to the pci attachment. Cardbus is a derived class of pci so all pci
drivers are automatically available for matching against cardbus devices.
Reviewed by: imp
if_xname, if_dname, and if_dunit. if_xname is the name of the interface
and if_dname/unit are the driver name and instance.
This change paves the way for interface renaming and enhanced pseudo
device creation and configuration symantics.
Approved By: re (in principle)
Reviewed By: njl, imp
Tested On: i386, amd64, sparc64
Obtained From: NetBSD (if_xname)
register, present only on 3c90xB and later NICs. This meant that you could
not use a 1500 byte MTU with VLANs on original 3c905/3c900 cards (boomerang
chipset). The boomerang chip does support large frames though, just not
in the same way: you can set the 'allow large frames' bit in the MAC
control register to receive frames up to 4K in size.
Changes:
- Set the 'allow large frames' bit for boomerang chips and increase
the packet size register for cyclone and later chips. This allows
us to use IFCAP_VLAN_MTU on all supported xl(4) NICs.
- Actually set the IFCAP_VLAN_MTU flag in the capabilities word
in xl_attach().
- Change the method used to detect older boomerang chips. My 3c575C
cardbus NIC was being incorrectly identified as 3c90x chip instead
of 3c90xB because the capabilities word in its EEPROM reports
a bizzare value. In addition to checking for the supportsNoTxLength
bit, also check for the absence of the supportsLargePackets bit.
Both of these cases denote a 3c90xB chip.
- Make RX and TX checksums configurable via the SIOCSIFCAP ioctl.
- Avoid an unecessary le32toh() in xl_rxeof(): we already have the
received frame size in the lower 16 bits of rxstat, no need to
read it again.
Tested with 3c905-TX, 3c900-TPO, 3c980C and 3c575C NICs.
BUS_DMA_NOWAIT flag, since the code can't handle this.
- Use NULL, NULL for the lockfunc and lockfuncarg parameters of
bus_dma_tag_create() since deferred loads can't happen now.
forced to do slightly bogus power state manipulation. However, this
is one of those features that is preventing further progress, so mark
them as BURN_BIRDGES like I did for the drivers in sys/dev/...
This, like the other change, are a no-op unless you have BURN_BRIDGES
in your kernel.
Add two new arguments to bus_dma_tag_create(): lockfunc and lockfuncarg.
Lockfunc allows a driver to provide a function for managing its locking
semantics while using busdma. At the moment, this is used for the
asynchronous busdma_swi and callback mechanism. Two lockfunc implementations
are provided: busdma_lock_mutex() performs standard mutex operations on the
mutex that is specified from lockfuncarg. dftl_lock() is a panic
implementation and is defaulted to when NULL, NULL are passed to
bus_dma_tag_create(). The only time that NULL, NULL should ever be used is
when the driver ensures that bus_dmamap_load() will not be deferred.
Drivers that do not provide their own locking can pass
busdma_lock_mutex,&Giant args in order to preserve the former behaviour.
sparc64 and powerpc do not provide real busdma_swi functions, so this is
largely a noop on those platforms. The busdma_swi on is64 is not properly
locked yet, so warnings will be emitted on this platform when busdma
callback deferrals happen.
If anyone gets panics or warnings from dflt_lock() being called, please
let me know right away.
Reviewed by: tmm, gibbs
mapped I/O mode, we pause for .1 seconds after issuing the reset command
before trying to poll the 'command busy' bit in the status register.
With my 3c575C cardbus NIC, my Sony Picturebook locks up when it tries
to read the status register immediately after the reset. This appears
to be a problem only with certain NICs on certain hardware, but the
added delay should not hurt cards that already work.
This bug seems to have been brought to light by the fact that the xl
driver now defaults to memory mapped I/O mode instead of programmed
I/O mode like it used to. With PIO mode, the delay isn't needed and
everything works (which is why this NIC worked with 5.0-RELEASE but
not 5.1). I suspect that what's happening is that when the chip is
reset, it takes a little while for the memory-mapped decoding logic
to recover. Trying to access the chip's registers during this period
causes an error condition of some kind that wedges the system.
if attach succeeded. device_is_alive just tells us that probe
succeeded. Since we were using it to do things like detach net
interfaces, this caused problems when there were errors in the attach
routine.
Symptoms of problem reported by: martin blapp
- Unconditionally call *_stop() if device is in the tree. This is to
prevent callouts from happening after the device is gone. Checks for
bus_child_present() should be added in the future to keep from touching
potentially non-existent hardware in *_detach(). Found by iedowse@.
- Always check for and free miibus children, even if the device is not in
the tree since some failure cases could have gotten here.
- Call ether_ifdetach() in the irq setup failure case
- ti(4), xl(4): move ifmedia_init() calls to the beginning of attach so
that ifmedia_removeall() can be unconditionally called on detach. There
is no way to detect whether ifmedia has been initialized without using
a separate variable (as tl(4) does).
- Add comments to indicate assumptions of code path
network layer (ether).
- Don't abuse module names to facilitate ifconfig module loading;
such abuse isn't really needed. (And if we do need type information
associated with a module then we should make it explicit and not
use hacks.)
properly (likely due to mbuf exhaustion.) Previously, the driver
got somewhat wedged.
Also, remove the annoying messages printed every time xl_encap
couldn't allocate a mbuf; they served no useful purpose, and just made
an mbuf exhaustion situation more annoying.
MFC after: 1 week
RX part of this driver too. It's better since the code wasn't
dealing with bus_dmamap_load() returning EINPROGRESS, and this
can't happen with bus_dmamap_load_mbuf().
Submitted by: jake
- Remove locking of the softc in the attach method, instead depending on
bus_setup_intr being at the end of attach (delaying interrupt enable until
after ether_ifattach is called)
- Call *_detach directly in the error case of attach, depending on checking
in detach to only free resources that were allocated. This puts all
resource freeing in one place, avoiding thinkos that lead to memory leaks.
- Add bus_child_present check to calls to *_stop in the detach method to
be sure hw is present before touching its registers.
- Remove bzero softc calls since device_t should do this for us.
- dc: move interrupt allocation back where it was before. It was unnecessary
to move it. This reverts part of 1.88
- rl: move irq allocation before ether_ifattach. Problems might have been
caused by allocating the irq after enabling interrupts on the card.
- rl: call rl_stop before ether_ifdetach
- sf: call sf_stop before ether_ifdetach
- sis: add missed free of sis_tag
- sis: check errors from tag creation
- sis: move dmamem_alloc and dmamap_load to happen at same time as tag creation
- sk: remove duplicate initialization of sk_dev
- ste: add missed bus_generic_detach
- ti: call ti_stop before ether_ifdetach
- ti: add missed error setting in ti_rdata alloc failure
- vr: add missed error setting in I/O, memory mapping cases
- xl: add missed error setting in I/O, memory mapping cases
- xl: remove multi-level goto on attach failure
- xl: move dmamem_alloc and dmamap_load to happen at same time as tag creation
- Calls to free(9) are unconditional because it is valid to call free with a
null pointer.
Reviewed by: imp, mdodd
code messed up on B & C chipsets because it lost the packet header
and therefore the flag indicating the need for hardware checksums.
MFC after: 2 weeks
driver should use port or memory based IO, determine it dynamically
at runtime, preferring MMIO where possible. This helps us support newer
arches which dislike port based access better.
Tested on i386 & sparc64, with 3c900, 905, 905b, and 905C cards.
(in varying combinations by both jake and myself)
as opposed to one after the other. This is faster in both -CURRENT
and -STABLE. Additionally, there is less code duplication for
error-checking.
One thing to note is that this code seems to return(1) when no buffers
are available; perhaps ENOBUFS should be the correct return value?
Partially submitted & tested by: Hiten Pandya <hiten@unixdaemons.com>
MFC after: 1 week
wish the busdma APIs were more consistent accross architectures.
We should probably move all the other DMA map creations in
xl_attach() where we can really handle them failing, since
xl_init() is void and shouldn't fail.
Pointy hat to: mux
Tested by: Anders Andersson <anders@hack.org>
bus_dmamap_load() it.
- Make it so reusing mbufs when we can't allocate (or map) new ones
actually works. We were previously trying to reuse a mbuf which
was already bus_dmamap_unload()'ed.
Reviewed by: silby
- Add conversions to/from little endian for fields that the NIC accesses
by DMA as required.
- Add some bus_dmamap_sync() calls, and correct some existing ones.
- Read the receiver information from the EEPROM in an endian-neutral
manner.
- Load all RX and TX descriptors in a single DMA map up front, and
get the bus addresses of individual descriptors by address arithmetic;
this fixes multiple use of the descriptor tags, which would have
undesired effects.
It seems that xl still does not work on e250 boxen, for reasons which
are not clear yet.
Reviewed by: mux
is read one clock edge too late. This bit is driven low by
slave (as any other input data bits from slave) when the clock
is LOW. The current code did read the bit after the clock was
driven high again.
Reviewed by: luoqi
MFC after: 2 weeks
bus_dmamap_load_mbuf() returned EFBIG.
o Fix mbuf leaks in an error (rare) code path.
o Reuse the TX descriptor if xl_encap() failed instead of
just picking the next one.
o Better error messages.
it possible to use this driver under ia64, sparc64 (though
there may be endianness issues with this one) and other archs.
Tested on: i386, alpha (gallatin)
o use if_input for input packet processing
o don't strip the Ethernet header for input packets
o use BPF_* macros bpf tapping
o call ether_ioctl to handle default ioctl case
o track vlan changes
Reviewed by: many
Approved by: re
