Without this change, if one had a swap-on-mirror configuration, gmirror
will rebuild mirror component(s) on boot, because they are dirty (they
were open on shutdown).
complete backout as the ntpd_sync_on_start etc/rc.conf tunable is still
present, though the default is now NO (was YES). Since we're no longer
syncing time at startup by default when ntpd is enabled (as was the case
24hrs ago), remove UPDATING entry pointing out that ntpd(1) -g is slower
than ntpdate(1).
Hopefully ntpd_sync_on_start="YES" can be made the default for -CURRENT
after 5.3 is cut. At the very least, this should be set to YES when a
user requests to have ntpd enabled via sysinstall(1).
Requested by: many
calls to ntpd -g. ntpd is noticeably slower than ntpdate, but is also more
accurate. This removes the nasty hackery in rc.d/ntpdate that would parse
out ntp servers from /etc/ntp.conf (ntpd knows how to read its own config
file). By default, ntpd *will* sync with its listed time servers. To
turn this off so that ntpd does not sync, ntpd_sync_on_start="NO" can be
added to /etc/rc.conf. If ntpd is not enabled (the default), then time is
not synced on startup. ntpdate has been depreciated by the ntpd authors
for quite some time so this change shouldn't be unexpected.
Suggested by: des
Approved by: roberto (resident ntp guru)
calls to ntpd -g. ntpd is noticably slower than ntpdate, but is also more
accurate. This removes the nasty hackery in rc.d/ntpdate that would parse
out ntp servers from /etc/ntp.conf (ntpd knows how to read its own config
file). By default, ntpd *will* sync with its listed time servers. To
turn this off so that ntpd does not sync, ntpd_sync_on_start="NO" can be
added to /etc/rc.conf. If ntpd is not enabled (the default), then time is
not synced on startup. ntpdate's use has been depreciated by the ntpd
authors for quite some time so this change shouldn't be unexpected.
Suggested by: des
Approved by: roberto (resident ntp guru)
- Add OpenBSD example rulesets as advertised in etc/pf.conf and pf.conf(5)
- Tweak the pointer to fit the FreeBSD default location share/examples/pf
- Account for the new directory in BSD.usr.dist (no hier(7) change required
as share/examples is an opaque item there).
Obtained from: OpenBSD
Reminded by: Thomas T. Veldhouse
PR: docs/71691
MFC after: 2 days
VT6122 gigabit ethernet chip and integrated 10/100/1000 copper PHY.
The vge driver has been added to GENERIC for i386, pc98 and amd64,
but not to sparc or ia64 since I don't have the ability to test
it there. The vge(4) driver supports VLANs, checksum offload and
jumbo frames.
Also added the lge(4) and nge(4) drivers to GENERIC for i386 and
pc98 since I was in the neighborhood. There's no reason to leave them
out anymore.
part of the pf module.
While here fix a comment that was c'n'ped from rc.d/pf
PR: bin/71096 (partly)
Submitted by: Ville-Pertti Keinonen
MFC after: 2 days
from list_net_interfaces() when network_interfaces=auto.
Rationale: Since the auto case is special, the lesser evil
had to be chosen among not adding cloned interfaces to
_tmplist or removing duplicates from _tmplist after adding
cloned interfaces. Since list_net_interfaces() must not use
/usr/bin tools, the former "evil" appeared clearer and much
more efficient. (See the PR audit trail for discussion.)
PR: conf/63700
Reviewed by: brooks
MFC after: 5 days
the submit and outbound daemon, else if sendmail_submit_enable=yes, don't
start the outbound daemon. Only one daemon should be started.
Also, do not rebuild database maps at boot time. The code didn't pay
attention to SENDMAIL_MAP_TYPE and assumed 'hash'. Also, admins may
not want maps automatically rebuilt just because the back end database
has changed. Finally, some maps are built with mode tools than just
makemap (e.g., using cidrexpand on the access text file before sending
it to makemap).
Noticed by: ache
Reviewed by: ache
so reflect this in the default. The uucp uid is a bit funny, and
is used by mtree in /var/spool for locks, so we can't remove it
without thinking about it a bit harder.
than one interface from the command line:
# /etc/rc.d/netif start bfe0 xl0
It's also possible to restart an interface(s):
# /etc/rc.d/netif restart bfe0
This required some changes to rc.subr(8) so that if the start/stop commands
are overidden the rest of the command line (after the start/stop/etc... cmd)
is passed through to the subroutines.
o Separate out local (ports) scripts that use rc.d, and the old style
startup/shutdown scripts and execute them separately. On startup the
rc.d style scripts are executed first and then the old-style scripts.
On shutdown, exactly the reverse happens.
o The rc.d ports scripts should now behave more like base system scripts.
Scripts ending in .sh will be sourced into the current shell, while the
rest will be executed in a subshell. Previously, all ports scripts,
regardless of the .sh suffix, were executed in a subshell.
o The parent script, /etc/rc.d/localpkg, passes its command line arguments
straight to the rc.d ports scripts. This means they should now honor
faststop and faststart commands as well. Old style scripts, should not see
any differences. They will still get either a start or stop command.
o The initial phrase shown during shutdown has been changed to use
"local packages" instead of "daemon processes" to be more inline with the
phrase used during local package startup. The phrases are also used only for
old-style ports script startup/shutdown, whereas previously they were being
used for both rc.d and old-style scripts. This should make startup/shutdown
output a bit less ugly.
Discussed with: portmgr
Has Reservations: eik
- Ask the user up to X times (3 by default) for the pass-phrase, if
it is incorrect the first time.
- Add support for storing the lockfiles in another other directory
than /etc.
- Document that it is possible to override the location of each single
lockfile.
Approved by: pjd
if [ -z "${_rc_subr_loaded}" ]; then
_rc_subr_loaded="YES"
...
fi
in order to avoid re-interpreting rc.subr every time an rc.d
script is run. In my tests, this speeds up rc time by about
8-10%.
