- In sys/ofed/drivers/infiniband/core/cma.c, an enum struct member is
interpreted as an int, so cast it to an int.
- In sys/ofed/drivers/infiniband/core/ud_header.c, initialize the
packet_length variable in ib_ud_header_init(), to prevent undefined
behaviour.
- In sys/ofed/drivers/infiniband/ulp/sdp/sdp_rx.c, call rdma_notify()
with the correct enum type and value.
- In sys/ofed/include/linux/pci.h, change the PCI_DEVICE and PCI_VDEVICE
macros to use C99 struct initializers, so additional members can be
overridden.
Reviewed by: delphij, Garrett Cooper <yanegomi@gmail.com>
MFC after: 1 week
There is one known issue: Some probes will display an error message along the
lines of: "Invalid address (0)"
I tested this with both a simple dtrace probe and dtruss on a few different
binaries on 32-bit. I only compiled 64-bit, did not run it, but I don't expect
problems without the modules loaded. Volunteers are welcome.
MFC after: 1 month
warns about unused variables in this code, so always add -Wno-unused to
the warning flags. Why gcc on x86 *doesn't* warn about this, I will never
know. The code itself should probably be fixed at some point.
GIANT from VFS. In addition, disconnect also netsmb, which is a base
requirement for SMBFS.
In the while SMBFS regular users can use FUSE interface and smbnetfs
port to work with their SMBFS partitions.
Also, there are ongoing efforts by vendor to support in-kernel smbfs,
so there are good chances that it will get relinked once properly locked.
This is not targeted for MFC.
GIANT from VFS. This code is particulary broken and fragile and other
in-kernel implementations around, found in other operating systems,
don't really seem clean and solid enough to be imported at all.
If someone wants to reconsider in-kernel NTFS implementation for
inclusion again, a fair effort for completely fixing and cleaning it
up is expected.
In the while NTFS regular users can use FUSE interface and ntfs-3g
port to work with their NTFS partitions.
This is not targeted for MFC.
GIANT from VFS. In addition, disconnect also netncp, which is a base
requirement for NWFS.
In the possibility of a future maintenance of the code and later
readd to the FreeBSD base, maybe we should think about a better location
for netncp. I'm not entirely sure the / top location is actually right,
however I will let network people to comment on that more specifically.
This is not targeted for MFC.
sdchi encapsulates a generic SD Host Controller logic that relies on
actual hardware driver for register access.
sdhci_pci implements driver for PCI SDHC controllers using new SDHCI
interface
No kernel config modifications are required, but if you load sdhc
as a module you must switch to sdhci_pci instead.
This has been developed during 2 summer of code mandates and being revived
by gnn recently.
The functionality in this commit mirrors entirely content of fusefs-kmod
port, which doesn't need to be installed anymore for -CURRENT setups.
In order to get some sparse technical notes, please refer to:
http://lists.freebsd.org/pipermail/freebsd-fs/2012-March/013876.html
or to the project branch:
svn://svn.freebsd.org/base/projects/fuse/
which also contains granular history of changes happened during port
refinements. This commit does not came from the branch reintegration
itself because it seems svn is not behaving properly for this functionaly
at the moment.
Partly Sponsored by: Google, Summer of Code program 2005, 2011
Originally submitted by: ilya, Csaba Henk <csaba-ml AT creo DOT hu >
In collabouration with: pho
Tested by: flo, gnn, Gustau Perez,
Kevin Oberman <rkoberman AT gmail DOT com>
MFC after: 2 months
The code builds a map of regions that were freed. On every write the
code consults the map and eventually removes ranges that were freed
before, but are now overwritten.
Freed blocks are not TRIMed immediately. There is a tunable that defines
how many txg we should wait with TRIMming freed blocks (64 by default).
There is a low priority thread that TRIMs ranges when the time comes.
During TRIM we keep in-flight ranges on a list to detect colliding
writes - we have to delay writes that collide with in-flight TRIMs in
case something will be reordered and write will reached the disk before
the TRIM. We don't have to do the same for in-flight writes, as
colliding writes just remove ranges to TRIM.
Sponsored by: multiplay.co.uk
This work includes some important fixes and some improvements obtained
from the zfsonlinux project, including TRIMming entire vdevs on pool
create/add/attach and on pool import for spare and cache vdevs.
Obtained from: zfsonlinux
Submitted by: Etienne Dechamps <etienne.dechamps@ovh.net>
reside, and move there ipfw(4) and pf(4).
o Move most modified parts of pf out of contrib.
Actual movements:
sys/contrib/pf/net/*.c -> sys/netpfil/pf/
sys/contrib/pf/net/*.h -> sys/net/
contrib/pf/pfctl/*.c -> sbin/pfctl
contrib/pf/pfctl/*.h -> sbin/pfctl
contrib/pf/pfctl/pfctl.8 -> sbin/pfctl
contrib/pf/pfctl/*.4 -> share/man/man4
contrib/pf/pfctl/*.5 -> share/man/man5
sys/netinet/ipfw -> sys/netpfil/ipfw
The arguable movement is pf/net/*.h -> sys/net. There are
future plans to refactor pf includes, so I decided not to
break things twice.
Not modified bits of pf left in contrib: authpf, ftp-proxy,
tftp-proxy, pflogd.
The ipfw(4) movement is planned to be merged to stable/9,
to make head and stable match.
Discussed with: bz, luigi
generator, found on IvyBridge and supposedly later CPUs, accessible
with RDRAND instruction.
From the Intel whitepapers and articles about Bull Mountain, it seems
that we do not need to perform post-processing of RDRAND results, like
AES-encryption of the data with random IV and keys, which was done for
Padlock. Intel claims that sanitization is performed in hardware.
Make both Padlock and Bull Mountain random generators support code
covered by kernel config options, for the benefit of people who prefer
minimal kernels. Also add the tunables to disable hardware generator
even if detected.
Reviewed by: markm, secteam (simon)
Tested by: bapt, Michael Moll <kvedulv@kvedulv.de>
MFC after: 3 weeks
warnings in sys/gnu/fs/xfs. The only warnings that still need to be
suppressed are those about array bound overruns of flexible array
members in xfs_dir2_{block,sf}.c, which are too expensive (in terms of
cascading code changes) to fix.
MFC after: 1 week
X-MFC-With: r239959
linking it statically into the kernel. With our gcc in base there are
no warnings, so also remove the WERROR= from the module makefile.
Noted by: Eir Nym <eirnym@gmail.com>
MFC after: 1 week
Basically, this is automatic rx zero copy when feasible. TCP payload is
DMA'd directly into the userspace buffer described by the uio submitted
in soreceive by an application.
- Works with sockets that are being handled by the TCP offload engine
of a T4 chip (you need t4_tom.ko module loaded after cxgbe, and an
"ifconfig +toe" on the cxgbe interface).
- Does not require any modification to the application.
- Not enabled by default. Use hw.t4nex.<X>.toe.ddp="1" to enable it.
'encapsulating interface' used with IPsec and has nothing to do with
storage 'enclosure' services.
MFC after: 3 days
Noticed while: debugging why enc(4) is no longer automatically created
subdevice ahciem. Emulate SEMB SES device from AHCI LED interface to expose
it to users in form of ses(4) CAM device. If we ever see AHCI controllers
supporting SES of SAF-TE over I2C as described by specification, they should
fit well into this new picture.
Sponsored by: iXsystems, Inc.
* Introduce TX DMA setup/teardown methods, mirroring what's done in
the RX path.
Although the TX DMA descriptor is setup via ath_desc_alloc() /
ath_desc_free(), there TX status descriptor ring will be allocated
in this path.
* Remove some of the TX EDMA capability probing from the RX path and
push it into the new TX EDMA path.
These probes are most useful when looking into the structures
they provide, which are listed in io.d. For example:
dtrace -n 'io:genunix::start { printf("%d\n", args[0]->bio_bcount); }'
Note that the I/O systems in FreeBSD and Solaris/Illumos are sufficiently
different that there is not a 1:1 mapping from scripts that work
with one to the other.
MFC after: 1 month
shared code update and small changes in core required
Add support for new i210/i211 devices
Improve queue calculation based on mac type
MFC after:5 days
Asus laptops. It is alike to acpi_asus(4), but uses WMI interface instead
of separate ACPI device.
On Asus EeePC T101MT netbook it allows to handle hotkeys and on/off WLAN,
Bluetooth, LCD backlight, camera, cardreader and touchpad.
On Asus UX31A ultrabook it allows to handle hotkeys, on/off WLAN, Bluetooth,
Wireless LED, control keyboard backlight brightness, monitor temperature
and fan speed. LCD brightness control doesn't work now for unknown reason,
possibly requiring some video card initialization.
Sponsored by: iXsystems, Inc.
- Stateful TCP offload drivers for Terminator 3 and 4 (T3 and T4) ASICs.
These are available as t3_tom and t4_tom modules that augment cxgb(4)
and cxgbe(4) respectively. The cxgb/cxgbe drivers continue to work as
usual with or without these extra features.
- iWARP driver for Terminator 3 ASIC (kernel verbs). T4 iWARP in the
works and will follow soon.
Build-tested with make universe.
30s overview
============
What interfaces support TCP offload? Look for TOE4 and/or TOE6 in the
capabilities of an interface:
# ifconfig -m | grep TOE
Enable/disable TCP offload on an interface (just like any other ifnet
capability):
# ifconfig cxgbe0 toe
# ifconfig cxgbe0 -toe
Which connections are offloaded? Look for toe4 and/or toe6 in the
output of netstat and sockstat:
# netstat -np tcp | grep toe
# sockstat -46c | grep toe
Reviewed by: bz, gnn
Sponsored by: Chelsio communications.
MFC after: ~3 months (after 9.1, and after ensuring MFC is feasible)
Add TSO6 and LRO/IPv6 support.
Fix the module Makefile to at least properly inlcude opt_inet6.h
and allow builds without INET or INET6.
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
Reviewed by: gnn (as part of the whole)
MFC After: 3 days
Allow LRO to work on IPv6 as well.
Fix the module Makefile to at least properly inlcude opt_inet6.h
and allow builds without INET or INET6.
Sponsored by: The FreeBSD Foundation
Sponsored by: iXsystems
Reviewed by: gnn (as part of the whole)
MFC After: 3 days
Revamp the CAM enclosure services driver.
This updated driver uses an in-kernel daemon to track state changes and
publishes physical path location information\for disk elements into the
CAM device database.
Sponsored by: Spectra Logic Corporation
Sponsored by: iXsystems, Inc.
Submitted by: gibbs, will, mav
operations required by GEMified i915.ko. It also attaches to SandyBridge
and IvyBridge CPU northbridges now.
Sponsored by: The FreeBSD Foundation
MFC after: 1 month
There's some TX path TDMA code in if_ath_tx.c which should be migrated
out, but first I should likely try and verify/fix/repair the TDMA support
in 9.x and -HEAD.
The NAND Flash environment consists of several distinct components:
- NAND framework (drivers harness for NAND controllers and NAND chips)
- NAND simulator (NANDsim)
- NAND file system (NAND FS)
- Companion tools and utilities
- Documentation (manual pages)
This work is still experimental. Please use with caution.
Obtained from: Semihalf
Supported by: FreeBSD Foundation, Juniper Networks
defined by the SNIA Common RAID Disk Data Format Specification v2.0.
Supports multiple volumes per array and multiple partitions per disk.
Supports standard big-endian and Adaptec's little-endian byte ordering.
Supports all single-layer RAID levels. Dual-layer RAID levels except
RAID10 are not supported now because of GEOM RAID design limitations.
Some work is still to be done, but the present code already manages basic
interoperation with RAID BIOS of the Adaptec 1430SA SATA RAID controller.
MFC after: 1 month
Sponsored by: iXsystems, Inc.
- When switching to 4-bit operation, send a SET_CLR_CARD_DETECT command
to disconnect the card-detect pull-up resistor from the DAT3 line before
sending the SET_BUS_WIDTH command.
- Add the missing "reserved" zero entry to the mantissa table used to
decode various CSD fields. This was causing SD cards to report that they
could run at 30 MHz instead of the maximum 25 MHz mandated in the spec.
o Enhancements:
- At the MMC layer, format various info from the CID into a string that
uniquely identifies the card instance (manufacturer number, serial
number, product name and revision, etc). Export it as an instance
variable.
- At the MMCSD layer, display the formatted card ID string, and also
report the clock speed of the hardware (not the card's max speed), and
the number of bits and number of blocks per transfer. It comes out like
this now:
mmcsd0: 968MB <SD SD01G 8.0 SN 276886905 MFG 08/2008 by 3 SD> at mmc0
22.5MHz/4bit/128-block
o Use DEVMETHOD_END.
o Use NULL instead of 0 for pointers.
PR: 156496
Submitted by: Ian Lepore
MFC after: 1 week
- Mark 'sdp' as requiring 'inet'.
- Always include "opt_inet.h" and "opt_inet6.h" and modify the IB
driver Makefiles to honor WITH/WITHOUT_INET/INET6/_SUPPORT options
to determine what should be enabled during a module build.
- Fix the mlxen(4) driver and the core IB code to compile without
if INET is disabled (including when both INET and INET6 are disabled).
Reviewed by: bz
MFC after: 2 weeks
First cut of new HW support from LSI and merge into FreeBSD.
Supports Drake Skinny and ThunderBolt cards.
MFhead_mfi r227574
Style
MFhead_mfi r227579
Use bus_addr_t instead of uintXX_t.
MFhead_mfi r227580
MSI support
MFhead_mfi r227612
More bus_addr_t and remove "#ifdef __amd64__".
MFhead_mfi r227905
Improved timeout support from Scott.
MFhead_mfi r228108
Make file.
MFhead_mfi r228208
Fixed botched merge of Skinny support and enhanced handling
in call back routine.
MFhead_mfi r228279
Remove superfluous !TAILQ_EMPTY() checks before TAILQ_FOREACH().
MFhead_mfi r228310
Move mfi_decode_evt() to taskqueue.
MFhead_mfi r228320
Implement MFI_DEBUG for 64bit S/G lists.
MFhead_mfi r231988
Restore structure layout by reverting the array header to
use [0] instead of [1].
MFhead_mfi r232412
Put wildcard pattern later in the match table.
MFhead_mfi r232413
Use lower case for hexadecimal numbers to match surrounding
style.
MFhead_mfi r232414
Add more Thunderbolt variants.
MFhead_mfi r232888
Don't act on events prior to boot or when shutting down.
Add hw.mfi.detect_jbod_change to enable or disable acting
on JBOD type of disks being added on insert and removed on
removing. Switch hw.mfi.msi to 1 by default since it works
better on newer cards.
MFhead_mfi r233016
Release driver lock before taking Giant when deleting children.
Use TAILQ_FOREACH_SAFE when items can be deleted. Make code a
little simplier to follow. Fix a couple more style issues.
MFhead_mfi r233620
Update mfi_spare/mfi_array with the actual number of elements
for array_ref and pd. Change these max. #define names to avoid
name space collisions. This will require an update to mfiutil
It avoids mfiutil having to do a magic calculation.
Add a note and #define to state that a "SYSTEM" disk is really
what the firmware calls a "JBOD" drive.
Thanks to the many that helped, LSI for the initial code drop,
mav, delphij, jhb, sbruno that all helped with code and testing.
New kernel events can be added at various location for sampling or counting.
This will for example allow easy system profiling whatever the processor is
with known tools like pmcstat(8).
Simultaneous usage of software PMC and hardware PMC is possible, for example
looking at the lock acquire failure, page fault while sampling on
instructions.
Sponsored by: NETASQ
MFC after: 1 month
sys/dev/mps/mps_sas.c:861:1: error: function 'mpssas_discovery_timeout' is not needed and will not be emitted [-Werror,-Wunneeded-internal-declaration]
mpssas_discovery_timeout(void *data)
^
Because the driver is obtained from upstream, we don't want to modify
it; just silence the warning instead, it is harmless.
MFC after: 3 days
Winbond Super I/O chips.
With minor efforts it should be possible the extend the driver to support
further chips/revisions available from Winbond. In the simplest case
only new IDs need to be added, while different chipsets might require
their own function to enter extended function mode, etc.
Sponsored by: Sandvine Incorporated ULC (in 2011)
Reviewed by: emaste, brueffer
MFC after: 2 weeks
get rid of testing explicitly for clang (using ${CC:T:Mclang}) in
individual Makefiles.
Instead, use the following extra macros, for use with clang:
- NO_WERROR.clang (disables -Werror)
- NO_WCAST_ALIGN.clang (disables -Wcast-align)
- NO_WFORMAT.clang (disables -Wformat and friends)
- CLANG_NO_IAS (disables integrated assembler)
- CLANG_OPT_SMALL (adds flags for extra small size optimizations)
As a side effect, this enables setting CC/CXX/CPP in src.conf instead of
make.conf! For clang, use the following:
CC=clang
CXX=clang++
CPP=clang-cpp
MFC after: 2 weeks
sys/dev/hpt27xx/osm_bsd.c, since it gets the following warnings:
sys/dev/hpt27xx/osm_bsd.c:1180:25: error: format string is not a string literal (potentially insecure) [-Werror,-Wformat-security]
S_IRUSR | S_IWUSR, driver_name);
^~~~~~~~~~~
@/dev/hpt27xx/hpt27xx_config.h:46:21: note: expanded from:
#define driver_name hpt27xx_driver_name
^~~~~~~~~~~~~~~~~~~
Since 'hpt27xx_driver_name' is a constant string symbol (coming from the
proprietary hpt27xx_lib.o file), there is no security problem.
Because this driver is provided by the vendor, and applying changes
requires re-certification and other bureaucratic exercises, just disable
the warning for now.
MFC after: 1 week
with clang. Also fix a number of warnings uncovered when building with
clang around some implicit enum conversions.
Sponsored by: Intel
Approved by: scottl
kernel modules that include binary-only code.
More fine-grained control is provided via MK_SOURCELESS_HOST (for native code
that runs on host CPU) and MK_SOURCELESS_UCODE (for microcode).
Reviewed by: julian, delphij, freebsd-arch
Approved by: kib (mentor)
MFC after: 2 weeks
The isci driver is for the integrated SAS controller in the Intel C600
(Patsburg) chipset. Source files in sys/dev/isci directory are
FreeBSD-specific, and sys/dev/isci/scil subdirectory contains
an OS-agnostic library (SCIL) published by Intel to control the SAS
controller. This library is used primarily as-is in this driver, with
some post-processing to better integrate into the kernel build
environment.
isci.4 and a README in the sys/dev/isci directory contain a few
additional details.
This driver is only built for amd64 and i386 targets.
Sponsored by: Intel
Reviewed by: scottl
Approved by: scottl
This involves significant changes to the mps(4) driver, but is not a
complete rewrite.
Some of the changes in this version of the driver:
- Integrated RAID (IR) support.
- Support for WarpDrive controllers.
- Support for SCSI protection information (EEDP).
- Support for TLR (Transport Level Retries), needed for tape drives.
- Improved error recovery code.
- ioctl interface compatible with LSI utilities.
mps.4: Update the mps(4) driver man page somewhat for the driver
changes. The list of supported hardware still needs to be
updated to reflect the full list of supported cards.
conf/files: Add the new driver files.
mps/mpi/*: Updated version of the MPI header files, with a BSD style
copyright.
mps/*: See above for a description of the new driver features.
modules/mps/Makefile:
Add the new mps(4) driver files.
Submitted by: Kashyap Desai <Kashyap.Desai@lsi.com>
Reviewed by: ken
MFC after: 1 week
versions derived from /usr/ports/audio/oss.
The particular headers used were taken from the
attic/drv/oss_allegro directory and are mostly identical
to the previous files.
The Maestro3 driver is now free from the GPL.
NOTE: due to lack of testers this driver is being
considered for deprecation and removal.
PR: kern/153920
Approved by: jhb (mentor)
MFC after: 2 weeks
is used.
Although the module _builds_, it fails to load because of a missing symbol from
ieee80211_tdma.c.
Specifics:
* Always build ieee80211_tdma.c in the module;
* only compile in the code if IEEE80211_SUPPORT_TDMA is defined.
The USB code as it stands includes the bus glue along _with_ the controller
code. So the ohci/ehci modules actually build the USB controller code and
the PCI bus glue.
It'd be nice to ship separate modules for the PCI glue and the USB
controller (so for example if there were a USB controller hanging off
the internal SoC bus as well as an external PCI device) it could be done.
This is primarily done to save a few bytes here and there on embedded
systems with limited flash space for kernels - a very limited (sub-1MB)
space may be available for the kernel and may only support gzip encoding.
The rootfs can be LZMA compressed.
This is primarily done to save a few bytes here and there on embedded
systems with limited flash space for kernels - a very limited (sub-1MB)
space may be available for the kernel and may only support gzip encoding.
The rootfs can be LZMA compressed.
- Huge old hdac driver was split into three independent pieces: HDA
controller driver (hdac), HDA CODEC driver (hdacc) and HDA sudio function
driver (hdaa).
- Support for multichannel recording was added. Now, as specification
defines, driver checks input associations for pins with sequence numbers
14 and 15, and if found (usually) -- works as before, mixing signals
together. If it doesn't, it configures input association as multichannel.
- Signal tracer was improved to look for cases where several DACs/ADCs in
CODEC can work with the same audio signal. If such case found, driver
registers additional playback/record stream (channel) for the pcm device.
- New controller streams reservation mechanism was implemented. That
allows to have more pcm devices then streams supported by the controller
(usually 4 in each direction). Now it limits only number of simultaneously
transferred audio streams, that is rarely reachable and properly reported
if happens.
- Codec pins and GPIO signals configuration was exported via set of
writable sysctls. Another sysctl dev.hdaa.X.reconfig allows to trigger
driver reconfiguration in run-time.
- Driver now decodes pins location and connector type names. In some cases
it allows to hint user where on the system case connectors, related to the
pcm device, are located. Number of channels supported by pcm device,
reported now (if it is not 2), should also make search easier.
- Added workaround for digital mic on some Asus laptops/netbooks.
MFC after: 2 months
Sponsored by: iXsystems, Inc.
This uses the emuxkireg.h already used in the emu10k1
snd driver. Special thanks go to Alexander Motin as
he was able to find some errors and reverse engineer
some wrong values in the emuxkireg header.
The emu10kx driver is now free from the GPL.
PR: 153901
Tested by: mav, joel
Approved by: jhb (mentor)
MFC after: 2 weeks
This introduces:
* a basic wtap interface
* a HAL, which implements an abstraction layer for implementing
different device behavious;
* A visibility plugin, which allows for control over which nodes
see other nodes (useful for mesh work.)
It doesn't yet implement sta/adhoc/hostap modes but these are quite
feasible to implement.
Monthadar uses it to do 802.11s mesh verification.
The userland tools will be committed in a follow-up commit.
Submitted by: Monthadar Al Jaberi <monthadar@gmail.com>
opt_ah.h file if KERNBUILDDIR isn't defined.
For now, AH_SUPPORT_AR5416 is required, so I'll just fix any
configuration file in /usr/src which is missing this option.
Pointy hat when things do break to: adrian
This brings in the emuxkireg.h from NetBSD (dev/pci) which
is used for the same purpose but is smaller. The emu10k1
is now free from the GPL.
PR: 153901
Obtained from: NetBSD
Approved by: core (mentor implicit)
MFC after: 2 weeks
All of these are harmless, and are in fact used to shut up warnings from
lint.
While here, remove -Wno-missing-prototypes from the xfs module
Makefile, as I could not reproduce those warnings either with gcc or
clang.
MFC after: 1 week
with clang. There are several macros in these files that return values,
and in some cases nothing is done with them, but it is completely
harmless. For some other files, also disable -Wconstant-conversion,
since that triggers a false positive with the DMA_BIT_MASK() macro.
MFC after: 1 week
with clang:
sys/dev/ce/tau32-ddk.c:1228:37: warning: implicit truncation from 'int' to bitfield changes value from 65532 to 8188 [-Wconstant-conversion]
Since this file is obfuscated C, we can never determine (in a sane way,
at least :) if this points to a real problem or not. The driver has
been in the tree for more than five years, so it most likely isn't.
MFC after: 1 week
- Device configuration via plain text config file. Also able to operate
when not attached to the chip as the master driver.
- Generic "work request" queue that serves as the base for both ctrl and
ofld tx queues.
- Generic interrupt handler routine that can process any event on any
kind of ingress queue (via a dispatch table).
- A couple of new driver ioctls. cxgbetool can now install a firmware
to the card ("loadfw" command) and can read the card's memory
("memdump" and "tcb" commands).
- Lots of assorted information within dev.t4nex.X.misc.* This is
primarily for debugging and won't show up in sysctl -a.
- Code to manage the L2 tables on the chip.
- Updates to cxgbe(4) man page to go with the tunables that have changed.
- Updates to the shared code in common/
- Updates to the driver-firmware interface (now at fw 1.4.16.0)
MFC after: 1 month
This patch should remove the need for kldunload of USB
controller drivers at suspend and kldload of USB controller
drivers at resume.
This patch also fixes some build issues in avr32dci.c
MFC after: 2 weeks
Tested on Qemu/KVM, VirtualBox, and BHyVe.
Currently built as modules-only on i386/amd64. Man pages not yet hooked
up, pending review.
Submitted by: Bryan Venteicher bryanv at daemoninthecloset dot org
Reviewed by: bz
MFC after: 4 weeks or so
based on Solarflare SFC9000 family controllers. The driver supports jumbo
frames, transmit/receive checksum offload, TCP Segmentation Offload (TSO),
Large Receive Offload (LRO), VLAN checksum offload, VLAN TSO, and Receive Side
Scaling (RSS) using MSI-X interrupts.
This work was sponsored by Solarflare Communications, Inc.
My sincere thanks to Ben Hutchings for doing a lot of the hard work!
Sponsored by: Solarflare Communications, Inc.
MFC after: 3 weeks
results in the HAL being built without HAL debugging/diagnostic support,
the module building process needs to be somehow taught to not build AR5416+
NICs if AH_SUPPORT_AR5416 isn't defined in opt_ah.h .
This implies that users who are building the driver do so with
KERNBUILDDIR set to the compile/CONFIG directory so the various
opt_* sources can be pulled in.
compiled into the kernel.
Do not try to build the module in case of no INET support but
keep #error calls for now in case we would compile it into the
kernel.
This should fix an issue where the module would fail to enable
IPv6 support from the rc framework, but also other INET and INET6
parts being silently compiled out without giving a warning in the
module case.
While here garbage collect unneeded opt_*.h includes.
opt_ipdn.h is not used anywhere but we need to leave the DUMMYNET
entry in options for conditional inclusion in kernel so keep the
file with the same name.
Reported by: pluknet
Reviewed by: plunket, jhb
MFC After: 3 days
Specifically, add support for "Drake Skinny" and "ThunderBolt" LSI
cards.
Initial code was supplied by LSI under BSD license. Several improvements
were done by myself. Such things like making it work in a static kernel,
be able to boot of the RAID, performance improvements. I removed some
fairly complicated code that seemed to directly access the disks under
the firmware. It doesn't seem to be needed and significantly slowed
down the performance of the driver and caused tons of sense errors to
be reported.
This code is being checked in this area so others can help me get it into
shape to commit into the FreeBSD tree. Assistance has been volunteered
by iXsystems.
We might want to re-work the JBOD attachment that creates /dev/mfisyspd?
node for each disk.
Performance is faster then prior cards. It works okay with WITNESS
and INVARIANTS on amd64 and i386. I recall seeing a use after
free time bug with FreeBSD 8 and a Drake Skinny card with WITNESS
and INVARIANTS on.
First task is get all of the new structures to be named in FreeBSD
style format.
Next is probably to deal with the 64bit addressing changes that are
mostly around the #ifdef __amd64__ checks.
Thanks to LSI for providing the initial code.
Obtained from: LSI
replace amd(4) with the former in the amd64, i386 and pc98 GENERIC kernel
configuration files. Besides duplicating functionality, amd(4), which
previously also supported the AMD Am53C974, unlike esp(4) is no longer
maintained and has accumulated enough bit rot over time to always cause
a panic during boot as long as at least one target is attached to it
(see PR 124667).
PR: 124667
Obtained from: NetBSD (based on)
MFC after: 3 days
take advantage of it instead of duplicating it. This reduces the size of
the i386 GENERIC kernel by about 4k. The only potential in-tree user left
unconverted is xe(4), which generally should be changed to use miibus(4)
instead of implementing PHY handling on its own, as otherwise it makes not
much sense to add a dependency on miibus(4)/mii_bitbang(4) to xe(4) just
for the MII bitbang'ing code. The common MII bitbang'ing code also is
useful in the embedded space for using GPIO pins to implement MII access.
- Based on lessons learnt with dc(4) (see r185750), add bus barriers to the
MII bitbang read and write functions of the other drivers converted in
order to ensure the intended ordering. Given that register access via an
index register as well as register bank/window switching is subject to the
same problem, also add bus barriers to the respective functions of smc(4),
tl(4) and xl(4).
- Sprinkle some const.
Thanks to the following testers:
Andrew Bliznak (nge(4)), nwhitehorn@ (bm(4)), yongari@ (sis(4) and ste(4))
Thanks to Hans-Joerg Sirtl for supplying hardware to test stge(4).
Reviewed by: yongari (subset of drivers)
Obtained from: NetBSD (partially)
drivers that only ever attach to a particular MAC driver, i.e. inphy(4),
ruephy(4) and xlphy(4), to the directory where the respective MAC driver
lives and only compile it into the kernel when the latter is also there,
also removing it from miibus.ko and moving it into the module of the
respective MAC driver.
- While at it, rename exphy.c, which comes from NetBSD where the MAC driver
it corresponds to also is named ex(4) instead of xl(4) but that in FreeBSD
actually identifies itself as xlphy(4), and its function names accordingly
for consistency.
- Additionally while at it, fix some minor style issues like whitespace
in the register headers and add multi-inclusion protection to inphyreg.h.
thanks for their contiued support to FreeBSD.
This is version 10.80.00.003 from codeset 10.2.1 [1]
Obtained from: LSI http://kb.lsi.com/Download16574.aspx [1]
build the ip_fw_pfil.c hooks and ipfw even in case of no-ip under the
assumption that the private L2 hook (which hopefully eventually will be a
pfil hook as well) can still be useful.
Allow building the module without inet as well.
Glanced at by: jhb
MFC after: 3 days
build it with and without INET/INET6 support.
Submitted by: Alexander V. Chernikov <melifaro at yandex-team.ru> [1]
Tested by: Alexander V. Chernikov <melifaro at yandex-team.ru> [1]
Approved by: re (bz)
MFC after: 2 weeks
options defined in the kernel config. This more closely matches the
behavior of other modules which inherit configuration settings from the
kernel configuration during a kernel + modules build.
Reviewed by: luigi
Approved by: re (kib)
MFC after: 1 week
improvements:
(1) Implement new model in previously missed at91 UART driver
(2) Move BREAK_TO_DEBUGGER and ALT_BREAK_TO_DEBUGGER from opt_comconsole.h
to opt_kdb.h (spotted by np)
(3) Garbage collect now-unused opt_comconsole.h
MFC after: 3 weeks
Approved by: re (bz)
(1) opt_capsicum.h is no longer required in ffs_alloc.c, so remove the
#include.
(2) portalfs depends on opt_capsicum.h, so have the Makefile generate one
if required.
These affect only modules built without a kernel (i.e, not buildkernel,
but yes buildworld if the dubious MODULES_WITH_WORLD is used).
Approved by: re (bz)
Sponsored by: Google Inc
the NFS subsystems use five of the rpcsec_gss/kgssapi entry points,
but since it was not obvious which others might be useful, all
nineteen were included. Basically the nineteen entry points are
set in a structure called rpc_gss_entries and inline functions
defined in sys/rpc/rpcsec_gss.h check for the entry points being
non-NULL and then call them. A default value is returned otherwise.
Requested by rwatson.
Reviewed by: jhb
MFC after: 2 weeks
cloned from the old NFS client, plus additions for NFSv4. A
review of this code is in progress, however it was felt by the
reviewer that it could go in now, before code slush. Any changes
required by the review can be committed as bug fixes later.
This is in no way a complete DFS/radar detection implementation!
It merely creates an abstracted interface which allows for future
development of the DFS radar detection code.
Note: Net80211 already handles the bulk of the DFS machinery,
all we need to do here is figure out that a radar event has occured
and inform it as such. It then drives the DFS state engine for us.
The "null" DFS radar detection module is included by default;
it doesn't require a device line.
This commit:
* Adds a simple abstracted layer for radar detection state -
sys/dev/ath/ath_dfs/;
* Implements a null DFS module which doesn't do anything;
(ie, implements the exact behaviour at the moment);
* Adds hooks to the ath driver to process received radar events
and gives the DFS module a chance to determine whether
a radar has been detected.
Obtained from: Atheros
filters working. (All other filters - switch without L2 info rewrite,
steer, and drop - were already fully-functional).
Some contrived examples of "switch" filters with L2 rewriting:
# cxgbetool t4nex0 iport 0 dport 80 action switch vlan +9 eport 3
Intercept all packets received on physical port 0 with TCP port 80 as
destination, insert a vlan tag with VID 9, and send them out of port 3.
# cxgbetool t4nex0 sip 192.168.1.1/32 ivlan 5 action switch \
vlan =9 smac aa:bb:cc:dd:ee:ff eport 0
Intercept all packets (received on any port) with source IP address
192.168.1.1 and VLAN id 5, rewrite the VLAN id to 9, rewrite source mac
to aa:bb:cc:dd:ee:ff, and send it out of port 0.
MFC after: 1 week
This branch is now considered frozen: future bhyve development will take
place in a branch off -CURRENT.
sys/dev/bvm/bvm_console.c
sys/dev/bvm/bvm_dbg.c
- simple console driver/gdb debug port used for bringup. supported
by user-space bhyve executable
sys/conf/options.amd64
sys/amd64/amd64/minidump_machdep.c
- allow NKPT to be set in the kernel config file
sys/amd64/conf/GENERIC
- mptable config options; bhyve user-space executable creates an mptable
with number of CPUs, and optional vendor extension
- add bvm console/debug
- set NKPT to 512 to allow loading of large RAM disks from the loader
- include kdb/gdb
sys/amd64/amd64/local_apic.c
sys/amd64/amd64/apic_vector.S
sys/amd64/include/specialreg.h
- if x2apic mode available, use MSRs to access the local APIC, otherwise
fall back to 'classic' MMIO mode
sys/amd64/amd64/mp_machdep.c
- support AP spinup on CPU models that don't have real-mode support by
overwriting the real-mode page with a message that supplies the bhyve
user-space executable with enough information to start the AP directly
in 64-bit mode.
sys/amd64/amd64/vm_machdep.c
- insert pause statements into cpu shutdown busy-wait loops
sys/dev/blackhole/blackhole.c
sys/modules/blackhole/Makefile
- boot-time loadable module that claims all PCI bus/slot/funcs specified
in an env var that are to be used for PCI passthrough
sys/amd64/amd64/intr_machdep.c
- allow round-robin assignment of device interrupts to CPUs to be disabled
from the loader
sys/amd64/include/bus.h
- convert string ins/outs instructions to loops of individual in/out since
bhyve doesn't support these yet
sys/kern/subr_bus.c
- if the device was no created with a fixed devclass, then remove it's
association with the devclass it was associated with during probe.
Otherwise, new drivers do not get a chance to probe/attach since the
device will stay married to the first driver that it probed successfully
but failed to attach.
Sponsored by: NetApp, Inc.
Some files keep the SUN4V tags as a code reference, for the future,
if any rewamped sun4v support wants to be added again.
Reviewed by: marius
Tested by: sbruno
Approved by: re
vmm.ko - kernel module for VT-x, VT-d and hypervisor control
bhyve - user-space sequencer and i/o emulation
vmmctl - dump of hypervisor register state
libvmm - front-end to vmm.ko chardev interface
bhyve was designed and implemented by Neel Natu.
Thanks to the following folk from NetApp who helped to make this available:
Joe CaraDonna
Peter Snyder
Jeff Heller
Sandeep Mann
Steve Miller
Brian Pawlowski
Reference code that shows how to get a packet's timestamp out of
cxgbe(4). Disabled by default because we don't have a standard way
today to pass this information up the stack.
The timestamp is 60 bits wide and each increment represents 1 tick of
the T4's core clock. As an example, the timestamp granularity is ~4.4ns
for this card:
# sysctl dev.t4nex.0.core_clock
dev.t4nex.0.core_clock: 228125
MFC after: 1 week
(reporting IFM_LOOP based on BMCR_LOOP is left in place though as
it might provide useful for debugging). For most mii(4) drivers it
was unclear whether the PHYs driven by them actually support
loopback or not. Moreover, typically loopback mode also needs to
be activated on the MAC, which none of the Ethernet drivers using
mii(4) implements. Given that loopback media has no real use (and
obviously hardly had a chance to actually work) besides for driver
development (which just loopback mode should be sufficient for
though, i.e one doesn't necessary need support for loopback media)
support for it is just dropped as both NetBSD and OpenBSD already
did quite some time ago.
- Let mii_phy_add_media() also announce the support of IFM_NONE.
- Restructure the PHY entry points to use a structure of entry points
instead of discrete function pointers, and extend this to include
a "reset" entry point. Make sure any PHY-specific reset routine is
always used, and provide one for lxtphy(4) which disables MII
interrupts (as is done for a few other PHYs we have drivers for).
This includes changing NIC drivers which previously just called the
generic mii_phy_reset() to now actually call the PHY-specific reset
routine, which might be crucial in some cases. While at it, the
redundant checks in these NIC drivers for mii->mii_instance not being
zero before calling the reset routines were removed because as soon
as one PHY driver attaches mii->mii_instance is incremented and we
hardly can end up in their media change callbacks etc if no PHY driver
has attached as mii_attach() would have failed in that case and not
attach a miibus(4) instance.
Consequently, NIC drivers now no longer should call mii_phy_reset()
directly, so it was removed from EXPORT_SYMS.
- Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe().
The purpose of that function is to perform the common steps to attach
a PHY driver instance and to hook it up to the miibus(4) instance and to
optionally also handle the probing, addition and initialization of the
supported media. So all a PHY driver without any special requirements
has to do in its bus attach method is to call mii_phy_dev_attach()
along with PHY-specific MIIF_* flags, a pointer to its PHY functions
and the add_media set to one. All PHY drivers were updated to take
advantage of mii_phy_dev_attach() as appropriate. Along with these
changes the capability mask was added to the mii_softc structure so
PHY drivers taking advantage of mii_phy_dev_attach() but still
handling media on their own do not need to fiddle with the MII attach
arguments anyway.
- Keep track of the PHY offset in the mii_softc structure. This is done
for compatibility with NetBSD/OpenBSD.
- Keep track of the PHY's OUI, model and revision in the mii_softc
structure. Several PHY drivers require this information also after
attaching and previously had to wrap their own softc around mii_softc.
NetBSD/OpenBSD also keep track of the model and revision on their
mii_softc structure. All PHY drivers were updated to take advantage
as appropriate.
- Convert the mebers of the MII data structure to unsigned where
appropriate. This is partly inspired by NetBSD/OpenBSD.
- According to IEEE 802.3-2002 the bits actually have to be reversed
when mapping an OUI to the MII ID registers. All PHY drivers and
miidevs where changed as necessary. Actually this now again allows to
largely share miidevs with NetBSD, which fixed this problem already
9 years ago. Consequently miidevs was synced as far as possible.
- Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that
weren't explicitly converted to support flow control before. It's
unclear whether flow control actually works with these but typically
it should and their net behavior should be more correct with these
changes in place than without if the MAC driver sets MIIF_DOPAUSE.
Obtained from: NetBSD (partially)
Reviewed by: yongari (earlier version), silence on arch@ and net@
- 77115: Implement support for O_DIRECT.
- 98425: Fix a performance issue introduced in 70131 that was causing
reads before writes even when writing full blocks.
- 98658: Rename the BALLOC flags from B_* to BA_* to avoid confusion with
the struct buf B_ flags.
- 100344: Merge the BA_ and IO_ flags so so that they may both be used in
the same flags word. This merger is possible by assigning the IO_ flags
to the low sixteen bits and the BA_ flags the high sixteen bits.
- 105422: Fix a file-rewrite performance case.
- 129545: Implement IO_INVAL in VOP_WRITE() by marking the buffer as
"no cache".
- Readd the DOINGASYNC() macro and use it to control asynchronous writes.
Change i-node updates to honor DOINGASYNC() instead of always being
synchronous.
- Use a PRIV_VFS_RETAINSUGID check instead of checking cr_uid against 0
directly when deciding whether or not to clear suid and sgid bits.
Submitted by: Pedro F. Giffuni giffunip at yahoo
The AR9130 is an AR9160/AR5416 family WMAC which is glued directly
to the AR913x SoC peripheral bus (APB) rather than via a PCI/PCIe
bridge.
The specifics:
* A new build option is required to use the AR9130 - AH_SUPPORT_AR9130.
This is needed due to the different location the RTC registers live
with this chip; hopefully this will be undone in the future.
This does currently mean that enabling this option will break non-AR9130
builds, so don't enable it unless you're specifically building an image
for the AR913x SoC.
* Add the new probe, attach, EEPROM and PLL methods specific to Howl.
* Add a work-around to ah_eeprom_v14.c which disables some of the checks
for endian-ness and magic in the EEPROM image if an eepromdata block
is provided. This'll be fixed at a later stage by porting the ath9k
probe code and making sure it doesn't break in other setups (which
my previous attempt at this did.)
* Sprinkle Howl modifications throughput the interrupt path - it doesn't
implement the SYNC interrupt registers, so ignore those.
* Sprinkle Howl chip powerup/down throughout the reset path; the RTC methods
were
* Sprinkle some other Howl workarounds in the reset path.
* Hard-code an alternative setup for the AR_CFG register for Howl, that
sets up things suitable for Big-Endian MIPS (which is the only platform
this chip is glued to.)
This has been tested on the AR913x based TP-Link WR-1043nd mode, in
legacy, HT/20 and HT/40 modes.
Caveats:
* 2ghz has only been tested. I've not seen any 5ghz radios glued to this
chipset so I can't test it.
* AR5416_INTERRUPT_MITIGATION is not supported on the AR9130. At least,
it isn't implemented in ath9k. Please don't enable this.
* This hasn't been tested in MBSS mode or in RX/TX block-aggregation mode.
device in /dev/ create symbolic link with adY name, trying to mimic old ATA
numbering. Imitation is not complete, but should be enough in most cases to
mount file systems without touching /etc/fstab.
- To know what behavior to mimic, restore ATA_STATIC_ID option in cases
where it was present before.
- Add some more details to UPDATING.
set the f_flags field of "struct statfs". This had the interesting
effect of making the NFSv4 mounts "disappear" after r221014,
since NFSMNT_NFSV4 and MNT_IGNORE became the same bit.
Move the files used for a diskless NFS root from sys/nfsclient
to sys/nfs in preparation for them to be used by both NFS
clients. Also, move the declaration of the three global data
structures from sys/nfsclient/nfs_vfsops.c to sys/nfs/nfs_diskless.c
so that they are defined when either client uses them.
Reviewed by: jhb
MFC after: 2 weeks
create reasonably large cache for the keys that is filled when
needed. The previous version was problematic for very large providers
(hundreds of terabytes or serval petabytes). Every terabyte of data
needs around 256kB for keys. Make the default cache limit big enough
to fit all the keys needed for 4TB providers, which will eat at most
1MB of memory.
MFC after: 2 weeks
In particular:
- implement compat shims for old stat(2) variants and ogetdirentries(2);
- implement delivery of signals with ancient stack frame layout and
corresponding sigreturn(2);
- implement old getpagesize(2);
- provide a user-mode trampoline and LDT call gate for lcall $7,$0;
- port a.out image activator and connect it to the build as a module
on amd64.
The changes are hidden under COMPAT_43.
MFC after: 1 month
Introduce the AHB glue for Atheros embedded systems. Right now it's
hard-coded for the AR9130 chip whose support isn't yet in this HAL;
it'll be added in a subsequent commit.
Kernel configuration files now need both 'ath' and 'ath_pci' devices; both
modules need to be loaded for the ath device to work.
Add new RAID GEOM class, that is going to replace ataraid(4) in supporting
various BIOS-based software RAIDs. Unlike ataraid(4) this implementation
does not depend on legacy ata(4) subsystem and can be used with any disk
drivers, including new CAM-based ones (ahci(4), siis(4), mvs(4), ata(4)
with `options ATA_CAM`). To make code more readable and extensible, this
implementation follows modular design, including core part and two sets
of modules, implementing support for different metadata formats and RAID
levels.
Support for such popular metadata formats is now implemented:
Intel, JMicron, NVIDIA, Promise (also used by AMD/ATI) and SiliconImage.
Such RAID levels are now supported:
RAID0, RAID1, RAID1E, RAID10, SINGLE, CONCAT.
For any all of these RAID levels and metadata formats this class supports
full cycle of volume operations: reading, writing, creation, deletion,
disk removal and insertion, rebuilding, dirty shutdown detection
and resynchronization, bad sector recovery, faulty disks tracking,
hot-spare disks. For Intel and Promise formats there is support multiple
volumes per disk set.
Look graid(8) manual page for additional details.
Co-authored by: imp
Sponsored by: Cisco Systems, Inc. and iXsystems, Inc.
