by: arybchik
Reviewed by: np
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D18384
