case where the controller is already enabled.
Some of the pl310 configuration registers cannot be changed while the
controller is active, so if there is any platform-specific init to be done
it must happen before enabling the controller.
The controller should not be enabled upon entry to the kernel, but u-boot
has recently developed the bad habit of leaving caches enabled when
launching the kernel, and since we have no control over that source code
we have to do our best to cope with it. The PL310 manual doesn't document
a safe sequence for disabling the controller, but the sequence used here
(force write-through mode and disable linefill allocations, then clean and
invalidate the current contents before disabling the hardware) appears to
be sound both by analysis and empirical testing.
These changes were developed and tested in collaboration with
Svatopluk Kraus <onwahe@gmail.com>.
Reviewed by: cognet@
instead of from /usr/share/mk.
I'm not sure that this will let buildworld complete on a system with
no installed src.opts.mk (make buildworld is still running), but the
tinderbox builds are all failing earlyon without this patch.
controller driver by piggybacking the SOF interrupt when issuing new
and checking old transfers. Number of interrupts was reduced by 30%
when doing Isochronous transfers.
Use correct GINTMSK_XXX macros when accessing the DWC OTG interrupt
mask register.
Add code to adjust the frame interval register which influences the
SOF rate.
MFC after: 2 weeks
This problem only occurs on versions of FreeBSD prior to the recent CAM
locking changes. (i.e. stable/9 and older versions of stable/10) This
change should be a no-op for head and stable/10.
If a path isn't specified, xpt_register_async() will create a fully
wildcarded path and acquire a lock (the XPT lock in older versions,
and via xpt_path_lock() in newer versions) to call xpt_action() for the
XPT_SASYNC_CB CCB. It will then drop the lock and if the requested event
includes AC_FOUND_DEVICE or AC_PATH_REGISTERED, it will get the caller up
to date with any device arrivals or path registrations.
The issue is that before the locking changes, each SIM lock would get
acquired in turn during the EDT tree traversal process. If a path is
specified for xpt_register_async(), it won't acquire and drop its own lock,
but instead expects the caller to hold its own SIM lock. That works for
the first part of xpt_register_async(), but causes a recursive lock
acquisition once the EDT traversal happens and it comes to the SIM in
question. And it isn't possible to call xpt_action() without holding a SIM
lock.
The locking changes fix this by using the XPT topology lock for EDT
traversal, so it is no longer an issue to hold the SIM lock while calling
xpt_register_async().
The solution for FreeBSD versions before the locking changes is to request
notification of all device arrivals (so we pass a NULL path into
xpt_register_async()) and then filter out the arrivals that are not ours.
MFC After: 3 days
Sponsored by: Spectra Logic Corporation
build world, so it is the only make we build or install. fmake is
still in the tree, but disconnected, and upgrades from older systems
that still have bmake has not been removed, but its state has not been
tested (it should work given how minimal the work to upgrade to bmake
is).
/etc/src.conf to this file as well. Now, it will only affect builds of
/usr/src and not others that use the bsd.*.mk files. Specifically
don't install src.opts.mk so we can catch when it 'leaks' into
bsd.*.mk again and have there be errors when this happens. Future
commits will move to including src.opts.mk instead of bsd.own.mk when
all that's needed is one of the MK_FOO options from src.opts.mk.
Future options should be placed here, unless they directly affect a
bsd.*.mk file, in which case they should be placed in bsd.opts.mk.
periodically update the reference status of the active pages. This function
was called, instead of vm_pageout_scan(), when memory was not scarce. The
objective was to provide up to date reference status for active pages in
case memory did become scarce and active pages needed to be deactivated.
The active page queue scan performed by vm_pageout_page_stats() was
virtually identical to that performed by vm_pageout_scan(), and so r254304
eliminated vm_pageout_page_stats(). Instead, vm_pageout_scan() is
called with the parameter "pass" set to zero. The intention was that when
pass is zero, vm_pageout_scan() would only scan the active queue. However,
the variable page_shortage can still be greater than zero when memory is not
scarce and vm_pageout_scan() is called with pass equal to zero.
Consequently, the inactive queue may be scanned and dirty pages laundered
even though that was not intended by r254304. This revision fixes that.
Reported by: avg
MFC after: 1 week
Sponsored by: EMC / Isilon Storage Division
used.
It turns out that the RX DMA engine does the same last-descriptor-link-
pointer-re-reading trick that the TX DMA engine. That is, the hardware
re-reads the link pointer before it moves onto the next descriptor.
Thus we can't free a descriptor before we move on; it's possible the
hardware will need to re-read the link pointer before we overwrite
it with a new one.
Tested:
* AR5416, STA mode
TODO:
* more thorough AP and STA mode testing!
* test on other pre-AR9380 NICs, just to be sure.
* Break out the RX descriptor grabbing bits from the RX completion
bits, like what is done in the RX EDMA code, so ..
* .. the RX lock can be held during ath_rx_proc(), but not across
packet input.
same events that tcpstat's tcps_rcvmemdrop counter counts.
- Rename tcps_rcvmemdrop to tcps_rcvreassfull and improve its
description in netstat(1) output.
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
Failing to do this will cause the kevent(2) notification to trigger
continuously and the bhyve(8) mevent thread will hog the cpu until the
characters on the backend tty device are drained.
Also, make the uart backend file descriptor non-blocking to avoid a
select(2) before every byte read from that backend.
Reviewed by: grehan
'Relnotes:' tag in case 'yes' is not explicitly
the first string value following the tab.
As it turns out, a number of commits have bypassed
my filters (both email and 'svn log --search'), and
this script returns the results I want when doing
these searches.
Sponsored by: The FreeBSD Foundation
thicket of .if ${COMPILER_TYPE} == "clang" that controls
warnings. Also, use CFLAGS.clang in a couple places in preference to
having a similar construct that's related to the CWARNFLAGS changes.
default. This restores more of the historical expectations that
were broken when we started disallowing both WITH_FOO and
WITHOUT_FOO to be defined.
[2] Document this new behavior, and improve the documentation in
general here.
Submitted by: sjg@ [1].
o Declare vt(4) drivers dataset.
o Create single static structures for all early drivers.
o Add vt(4) to be by default in the kernel consoles list.
o Create one more sysinit point, to be able to initialize memory and lock
requirement of early drivers.
o Implement early drivers select. (Only best available will be selected).
o Fix one missed "return (0)" for VTYLOCK.
o Improve locking for cases when one driver replace another.
o Make driver replacement notification less debug-look-like.
Minor spell fixes.
Sponsored by: The FreeBSD Foundation
reflect when unmapped I/O support was added.
For FreeBSD 10, it arrived just prior to __FreeBSD_version 1000028.
For FreeBSD 9, it arrived just prior to __FreeBSD_version 902001.
Also, fix compiler warnings in mprsas_send_smpcmd() that happen in the
i386 PAE build for non-unmapped I/O builds. These were fixed in mps(4)
in revision 241145, but didn't make it into the mpr(4) driver. This
change should only affect FreeBSD versions outside the above revisions,
and thus doesn't affect head.
MFC after: 3 days
Sponsored by: Spectra Logic Corporation
melifaro, we agreed that ifconfig's behavior was not a bug. The main
motivation for bin/187551 was to partially resolve kern/187549, but we
resolved kern/187549 in a different way instead.
ObsoleteFiles.inc
etc/mtree/BSD.tests.dist
sbin/ifconfig/tests/fibs_test.sh
sbin/ifconfig/tests/Makefile
sbin/ifconfig/Makefile
Remove /usr/tests/sbin/ifconfig
PR: bin/187551
MFC after: 3 days
Sponsored by: Spectra Logic
a 'hostcpu'. The new format of the argument string is "vcpu:hostcpu".
This allows pinning a subset of the vcpus if desired.
It also allows pinning a vcpu to more than a single 'hostcpu'.
Submitted by: novel (initial version)
However, if the original knote had been disabled then it is not automatically
re-enabled.
Fix this by using EV_ADD to create an mevent and EV_ENABLE to enable it.
Adding a kevent for the first time implicitly enables it so existing callers
of mevent_add() don't need to change.
Reviewed by: grehan
rman_reserve_resource_bound() to return incorrect results.
Continue the initial search until the first viable region is found.
Add a comment to explain the search termination test.
PR: kern/188534
Reviewed by: jhb (previous version)
MFC after: 1 week
