Summary:
The hardware does not expose a classic SMBus interface.
Instead it has a lower level interface that can express a far richer
I2C protocol than what smbus offers. However, the interface does not
provide a way to explicitly generate the I2C stop and start conditions.
It's only possible to request that the stop condition is generated
after transferring the next byte in either direction. So, at least
one data byte must always be transferred.
Thus, some I2C sequences are impossible to generate, e.g., an equivalent
of smbus quick command (<start>-<slave addr>-<r/w bit>-<stop>).
At the same time isl(4) and cyapa(4) are moved to iicbus and now they use
iicbus_transfer for communication. Previously they used smbus_trans()
interface that is not defined by the SMBus protocol and was implemented
only by ig4(4). In fact, that interface was impossible to implement
for the typical SMBus controllers like intpm(4) or ichsmb(4) where
a type of the SMBus command must be programmed.
The plan is to remove smbus_trans() and all its uses.
As an aside, the smbus_trans() method deviates from the standard,
but perhaps backwards, FreeBSD convention of using 8-bit slave
addresses (shifted by 1 bit to the left). The method expects
7-bit addresses.
There is a user facing consequence of this change.
A user must now provide device hints for isl and cyapa that specify an iicbus to use
and a slave address on it.
On Chromebook hardware where isl and cyapa devices are commonly found
it is also possible to use a new chromebook_platform(4) driver that
automatically configures isl and cyapa devices. There is no need to
provide the device hints in that case,
Right now smbus(4) driver tries to discover all slaves on the bus.
That is very dangerous. Fortunately, the probing code uses smbus_trans()
to do its job, so it is really enabled for ig4 only.
The plan is to remove that auto-probing code and smbus_trans().
Tested by: grembo, Matthias Apitz <guru@unixarea.de> (w/o
chromebook_platform)
Discussed with: grembo, imp
Reviewed by: wblock (docs)
MFC after: 1 month
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D8172
these show a 9-10% reduction in user and system time for a buildworld -j48.
Obtained from: ABT Systems Ltd
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
The driver currently supports chips that are fully compliant with the
JEDEC SPD / EEPROM / TS standard (JEDEC Standard 21-C,
TSE2002 Specification, frequenlty referred to as JEDEC JC 42.4).
Additionally some chips from STMicroelectronics are supported as well.
They are compliant except for their Device ID pattern.
Given the continued lack of any common sensor infrastructure, the driver
uses an ad-hoc sysctl to report the temperature.
Reviewed by: wblock (documentation)
MFC after: 2 weeks
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D8174
Summary:
The Freescale e500v2 PowerPC core does not use a standard FPU.
Instead, it uses a Signal Processing Engine (SPE)--a DSP-style vector processor
unit, which doubles as a FPU. The PowerPC SPE ABI is incompatible with the
stock powerpc ABI, so a new MACHINE_ARCH was created to deal with this.
Additionaly, the SPE opcodes overlap with Altivec, so these are mutually
exclusive. Taking advantage of this fact, a new file, powerpc/booke/spe.c, was
created with the same function set as in powerpc/powerpc/altivec.c, so it
becomes effectively a drop-in replacement. setjmp/longjmp were modified to save
the upper 32-bits of the now-64-bit GPRs (upper 32-bits are only accessible by
the SPE).
Note: This does _not_ support the SPE in the e500v1, as the e500v1 SPE does not
support double-precision floating point.
Also, without a new MACHINE_ARCH it would be impossible to provide binary
packages which utilize the SPE.
Additionally, no work has been done to support ports, work is needed for this.
This also means no newer gcc can yet be used. However, gcc's powerpc support
has been refactored which would make adding a powerpcspe-freebsd target very
easy.
Test Plan:
This was lightly tested on a RouterBoard RB800 and an AmigaOne A1222
(P1022-based) board, compiled against the new ABI. Base system utilities
(/bin/sh, /bin/ls, etc) still function appropriately, the system is able to boot
multiuser.
Reviewed By: bdrewery, imp
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D5683
The exported functions will be used by
Alpine Ethernet driver.
Obtained from: Semihalf
Submitted by: Michal Stanek <mst@semihalf.com>
Sponsored by: Annapurna Labs
Reviewed by: wma
Differential Revision: https://reviews.freebsd.org/D7763
This patch adds support for MSI-X interrupts
on Annapurna Alpine platform. MSI-X on Alpine
work similarly to GICv2m, i.e. some range of
SPI interrupts is reserved in GIC and individual
SPIs can be triggered by MSI-X messages.
This SPI range is defined in FDT.
Obtained from: Semihalf
Submitted by: Michal Stanek <mst@semihalf.com>
Sponsored by: Annapurna Labs
Reviewed by: nwhitehorn, wma
Differential Revision: https://reviews.freebsd.org/D7579
All devices:
- add support for rate adaptation via ieee80211_amrr(9);
- use short preamble for transmitted frames when needed;
- multi-bss support:
* for RTL8821AU: 2 VAPs at the same time;
* other: 1 any VAP + 1 sta VAP.
RTL8188CE:
- fix IQ calibration bug (reason of significant speed degradation);
- add h/w crypto acceleration support.
USB:
- A-MPDU Tx support;
- short GI support;
Other:
- add support for RTL8812AU / RTL8821AU chipsets
(a/b/g/n only; no ac yet);
- split merged code into subparts:
* bus glue (usb/*, pci/*, rtl*/usb/*, rtl*/pci/*)
* common (if_rtwn*)
* chip-specific (rtl*/*)
- various other bugfixes.
Due to code reorganization, module names / requirements were changed too:
urtwn urtwnfw -> rtwn rtwn_usb rtwnfw
rtwn rtwnfw -> rtwn rtwn_pci rtwnfw
Tested with RTL8188CE, RTL8188CUS, RTL8188EU and RTL8821AU.
Tested by: kevlo, garga,
Peter Garshtja <peter.garshtja@ambient-md.com>,
Kevin McAleavey <kevin.mcaleavey@knosproject.com>,
Ilias-Dimitrios Vrachnis <id@vrachnis.com>,
<otacilio.neto@bsd.com.br>
Relnotes: yes
This commit, long overdue, contains contributions in the last 2 years
from Stefano Garzarella, Giuseppe Lettieri, Vincenzo Maffione, including:
+ fixes on monitor ports
+ the 'ptnet' virtual device driver, and ptnetmap backend, for
high speed virtual passthrough on VMs (bhyve fixes in an upcoming commit)
+ improved emulated netmap mode
+ more robust error handling
+ removal of stale code
+ various fixes to code and documentation (some mixup between RX and TX
parameters, and private and public variables)
We also include an additional tool, nmreplay, which is functionally
equivalent to tcpreplay but operating on netmap ports.
- Rename SOC_BCM2837 to SOC_BRCM_BCM2837, put it to opt_soc.h
- do not use files.XXX files, just move required sources to
conf/files.arm64 and make them depend on soc_brcm_bcm2837
Suggested by: andrew
RPI3 kernel config builds kernel compatible with latest upstream device
tree and firmware: https://github.com/raspberrypi/firmware/tree/master/boot
As of today it's 597c662a613df1144a6bc43e5f4505d83bd748ca
Default console is PL01x, so pi3-disable-bt dt overlay should be configured
in config.txt and stock U-Boot should be patched to use proper serial port.
Yet unsupported: SMP, VCHIQ, RNG driver. RNG requires some work due to
upstream device tree incompatibility.
Multiple people contributed to this work over time: db@, loos@, manu@
to add actions that run when a TCP frame is sent or received on a TCP
session in the ESTABLISHED state. In the base tree, this functionality is
only used for the h_ertt module, which is used by the cc_cdg, cc_chd, cc_hd,
and cc_vegas congestion control modules.
Presently, we incur overhead to check for hooks each time a TCP frame is
sent or received on an ESTABLISHED TCP session.
This change adds a new compile-time option (TCP_HHOOK) to determine whether
to include the hhook(9) framework for TCP. To retain backwards
compatibility, I added the TCP_HHOOK option to every configuration file that
already defined "options INET". (Therefore, this patch introduces no
functional change. In order to see a functional difference, you need to
compile a custom kernel without the TCP_HHOOK option.) This change will
allow users to easily exclude this functionality from their kernel, should
they wish to do so.
Note that any users who use a custom kernel configuration and use one of the
congestion control modules listed above will need to add the TCP_HHOOK
option to their kernel configuration.
Reviewed by: rrs, lstewart, hiren (previous version), sjg (makefiles only)
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D8185
userland. It supports userland interfaces to UEFI Runtime Services. This is
indended to the the MI portion of EFI RuntimeServices support.
Differential Revision: https://reviews.freebsd.org/D8128
Reviewed by: kib@, wblock@, Ganael Laplanche
for later Cortex-A CPUs that support the Multiprocessor Extensions. This
will be needed to support both in a single GENERIC kernel while still
being able to only build for a single SoC.
Reviewed by: mmel
Relnotes: yes
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D8138
- Convert "options EVDEV" to "device evdev" and "device uinput", add
modules for both new devices. They are isolated subsystems and do not
require any compile-time changes to general kernel subsytems
- For hybrid drivers that have evdev as an optional way to deliver input
events add option EVDEV_SUPPORT. Update all existing hybrid drivers
to use it instead of EVDEV
- Remove no-op DECLARE_MODULE in evdev, it's not required, MODULE_VERSION
is enough
- Add evdev module dependency to uinput
Submitted by: Vladimir Kondratiev <wulf@cicgroup.ru>
like other PCI network drivers. The sys/ofed directory is now mainly
reserved for generic infiniband code, with exception of the mthca driver.
- Add new manual page, mlx4en(4), describing how to configure and load
mlx4en.
- All relevant driver C-files are now prefixed mlx4, mlx4_en and
mlx4_ib respectivly to avoid object filename collisions when compiling
the kernel. This also fixes an issue with proper dependency file
generation for the C-files in question.
- Device mlxen is now device mlx4en and depends on device mlx4, see
mlx4en(4). Only the network device name remains unchanged.
- The mlx4 and mlx4en modules are now built by default on i386 and
amd64 targets. Only building the mlx4ib module depends on
WITH_OFED=YES .
Sponsored by: Mellanox Technologies
- The original 'disengage' ATA controller model does not work properly
for all possible disk configurations. Use the newly added ATA disk
veto eventhandler to fit into all possible disk configuration.
- If the 'invalid LUN' happens on blkvsc controllers, return
CAM_DEV_NOT_THERE so that CAM will not destroy attached disks under
the blkvsc controllers.
Submitted by: Hongjiang Zhang <honzhan microsoft com>
Discussed with: mav
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7693
Summary:
This enables some features of the DIU, using a static configuration,
specified either via a 'edid' property on the 'display' FDT node, or a
'video-mode' environment variable (bootarg). 'video-mode' was chosen because it
matches u-boot's naming, so it can be set with:
setenv bootargs video-mode=${video-mode}
at the u-boot CLI.
Mouse cursor is not supported currently, as a hardware cursor is not supported
by framebuffer VT yet. Currently it only supports a 32bpp ARGB (actually BGRA)
format, and only a single composite plane, at up to 1280x1024.
Differential Revision: https://reviews.freebsd.org/D8022
build can break when different source files create the same target
files (case-insensitivity speaking). This is the case for object
files compiled with -fpic and shared libraries. The former uses
an extension of ".So", and the latter an extension ".so". Rename
shared object files from *.So to *.pico to match what NetBSD does.
See also r305855
MFC after: 1 month
Sponsored by: Bracket Computing
Differential Revision: https://reviews.freebsd.org/D7906
Runtime services require special execution environment for the call.
Besides that, OS must inform firmware about runtime virtual memory map
which will be active during the calls, with the SetVirtualAddressMap()
runtime call, done while the 1:1 mapping is still used. There are two
complication: the SetVirtualAddressMap() effectively must be done from
loader, which needs to know kernel address map in advance. More,
despite not explicitely mentioned in the specification, both 1:1 and
the map passed to SetVirtualAddressMap() must be active during the
SetVirtualAddressMap() call. Second, there are buggy BIOSes which
require both mappings active during runtime calls as well, most likely
because they fail to identify all relocations to perform.
On amd64, we can get rid of both problems by providing 1:1 mapping for
the duration of runtime calls, by temprorary remapping user addresses.
As result, we avoid the need for loader to know about future kernel
address map, and avoid bugs in BIOSes. Typically BIOS only maps
something in low 4G. If not runtime bugs, we would take advantage of
the DMAP, as previous versions of this patch did.
Similar but more complicated trick can be used even for i386 and 32bit
runtime, if and when the EFI boot on i386 is supported. We would need
a trampoline page, since potentially whole 4G of VA would be switched
on calls, instead of only userspace portion on amd64.
Context switches are disabled for the duration of the call, FPU access
is granted, and interrupts are not disabled. The later is possible
because kernel is mapped during calls.
To test, the sysctl mib debug.efi_time is provided, setting it to 1
makes one call to EFI get_time() runtime service, on success the efitm
structure is printed to the control terminal. Load efirt.ko, or add
EFIRT option to the kernel config, to enable code.
Discussed with: emaste, imp
Tested by: emaste (mac, qemu)
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
There is nothing CPU specific here, and it's usable by both fdt and Open
Firmware based systems. Rather than keeping the same file in every one, just
add it to the ofw/fdt block in the main file.
This is in preparation for linking with LLVM's lld, which does not have
a compiled-in default output emulation. lld requires that it is
specified via the -m option, or obtained from the object file(s) being
linked.
This will also allow all build targets to share a common linker binary.
Reviewed by: imp
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D7837
In order to make CloudABI work on ARMv6, start off by copying over the
sysvec for ARM64 and adjust it to use 32-bit registers. Also add code
for fetching arguments from the stack if needed, as there are fewer
register than on ARM64.
Also import the vDSO that is needed to invoke system calls. This vDSO
uses the intra procedure call register (ip) to store the system call
number. This is a bit simpler than what native FreeBSD does, as FreeBSD
uses r7, while preserving the original r7 into ip.
This sysvec seems to be complete enough to start CloudABI processes.
These processes are capable of linking in the vDSO and are therefore
capable of executing (most?) system calls successfully. Unfortunately,
the biggest show stopper is still that TLS is completely broken:
- The linker used by CloudABI, LLD, still has troubles with some of the
relocations needed for TLS. See LLVM bug 30218 for more details.
- Whereas FreeBSD uses the tpidruro register for TLS, for CloudABI I
want to make use of tpidrurw, so that userspace can modify the base
address directly. This is needed for efficient emulation.
Unfortunately, this register doesn't seem to be preserved across
context switches yet.
Obtained from: https://github.com/NuxiNL/cloudabi (the vDSO)
evdev is a generic input event interface compatible with Linux
evdev API at ioctl level. It allows using unmodified (apart from
header name) input evdev drivers in Xorg, Wayland, Qt.
This commit has only generic kernel API. evdev support for individual
hardware drivers like ukbd, ums, atkbd, etc. will be committed later.
Project was started by Jakub Klama as part of GSoC 2014. Jakub's
evdev implementation was later used as a base, updated and finished
by Vladimir Kondratiev.
Submitted by: Vladimir Kondratiev <wulf@cicgroup.ru>
Reviewed by: adrian, hans
Differential Revision: https://reviews.freebsd.org/D6998
The cxgbev/cxlv driver supports Virtual Function devices for Chelsio
T4 and T4 adapters. The VF devices share most of their code with the
existing PF4 driver (cxgbe/cxl) and as such the VF device driver
currently depends on the PF4 driver.
Similar to the cxgbe/cxl drivers, the VF driver includes a t4vf/t5vf
PCI device driver that attaches to the VF device. It then creates
child cxgbev/cxlv devices representing ports assigned to the VF.
By default, the PF driver assigns a single port to each VF.
t4vf_hw.c contains VF-specific routines from the shared code used to
fetch VF-specific parameters from the firmware.
t4_vf.c contains the VF-specific PCI device driver and includes its
own attach routine.
VF devices are required to use a different firmware request when
transmitting packets (which in turn requires a different CPL message
to encapsulate messages). This alternate firmware request does not
permit chaining multiple packets in a single message, so each packet
results in a firmware request. In addition, the different CPL message
requires more detailed information when enabling hardware checksums,
so parse_pkt() on VF devices must examine L2 and L3 headers for all
packets (not just TSO packets) for VF devices. Finally, L2 checksums
on non-UDP/non-TCP packets do not work reliably (the firmware trashes
the IPv4 fragment field), so IPv4 checksums for such packets are
calculated in software.
Most of the other changes in the non-VF-specific code are to expose
various variables and functions private to the PF driver so that they
can be used by the VF driver.
Note that a limited subset of cxgbetool functions are supported on VF
devices including register dumps, scheduler classes, and clearing of
statistics. In addition, TOE is not supported on VF devices, only for
the PF interfaces.
Reviewed by: np
MFC after: 2 months
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7599
This commit adds drivers for Alpine Cache Coherency Unit
and North Bridge Service whose task is to configure
the system fabric and enable cache coherency.
Obtained from: Semihalf
Submitted by: Michal Stanek <mst@semihalf.com>
Sponsored by: Annapurna Labs
Reviewed by: wma
Differential Revision: https://reviews.freebsd.org/D7565
