Contrary to the rateset information in legacy frames the MCS Set
field also contains TX capability information in cases where the
number of available TX and RX spartial streams differ. Because a
rateset doesn't contain that information we have to pull the
those directly from the hardware capabilities.
Get rid of the assumption that every device is capable of 40MHz,
SGI and 2 spartial streams. Instead of printing, in the worst case,
8 times 76 MCS rates, print logically connect ranges and the
support RX/TX streams.
A device without 40MHz and SGI support looks like:
ath0: 2T2R
ath0: 11na MCS 20Mhz
ath0: MCS 0-7: 6.5Mbps - 65Mbps
ath0: MCS 8-15: 13Mbps - 130Mbps
ath0: 11ng MCS 20Mhz
ath0: MCS 0-7: 6.5Mbps - 65Mbps
ath0: MCS 8-15: 13Mbps - 130Mbps
Initialize ic_rxstream/ic_txstream with 2, for compatibility reasons.
Introduce 4 new HTC flags, which are used in addition to ic_rxstream
and ic_txstream to compute the hc_mcsset content and also for initializing
ni_htrates. The number of spatial streams is enough to determine support
for MCS0-31 but not for MCS32-76 as well as some TX parameters in the
hc_mcsset field.
adjust the IEEE80211_HTRATE_MAXSIZE constant, only MCS0 - 76 are valid
the other bits in the mcsset IE (77 - 127) are either reserved or used
for TX parameters.
clean up parts of the *_recv_mgmt() functions.
- make sure appropriate counters are bumped and debug messages are printed
- order the unhandled subtypes by value and add a few missing ones
- fix some whitespace nits
- remove duplicate code in adhoc_recv_mgmt()
- remove a useless comment, probably left in while c&p
The current code transmits management and multicast frames at MCS 0.
What it should do is check whether the negotiated basic set is zero (and
the MCS set is not) before making this decision.
For now, simply default to the lowest negotiated rate, rather than
MCS 0. This fixes the behaviour with at least the DLINK DIR-825, which
ACKs but silently ignores block-ack (BA) response frames.
if a scan is running, report if a scan has been started. The return value
itself is not (yet) used anywhere in the tree and it is also not exported
to userspace.
MFC after: 1 month
the element's data length, frm[2] is the first byte of the element's data.
Submitted by: Monthadar Al Jaberi <monthadar at gmail.com>
MFC after: 1 week
This fixes hostap mode for at least ral(4) and run(4), because there is
no sufficient call into drivers which could be used initialize the node
related ratectl variables.
MFC after: 3 days
beacon or probe-response frames. Fix the condition by checking for the
the array's content instead of the always existing array itself.
Reviewed by: rpaulo, stefanf
MFC after: 3 days
its internal data. This has been used to bypass missing calls in drivers
which do not use the ratectl framework correctly. Issue is, not all algos
use that variable, or even have internal data, therefore valid calls are
not done. Fix this by removing the checks, all driver issues should be
resolved.
MFC after: 1 week
the currently selected rate. The calculations of course need a valid
rate. To make that possible before any call to node_rate() is done,
initialize ni_txrate on none_node_init() calls.
MFC after: 1 week
the IEEE80211_C_RATECTL flag set, default to NONE for all drivers. Only if
a driver calls ieee80211_ratectl_init() check if the NONE algo is still
selected and try to use AMRR in that case. Drivers are still free to use
any other algo by calling ieee80211_ratectl_set() prior to the
ieee80211_ratectl_init() call.
After this change it is now safe to assume that a ratectl algo is always
available and selected, which renders the IEEE80211_C_RATECTL flag pretty
much useless. Therefore revert r211314 and 211546.
Reviewed by: rpaulo
MFC after: 2 weeks
This can happen if the algos are built as modules but are not loaded. If
the selected ratectl algo is not available, try to load it (The load
module functions does nothing currently). Add a dummy ratectl algo which
always selects the first available rate. Use that one if the desired algo
is not available.
MFC after: 1 week
802.11 duplicate detection. Upon looking at the standard, we discover
that 802.11-2007 says:
"A receiving QoS STA is also required to keep only the most recent
cache entry per<Address 2, TID, sequence-number> triple, storing only
the most recently received fragment number for that triple. A receiving
STA may omit tuples obtained from broadcast/multicast or ATIM frames
from the cache."
To fix this, we just disable duplicate detection for multicast/broadcast
frames.
Reviewed by: sam
MFC after: 4 weeks
Obtained from: DragonFly
queue length. The default value for this parameter is 50, which is
quite low for many of today's uses and the only way to modify this
parameter right now is to edit if_var.h file. Also add read-only
sysctl with the same name, so that it's possible to retrieve the
current value.
MFC after: 1 month
ratectl_node_init() functions and since ni_rtctls was already
malloc'ed() we will panic. Fix this by using the already malloc'ed
pointer.
Found by: bschmidt
Reviewed by: bschmidt
* WPA-None requires ap_scan=2:
The major difference between ap_scan=1 (default) and 2 is, that no
IEEE80211_IOC_SCAN* ioctls/functions are called, though, there is a
dependency on those. For example the call to wpa_driver_bsd_scan()
sets the interface UP, this never happens, therefore the interface
must be marked up in wpa_driver_bsd_associate(). IEEE80211_IOC_SSID
also is not called, which means that the SSID has not been set prior
to the IEEE80211_MLME_ASSOC call.
* WPA-None has no support for sequence number updates, it doesn't make
sense to check for replay violations..
* I had some crashes right after the switch to RUN state, issue is
that sc->sc_lastrs was not yet defined.
Approved by: rpaulo (mentor)
MFC after: 3 weeks
This framework allows drivers to abstract the rate control algorithm and
just feed the framework with the usable parameters. The rate control
framework will now deal with passing the parameters to the selected
algorithm. Right now we have AMRR (the default) and RSSADAPT but there's
no way to select one with ifconfig, yet.
The objective is to have more rate control algorithms in the net80211
stack so all drivers[0] can use it. Ideally, we'll have the well-known
sample rate control algorithm in the net80211 at some point so all
drivers can use it (not just ath).
[0] all drivers that do rate control in software, that is.
Reviewed by: bschmidt, thompsa, weyongo
MFC after: 1 months
