This is a significant rewrite of much of the previous driver; lots of
misc. cleanup was also performed, and support for a few other minor
features was also added.
Partial support for the EVENT_IDX feature was added a while ago,
but this commit adds an interface for the device driver to hint
how long (in terms of descriptors) the next interrupt should be
delayed.
The first user of this will be used to reduce VirtIO net's Tx
completion interrupts.
The consequence of the bug is that fini calls are not done
when a slab is freed by a call-back from the page daemon.
It went unnoticed for two months because fini is little used.
I spotted the bug while reading the code to learn how it works
so I could write it up for the next edition of the Design and
Implementation of FreeBSD book.
No MFC needed as this code exists only in HEAD.
Reviewed by: kib, jeff
Tested by: pho
for ARM.
This is quite ugly, because it has to work around a clang bug that does not
allow built-in functions to be defined, even when they're ones that are
expected to be built as part of a library.
Reviewed by: ed
This is a nice small outdoor/indoor AP from Ubiquity Networks.
The device has:
AR7241 CPU SoC
AR9287 Wifi
8MB flash
32MB RAM
wifi has been tested to work along with leds.
Submitted by: loos
Approved by: sbruno (mentor, implicit)
Tested by: hiren
priority. If the write is requested by a system daemon, sleeping
there would starve resources and cause deadlock.
Reported and tested by: pho
Sponsored by: The FreeBSD Foundation
A warning is emitted again if the temperature became briefly valid
meanwhile. This avoids spamming the user when the sensor is broken.
Other values (ie. not _TMP) always raise a warning.
is not giving us a 100% success rate. Bump the delay to 200ms as
that seems to do the trick.
Note that during testing the delay was added to uart_bus_attach()
in uart_core.c. While having the delay in a different place can
change the behaviour, it was not expected. Having to bump the
delay with another 50ms could therefore be an indication that
the problem can not be solved with delays.
Reported by: kevlo@
Tested by: kevlo@
Intel CPUs. The feature tags TLB entries with the Id of the address
space and allows to avoid TLB invalidation on the context switch, it
is available only in the long mode. In the microbenchmarks, using the
PCID decreased latency of the context switches by ~30% on SandyBridge
class desktop CPUs, measured with the lat_ctx program from lmbench.
If available, use INVPCID instruction when a TLB entry in non-current
address space needs to be invalidated. The instruction is typically
available on the Haswell.
If needed, the use of PCID can be turned off with the
vm.pmap.pcid_enabled loader tunable set to 0. The state of the
feature is reported by the vm.pmap.pcid_enabled sysctl. The sysctl
vm.pmap.pcid_save_cnt reports the number of context switches which
avoided invalidating the TLB; compare with the total number of context
switches, available as sysctl vm.stats.sys.v_swtch.
Sponsored by: The FreeBSD Foundation
Reviewed by: alc
Tested by: pho, bf
- Allow the Rx/Tx queue sizes to be configured by tunables
- Bail out earlier if the Tx queue unlikely has enough free
descriptors to hold the frame
- Cleanup some of the offloading capabilities handling
value. Some hosts do not publish "extended" disk IDs via virtual-device in
an attempt to avoid confusing old blkfront drivers, and without this change
we failed to attach such disks.
In particular, this commit allows all 24 ephemeral disks on EC2 hs1.8xlarge
instances to be used, instead of only the first 15.
MFC after: 3 days
cards.
This is a T4 and T5 chip feature which lets the chip deliver multiple
Ethernet frames in a single buffer. This is more efficient within the
chip, in the driver, and reduces wastage of space in rx buffers.
- Always allocate rx buffers from the jumbop zone, no matter what the
MTU is. Do not use the normal cluster refcounting mechanism.
- Reserve space for an mbuf and a refcount in the cluster itself and let
the chip DMA multiple frames in the rest.
- Use the embedded mbuf for the first frame and allocate mbufs on the
fly for any additional frames delivered in the cluster. Each of these
mbufs has a reference on the underlying cluster.
refcount. This one is willing to work with buffers that may already be
referenced. MEXTADD/m_extadd are suitable only for the first attachment
to a cluster -- they initialize the refcount to 1.
Use this new driver for both PV and HVM instances.
This driver requires a Xen hypervisor that supports vector callbacks,
VCPUOP hypercalls, and reports that it has a "safe PV clock".
New timer driver:
Submitted by: will
Sponsored by: Spectra Logic Corporation
PV port to new driver, and bug fixes:
Submitted by: Roger Pau Monné
Sponsored by: Citrix Systems R&D
sys/dev/xen/timer/timer.c:
- Register a PV timer device driver which (currently)
implements device_{identify,probe,attach} and stubs
device_detach. The detach routine requires functionality
not provided by timecounters(4). The suspend and resume
routines need additional work (due to Xen requiring that
the hypercalls be executed on the target VCPU), and aren't
needed for our purposes.
- Make sure there can only be one device instance of this
driver, and that it only registers one eventtimers(4) and
one timecounters(4) device interface. Make both interfaces
use PCPU data as needed.
- Match, with a few style cleanups & API differences, the
Xen versions of the "fetch time" functions.
- Document the magic scale_delta() better for the i386 version.
- When registering the event timer, bind a separate event
channel for the timer VIRQ to the device's event timer
interrupt handler for each active VCPU. Describe each
interrupt as "xen_et:c%d", so they can be identified per
CPU in "vmstat -i" or "show intrcnt" in KDB.
- When scheduling a timer into the hypervisor, try up to
60 times if the hypervisor rejects the time as being in
the past. In the common case, this retry shouldn't happen,
and if it does, it should only happen once. This is
because the event timer advertises a minimum period of
100usec, which is only less than the usual hypercall round
trip time about 1 out of every 100 tries. (Unlike other
similar drivers, this one actually checks whether the
hypervisor accepted the singleshot timer set hypercall.)
- Implement a RTC PV clock based on the hypervisor wallclock.
sys/conf/files:
- Add dev/xen/timer/timer.c if the kernel configuration
includes either the XEN or XENHVM options.
sys/conf/files.i386:
sys/i386/include/xen/xen_clock_util.h:
sys/i386/xen/clock.c:
sys/i386/xen/xen_clock_util.c:
sys/i386/xen/mp_machdep.c:
sys/i386/xen/xen_rtc.c:
- Remove previous PV timer used in i386 XEN PV kernels, the
new timer introduced in this change is used instead (so
we share the same code between PVHVM and PV).
MFC after: 2 weeks
to 15 minutes, and 5 minutes for things like READ ELEMENT STATUS.
This is needed to account for the worst case scenarios on at least
some Spectra Logic tape libraries.
Sponsored by: Spectra Logic
MFC after: 3 days
Re-structure Xen HVM support so that:
- Xen is detected and hypercalls can be performed very
early in system startup.
- Xen interrupt services are implemented using FreeBSD's native
interrupt delivery infrastructure.
- the Xen interrupt service implementation is shared between PV
and HVM guests.
- Xen interrupt handlers can optionally use a filter handler
in order to avoid the overhead of dispatch to an interrupt
thread.
- interrupt load can be distributed among all available CPUs.
- the overhead of accessing the emulated local and I/O apics
on HVM is removed for event channel port events.
- a similar optimization can eventually, and fairly easily,
be used to optimize MSI.
Early Xen detection, HVM refactoring, PVHVM interrupt infrastructure,
and misc Xen cleanups:
Sponsored by: Spectra Logic Corporation
Unification of PV & HVM interrupt infrastructure, bug fixes,
and misc Xen cleanups:
Submitted by: Roger Pau Monné
Sponsored by: Citrix Systems R&D
sys/x86/x86/local_apic.c:
sys/amd64/include/apicvar.h:
sys/i386/include/apicvar.h:
sys/amd64/amd64/apic_vector.S:
sys/i386/i386/apic_vector.s:
sys/amd64/amd64/machdep.c:
sys/i386/i386/machdep.c:
sys/i386/xen/exception.s:
sys/x86/include/segments.h:
Reserve IDT vector 0x93 for the Xen event channel upcall
interrupt handler. On Hypervisors that support the direct
vector callback feature, we can request that this vector be
called directly by an injected HVM interrupt event, instead
of a simulated PCI interrupt on the Xen platform PCI device.
This avoids all of the overhead of dealing with the emulated
I/O APIC and local APIC. It also means that the Hypervisor
can inject these events on any CPU, allowing upcalls for
different ports to be handled in parallel.
sys/amd64/amd64/mp_machdep.c:
sys/i386/i386/mp_machdep.c:
Map Xen per-vcpu area during AP startup.
sys/amd64/include/intr_machdep.h:
sys/i386/include/intr_machdep.h:
Increase the FreeBSD IRQ vector table to include space
for event channel interrupt sources.
sys/amd64/include/pcpu.h:
sys/i386/include/pcpu.h:
Remove Xen HVM per-cpu variable data. These fields are now
allocated via the dynamic per-cpu scheme. See xen_intr.c
for details.
sys/amd64/include/xen/hypercall.h:
sys/dev/xen/blkback/blkback.c:
sys/i386/include/xen/xenvar.h:
sys/i386/xen/clock.c:
sys/i386/xen/xen_machdep.c:
sys/xen/gnttab.c:
Prefer FreeBSD primatives to Linux ones in Xen support code.
sys/amd64/include/xen/xen-os.h:
sys/i386/include/xen/xen-os.h:
sys/xen/xen-os.h:
sys/dev/xen/balloon/balloon.c:
sys/dev/xen/blkback/blkback.c:
sys/dev/xen/blkfront/blkfront.c:
sys/dev/xen/console/xencons_ring.c:
sys/dev/xen/control/control.c:
sys/dev/xen/netback/netback.c:
sys/dev/xen/netfront/netfront.c:
sys/dev/xen/xenpci/xenpci.c:
sys/i386/i386/machdep.c:
sys/i386/include/pmap.h:
sys/i386/include/xen/xenfunc.h:
sys/i386/isa/npx.c:
sys/i386/xen/clock.c:
sys/i386/xen/mp_machdep.c:
sys/i386/xen/mptable.c:
sys/i386/xen/xen_clock_util.c:
sys/i386/xen/xen_machdep.c:
sys/i386/xen/xen_rtc.c:
sys/xen/evtchn/evtchn_dev.c:
sys/xen/features.c:
sys/xen/gnttab.c:
sys/xen/gnttab.h:
sys/xen/hvm.h:
sys/xen/xenbus/xenbus.c:
sys/xen/xenbus/xenbus_if.m:
sys/xen/xenbus/xenbusb_front.c:
sys/xen/xenbus/xenbusvar.h:
sys/xen/xenstore/xenstore.c:
sys/xen/xenstore/xenstore_dev.c:
sys/xen/xenstore/xenstorevar.h:
Pull common Xen OS support functions/settings into xen/xen-os.h.
sys/amd64/include/xen/xen-os.h:
sys/i386/include/xen/xen-os.h:
sys/xen/xen-os.h:
Remove constants, macros, and functions unused in FreeBSD's Xen
support.
sys/xen/xen-os.h:
sys/i386/xen/xen_machdep.c:
sys/x86/xen/hvm.c:
Introduce new functions xen_domain(), xen_pv_domain(), and
xen_hvm_domain(). These are used in favor of #ifdefs so that
FreeBSD can dynamically detect and adapt to the presence of
a hypervisor. The goal is to have an HVM optimized GENERIC,
but more is necessary before this is possible.
sys/amd64/amd64/machdep.c:
sys/dev/xen/xenpci/xenpcivar.h:
sys/dev/xen/xenpci/xenpci.c:
sys/x86/xen/hvm.c:
sys/sys/kernel.h:
Refactor magic ioport, Hypercall table and Hypervisor shared
information page setup, and move it to a dedicated HVM support
module.
HVM mode initialization is now triggered during the
SI_SUB_HYPERVISOR phase of system startup. This currently
occurs just after the kernel VM is fully setup which is
just enough infrastructure to allow the hypercall table
and shared info page to be properly mapped.
sys/xen/hvm.h:
sys/x86/xen/hvm.c:
Add definitions and a method for configuring Hypervisor event
delievery via a direct vector callback.
sys/amd64/include/xen/xen-os.h:
sys/x86/xen/hvm.c:
sys/conf/files:
sys/conf/files.amd64:
sys/conf/files.i386:
Adjust kernel build to reflect the refactoring of early
Xen startup code and Xen interrupt services.
sys/dev/xen/blkback/blkback.c:
sys/dev/xen/blkfront/blkfront.c:
sys/dev/xen/blkfront/block.h:
sys/dev/xen/control/control.c:
sys/dev/xen/evtchn/evtchn_dev.c:
sys/dev/xen/netback/netback.c:
sys/dev/xen/netfront/netfront.c:
sys/xen/xenstore/xenstore.c:
sys/xen/evtchn/evtchn_dev.c:
sys/dev/xen/console/console.c:
sys/dev/xen/console/xencons_ring.c
Adjust drivers to use new xen_intr_*() API.
sys/dev/xen/blkback/blkback.c:
Since blkback defers all event handling to a taskqueue,
convert this task queue to a "fast" taskqueue, and schedule
it via an interrupt filter. This avoids an unnecessary
ithread context switch.
sys/xen/xenstore/xenstore.c:
The xenstore driver is MPSAFE. Indicate as much when
registering its interrupt handler.
sys/xen/xenbus/xenbus.c:
sys/xen/xenbus/xenbusvar.h:
Remove unused event channel APIs.
sys/xen/evtchn.h:
Remove all kernel Xen interrupt service API definitions
from this file. It is now only used for structure and
ioctl definitions related to the event channel userland
device driver.
Update the definitions in this file to match those from
NetBSD. Implementing this interface will be necessary for
Dom0 support.
sys/xen/evtchn/evtchnvar.h:
Add a header file for implemenation internal APIs related
to managing event channels event delivery. This is used
to allow, for example, the event channel userland device
driver to access low-level routines that typical kernel
consumers of event channel services should never access.
sys/xen/interface/event_channel.h:
sys/xen/xen_intr.h:
Standardize on the evtchn_port_t type for referring to
an event channel port id. In order to prevent low-level
event channel APIs from leaking to kernel consumers who
should not have access to this data, the type is defined
twice: Once in the Xen provided event_channel.h, and again
in xen/xen_intr.h. The double declaration is protected by
__XEN_EVTCHN_PORT_DEFINED__ to ensure it is never declared
twice within a given compilation unit.
sys/xen/xen_intr.h:
sys/xen/evtchn/evtchn.c:
sys/x86/xen/xen_intr.c:
sys/dev/xen/xenpci/evtchn.c:
sys/dev/xen/xenpci/xenpcivar.h:
New implementation of Xen interrupt services. This is
similar in many respects to the i386 PV implementation with
the exception that events for bound to event channel ports
(i.e. not IPI, virtual IRQ, or physical IRQ) are further
optimized to avoid mask/unmask operations that aren't
necessary for these edge triggered events.
Stubs exist for supporting physical IRQ binding, but will
need additional work before this implementation can be
fully shared between PV and HVM.
sys/amd64/amd64/mp_machdep.c:
sys/i386/i386/mp_machdep.c:
sys/i386/xen/mp_machdep.c
sys/x86/xen/hvm.c:
Add support for placing vcpu_info into an arbritary memory
page instead of using HYPERVISOR_shared_info->vcpu_info.
This allows the creation of domains with more than 32 vcpus.
sys/i386/i386/machdep.c:
sys/i386/xen/clock.c:
sys/i386/xen/xen_machdep.c:
sys/i386/xen/exception.s:
Add support for new event channle implementation.
- Relax atomic_read() and atomic_set() macros. Linux does not require any
memory barrier. Also, these macros may be even reordered or optimized away
according to the API documentation:
https://www.kernel.org/doc/Documentation/atomic_ops.txt
We've been seeing lots of cache line contention (but not lock contention!)
in our workloads between the various TX and RX threads going on.
The write lock is only grabbed when configuration changes are made - which
are infrequent.
With this patch, the contention and cycles spent waiting for updates
disappear.
Sponsored by: Netflix, Inc.
- Remove excessive parenthesis
- Use KNF continuation indentation
- Cut down on excessive continuation lines
- More consistent style in messages
- Use uprintf() instead of printf()
Submitted by: bde
calls ns8250_bus_ipend() almost immediately after ns8250_bus_attach().
As it appears, a line break condition is being signalled for almost
all received characters due to this. A delay of 150ms seems enough
to allow the H/W to settle and to avoid the problem.
More analysis is needed, but for now a regression has been addressed.
Reported by: kevlo@
Tested by: kevlo@
MADV_DONTNEED) and madvise(..., MADV_FREE). Specifically, introduce a new
pmap function, pmap_advise(), that operates on a range of virtual addresses
within the specified pmap, allowing for a more efficient implementation of
MADV_DONTNEED and MADV_FREE. Previously, the implementation of
MADV_DONTNEED and MADV_FREE relied on per-page pmap operations, such as
pmap_clear_reference(). Intuitively, the problem with this implementation
is that the pmap-level locks are acquired and released and the page table
traversed repeatedly, once for each resident page in the range
that was specified to madvise(2). A more subtle flaw with the previous
implementation is that pmap_clear_reference() would clear the reference bit
on all mappings to the specified page, not just the mapping in the range
specified to madvise(2).
Since our malloc(3) makes heavy use of madvise(2), this change can have a
measureable impact. For example, the system time for completing a parallel
"buildworld" on a 6-core amd64 machine was reduced by about 1.5% to 2.0%.
Note: This change only contains pmap_advise() implementations for a subset
of our supported architectures. I will commit implementations for the
remaining architectures after further testing. For now, a stub function is
sufficient because of the advisory nature of pmap_advise().
Discussed with: jeff, jhb, kib
Tested by: pho (i386), marcel (ia64)
Sponsored by: EMC / Isilon Storage Division
(re)start the interface when it is down. This change fix a race with
BOOTP where the response packet is lost because the interface is being
reset by a netmask change right after send the packet.
PR: 178318
Approved by: adrian (mentor)
Add a last-modified timestamp to each LRO entry and provide an interface
to flush all inactive entries. Drivers decide when to flush and what
the inactivity threshold should be.
Network drivers that process an rx queue to completion can enter a
livelock type situation when the rate at which packets are received
reaches equilibrium with the rate at which the rx thread is processing
them. When this happens the final LRO flush (normally when the rx
routine is done) does not occur. Pure ACKs and segments with total
payload < 64K can get stuck in an LRO entry. Symptoms are that TCP
tx-mostly connections' performance falls off a cliff during heavy,
unrelated rx on the interface.
Flushing only inactive LRO entries works better than any of these
alternates that I tried:
- don't LRO pure ACKs
- flush _all_ LRO entries periodically (every 'x' microseconds or every
'y' descriptors)
- stop rx processing in the driver periodically and schedule remaining
work for later.
Reviewed by: andre
UF_SYSTEM, UF_SPARSE, UF_OFFLINE, UF_REPARSE, UF_ARCHIVE, UF_READONLY,
and UF_HIDDEN.
Sort the file flags tmpfs supports alphabetically. tmpfs now
supports the same flags as UFS, with the exception of SF_SNAPSHOT.
Reported by: bdrewery, antoine
Sponsored by: Spectra Logic
- tom_uninit had to be reworked not to hold the adapter lock (a mutex)
around t4_deactivate_uld, which acquires the uld_list_lock.
- the ifc_match for the interface cloner that creates the tracer ifnet
had to be reworked as the kernel calls ifc_match with the global
if_cloners_mtx held.
allocations under low free-space conditions (-r254995), determine
that old block-preference search order used before -r249782 worked
a bit better. This change reverts to that block-preference search order.
MFC after: 2 weeks
I have 25TB Dell PERC 6 RAID5 array. When it becomes almost
full (10-20GB free), processes which write data to it start
eating 100% CPU and write speed drops below 1MB/sec (normally
to gives 400MB/sec). The revision at which it first became
apparent was http://svnweb.freebsd.org/changeset/base/249782.
The offending change reserved an area in each cylinder group to
store metadata. The new algorithm attempts to save this area for
metadata and allows its use for non-metadata only after all the
data areas have been exhausted. The size of the reserved area
defaults to half of minfree, so the filesystem reports full before
the data area can completely fill. However, in this report, the
filesystem has had minfree reduced to 1% thus forcing the metadata
area to be used for data. As the filesystem approached full, it
had only metadata areas left to allocate. The result was that
every block allocation had to scan summary data for 30,000 cylinder
groups before falling back to searching up to 30,000 metadata areas.
The fix is to give up on saving the metadata areas once the free
space reserve drops below 2%. The effect of this change is to use
the old algorithm of just accepting the first available block that
we find. Since most filesystems use the default 5% minfree, this
will have no effect on their operation. For those that want to push
to the limit, they will get their crappy block placements quickly.
Submitted by: Dmitry Sivachenko
Fix Tested by: Dmitry Sivachenko
PR: kern/181226
MFC after: 2 weeks
the passed vnode belongs to the same mount point (v_vfsp or also
known as v_mount in FreeBSD). This check prevents the code from
proceeding further on vnodes that do not belong to ZFS, for
instance, on UFS or NULLFS.
The recent change (merged as r254585) on upstream changes the
check of v_vfsp to instead check the znode's z_zfsvfs. On Illumos
this would work because when the vnode comes from lofs, the
VOP_REALVP() would give the right vnode, this is not true on
FreeBSD where our VOP_REALVP is a no-op, and as such tdvp is
not guaranteed to be a ZFS vnode, and will later trigger a
failed assertion when verifying the vnode.
This changeset modifies our local shims (zfs_freebsd_rename and
zfs_freebsd_link) to check if v_mount matches before proceeding
further.
Reported by: many
Diagnostic work by: avg
problems with the way MLEN, MHLEN, and struct mbuf are set up.
CTASSERT's are provided to detect such issues at compile time in the
future.
The #define MLEN and MHLEN calculation do not take actual compiler-
induced alignment and padding inside the complete struct mbuf into
account. Accordingly appropriate attention is required when changing
members of struct mbuf.
Ideally one would calculate MLEN as (MSIZE - sizeof(((struct mbuf *)0)->m_hdr)
but that doesn't work as the compiler refuses to operate on an as of
yet incomplete structure.
In particular ARM 32bit has more strict alignment requirements which
caused 4 bytes of padding between m_hdr and pkthdr in struct mbuf
because of the 64bit members in pkthdr. This wasn't picked up by MLEN
and MHLEN causing an overflow of the mbuf provided data storage by
overestimating its size.
I386 didn't show this problem because it handles unaligned access just
fine, albeit at a small performance penalty.
On 64bit architectures the struct mbuf layout is 64bit aligned in all
places.
Reported by: Thomas Skibo <ThomasSkibo-at-sbcglobal-dot-net>
Tested by: tuexen, ian, Thomas Skibo (extended patch)
Sponsored by: The FreeBSD Foundation
notify (enable spinup) required", instead of doing the normal
retries, poll for a change in status.
We will poll every half second for a minute for the status to
change.
Hitachi drives (and likely other SAS drives) return that ASC/ASCQ
when they are waiting to spin up. What it means is that they are
waiting for the SAS expander to send them the SAS
NOTIFY (ENABLE SPINUP) primitive.
That primitive is the mechanism expanders/enclosures use to
sequence drive spinup to avoid overloading power supplies.
Sponsored by: Spectra Logic
MFC after: 3 days
The aim of this function is to eventually be the completion entry point
for all 802.11 encapsulated mbufs. All the wifi drivers end up doing
what is in this function so it's an easy win to turn it into a net80211
method and abstract out this code.
Ideally the drivers will all eventually be modified to queue up completed
mbufs and call this function with all the driver locks not held.
This will allow for some much more interesting software queue handling
in the future (like net80211 based A-MSDU, fast-frames, A-MPDU aggregation
and retransmission.)
Tested:
* ath(4), iwn(4)
- Use queue size fields from the Tx/Rx queues in various places
instead of (currently the same values) from the softc.
- Fix potential crash in detach if the attached failed to alloc
queue memory.
- Move the VMXNET3_MAX_RX_SEGS define to a better spot.
- Tweak frame size calculation w.r.t. ETHER_ALIGN. This could be
tweaked some more, or removed since it probably doesn't matter
much for x86 (and the x86 class of machines this driver will
be used on).
- Route PCI interrupt for NIC
- Make "no mapping" warning more user-friendly: add device name and mention
that it's IRQ mapping
- Do not overlap ICUs' IO window with PCI devices' IO windows by starting
IO rman at offset 0x100
for the available pbuf when passed vnode is backing md(4). Other i/o
directed to the same md device might already hold pbufs, and then we
could deadlock since only our progress can free a pbuf needed for
wakeup.
Obtained from: projects/vm6
Reminded and tested by: pho
MFC after: 1 week
ps(1) utility, e.g. "ps -O fib".
bin/ps/keyword.c:
Add the "fib" keyword and default its column name to "FIB".
bin/ps/ps.1:
Add "fib" as a supported keyword.
sys/compat/freebsd32/freebsd32.h:
sys/kern/kern_proc.c:
sys/sys/user.h:
Add the default fib number for a process (p->p_fibnum)
to the user land accessible process data of struct kinfo_proc.
Submitted by: Oliver Fromme <olli@fromme.com>, gibbs
and add support for default underride to $loader_version, acting as a way to
name a release. Release text is not displayed for the aforementioned feature
of alternate display layout (introduced in r254237); however, for all other
layouts (incl. default), the release name is displayed at lower-right.
See version.4th(8) for additional information and/or historical details.
NOTE: Also a minor edit to version.4th(8) while we're here.
It is needed for fdread(1) in order to be able to recover from CRC
errors in the data field of a floppy sector (by returning the sector
data that failed CRC, rather than inventing dummy data).
When closing the device, clear all transient device options.
MFC after: 1 week
Promoting base pages to superpages can increase TLB coverage and allow for
efficient use of page table entries. This development provides FreeBSD/ARM
with superpages management mechanism roughly equivalent to what we have for
i386 and amd64 architectures.
1. Add mechanism for automatic promotion of 4KB page mappings to 1MB section
mappings (and demotion when not needed, respectively).
2. Managed and non-kernel mappings are now superpages-aware.
3. The functionality can be enabled by setting "vm.pmap.sp_enabled" tunable to
a non-zero value (either in loader.conf or by modifying "sp_enabled"
variable in pmap-v6.c file). By default, automatic promotion is currently
disabled.
Submitted by: Zbigniew Bodek <zbb@semihalf.com>
Reviewed by: alc
Sponsored by: The FreeBSD Foundation, Semihalf
This allows for enabling and configuring superpages reservation mechanism in
order to allocate and populate 256 4KB base pages (for the purpose of
promotion to a 1MB superpage).
Submitted by: Zbigniew Bodek <zbb@semihalf.com>
Reviewed by: alc
Sponsored by: The FreeBSD Foundation, Semihalf
dynamic translation so that their arguments match the definitions for
these providers in Solaris and illumos. Thus, existing scripts for these
providers should work unmodified on FreeBSD.
Tested by: gnn, hiren
MFC after: 1 month
The FFLAGS and OFLAGS now work correctly also for files opened with O_EXEC.
Except possibly fuse, the other users pass values without O_EXEC set. fuse
appears to assume O_EXEC is handled correctly.
Although F_SETFL may not be commonly used for execute-only file descriptors,
F_GETFL may be useful to find the access mode.
This driver is based on Linux 3.8 and a previous effort by kan@.
More informations about this project can be found on the FreeBSD wiki:
https://wiki.freebsd.org/AMD_GPU
The driver is split into:
sys/dev/drm2:
The driver sources.
sys/modules/drm2/radeonkmw:
The driver main kernel module's Makefile.
sys/modules/drm2/radeonkmsfw:
All firmware kernel module Makefiles. There's one directory and one
Makefile for each firmware.
sys/contrib/dev/drm2/radeonkmsfw:
All firmware binary sources.
tools/tools/drm/radeon
Tools to update firmwares or regenerate some headers.
Merging the driver to FreeBSD 9.x may be possible but not a priority for
now.
Help from: kib@, kan@
Tested by: avg@, kwm@, ray@,
Alexander Yerenkow <yerenkow@gmail.com>,
Anders Bolt-Evensen <andersbo87@me.com>,
Denis Djubajlo <stdedjub@googlemail.com>,
J.R. Oldroyd <fbsd@opal.com>,
Mikaël Urankar <mikael.urankar@gmail.com>,
Pierre-Emmanuel Pédron <pepcitron@gmail.com>,
Sam Fourman Jr. <sfourman@gmail.com>,
Wade <wade-is-great@live.com>,
(probably other I forgot...)
HW donations: kyzh, Yakaz
Here are two new functions to map and unmap the Video BIOS:
void * vga_pci_map_bios(device_t dev, size_t *size);
void vga_pci_unmap_bios(device_t dev, void *bios);
The BIOS is either taken from the shadow copy made by the System BIOS at
boot time if the given device was used for the default display (i386,
amd64 and ia64 only), or from the PCI expansion ROM.
Additionally, one can determine if a given device was the default
display at boot time using the following new function:
void vga_pci_unmap_bios(device_t dev, void *bios);
Add a new ttm_bo_release_mmap() function to unmap pages in a
vm_object_t. Pages are freed when the buffer object is later released.
This function is called in ttm_bo_unmap_virtual_locked(), replacing
Linux' unmap_mapping_range(). In particular this is called when a buffer
object is about to be moved, so that its mapping is invalidated.
However, we don't use this function in ttm_bo_vm_dtor(), because the
vm_object_t is already marked as OBJ_DEAD and the pages will be
unmapped.
Approved by: kib@
This fixes a crash where a SIGLALRM, heavily used by X.Org, would
interrupt the wait, causing the page fault to fail and the "Xorg"
process to receive a SIGSEGV.
Approved by: kib@
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Jan 14 15:08:14 2013 +0100
drm/ttm: fix fence locking in ttm_buffer_object_transfer, 2nd try
This fixes up
commit e8e89622ed361c46bf90ba4828e685a8b603f7e5
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Dec 18 22:25:11 2012 +0100
drm/ttm: fix fence locking in ttm_buffer_object_transfer
which leaves behind a might_sleep in atomic context, since the
fence_lock spinlock is held over a kmalloc(GFP_KERNEL) call. The fix
is to revert the above commit and only take the lock where we need it,
around the call to ->sync_obj_ref.
v2: Fixup things noticed by Maarten Lankhorst:
- Brown paper bag locking bug.
- No need for kzalloc if we clear the entire thing on the next line.
- check for bo->sync_obj (totally unlikely race, but still someone
else could have snuck in) and clear fbo->sync_obj if it's cleared
already.
Reported-by: Dave Airlie <airlied@gmail.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Approved by: kib@
Author: Dave Airlie <airlied@gmail.com>
Date: Wed Jan 16 15:58:34 2013 +1000
ttm: on move memory failure don't leave a node dangling
if we have a move notify callback, when moving fails, we call move notify
the opposite way around, however this ends up with *mem containing the mm_node
from the bo, which means we double free it. This is a follow on to the previous
fix.
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Approved by: kib@
Author: Dave Airlie <airlied@gmail.com>
Date: Wed Jan 16 14:25:44 2013 +1000
ttm: don't destroy old mm_node on memcpy failure
When we are using memcpy to move objects around, and we fail to memcpy
due to lack of memory to populate or failure to finish the copy, we don't
want to destroy the mm_node that has been copied into old_copy.
While working on a new kms driver that uses memcpy, if I overallocated bo's
up to the memory limits, and eviction failed, then machine would oops soon
after due to having an active bo with an already freed drm_mm embedded in it,
freeing it a second time didn't end well.
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Approved by: kib@
Author: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Date: Tue Jan 15 14:57:28 2013 +0100
drm/ttm: unexport ttm_bo_wait_unreserved
All legitimate users of this function outside ttm_bo.c are gone, now
it's only an implementation detail.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Approved by: kib@
Author: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Date: Tue Jan 15 14:57:10 2013 +0100
drm/ttm: use ttm_bo_reserve_slowpath_nolru in ttm_eu_reserve_buffers, v2
This requires re-use of the seqno, which increases fairness slightly.
Instead of spinning with a new seqno every time we keep the current one,
but still drop all other reservations we hold. Only when we succeed,
we try to get back our other reservations again.
This should increase fairness slightly as well.
Changes since v1:
- Increase val_seq before calling ttm_bo_reserve_slowpath_nolru and
retrying to take all entries to prevent a race.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Approved by: kib@
Author: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Date: Tue Jan 15 14:57:05 2013 +0100
drm/ttm: add ttm_bo_reserve_slowpath
Instead of dropping everything, waiting for the bo to be unreserved
and trying over, a better strategy would be to do a blocking wait.
This can be mapped a lot better to a mutex_lock-like call.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Approved by: kib@
Author: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Date: Tue Jan 15 14:56:48 2013 +0100
drm/ttm: cleanup ttm_eu_reserve_buffers handling
With the lru lock no longer required for protecting reservations we
can just do a ttm_bo_reserve_nolru on -EBUSY, and handle all errors
in a single path.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Author: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Date: Tue Jan 15 14:56:37 2013 +0100
drm/ttm: remove lru_lock around ttm_bo_reserve
There should no longer be assumptions that reserve will always succeed
with the lru lock held, so we can safely break the whole atomic
reserve/lru thing. As a bonus this fixes most lockdep annotations for
reservations.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Some of the FreeBSD-specific definitions are moved to drm_os_freebsd.h.
But there's still work to do to clean it up and reduce the diff with
Linux' drmP.h.
The SDM (June 2013) tables on these are rather confusing. Yes, they
assign the same name (BR_MISP_RETIRED.ALL_BRANCHES) to two codes
(C5H/00H and C5H/04H.) The latter however is the PEBS version.
So, to make it easier to see the difference - and yes, we can use
both without having to actually enable the PEBS specific bits! -
just rename the PEBS one to _PS so there's no clashing.
Tested:
* Sandy bridge
This header can be easily updated using the new "gen-drm_pciids" script,
available in tools/tools/drm. The script uses the Linux' drm_pciids.h
header for new IDs, the FreeBSD's one because we add the name of the
device to each IDs, and the PCI IDs database (misc/pciids port) to fill
this name automatically for new IDS.
To call the script:
tools/tools/drm/gen-drm_pciids \
/path/to/linux/drm_pciids.h \
/path/to/freebsd/drm_pciids.h \
/path/to/pciids/pci.ids
external mbuf buffer management capabilities in the future.
For now only EXT_FREE_OK is defined with current legacy behavior.
Sponsored by: The FreeBSD Foundation
