Minor changes to the network driver. A multiqueue driver that is
a significant rewrite will be in merged shortly.
Contains projects/virtio commits:
r246058:
vtnet: Move an mbuf ASSERT to the calling function
r246059:
vtnet: Tweak ASSERT message
MFC after: 1 month
Contains projects/virtio commits:
r245717:
virtio_balloon: Make the softc lock a regular mutex
r245718:
virtio_balloon: Remove two unuseful ASSERTs
r245719:
virtio_balloon: More verbose ASSERT messages
r245720:
virtio_balloon: Simplify lowmem handling in vtballoon_inflate()
r252530:
virtio_balloon: Use just a kthread instead of dedciated kproc
r252568:
virtio_balloon: Need to use kthread_exit() after r252530
MFC after: 1 month
The notable changes of this commit are support for disk resizing
and chases updates to the spec regarding write caching.
Contains projects/virtio commits:
r245713:
virtio_blk: Replace __FUNCTION__ with __func__
r245714:
virtio_blk: Use more consistent mutex name
r245715:
virtio_blk: Print device name too if failed to reinit during dump
r245716:
virtio_blk: Remove an unuseful ASSERT
r245723:
virtio_blk: Record the vendor and device information
r245724:
virtio_blk: Add resize support
r245726:
virtio_blk: More verbose ASSERT messages
r245730:
virtio_blk: Tweak resize announcement message
r246061:
virtio_blk: Do not always read entire config
r246062:
virtio_blk: Use topology to set the stripe size/offset
r246307:
virtio_blk: Correct stripe offset calculation
r246063:
virtio_blk: Add support for write cache enable feature
r246303:
virtio_blk: Expand a comment
r252529:
virtio_blk: Improve write cache handling
r252681:
virtio_blk: Remove unneeded curly braces
MFC after: 1 month
Contains projects/virtio commits:
r245709:
Each VirtIO device was scheduling its own taskqueue(9) to do the
off-level interrupt handling. ithreads(9) is the more nature way
to do this. The primary motivation for this work to better support
network multiqueue.
r245710:
virtio: Change virtqueue intr handlers to return void
r245711:
virtio_blk: Remove interrupt taskqueue
r245721:
vtnet: Remove interrupt taskqueue
r245722:
virtio_scsi: Remove interrupt taskqueue
r245747:
vtnet: Remove taskqueue fields missed in r245721
MFC after: 1 month
we are probing a PCI-PCI bridge it is because we found one by enumerating
the devices on a PCI bus, so the bridge is definitely present. A few
BIOSes report incorrect status (_STA) for some bridges that claimed they
were not present when in fact they were.
While here, move this check earlier for Host-PCI bridges so attach fails
before doing any work that needs to be torn down.
PR: kern/91594
Tested by: Jack Vogel @ Intel
MFC after: 1 week
While this prevents commands getting stuck forever there is no way to guarantee
that data from the command hasn't been committed to the device.
In addition older mfi firmware has a bug that would cause the controller to
frequently stall IO for over our timeout value, which when combined with
a forced timeout often resulted in panics in UFS; which would otherwise be
avoided when the command eventually completed if left alone.
For reference this timeout issue is resolved in Dell FW package 21.2.1-0000.
Fixed FW package version for none Dell controller will likely vary.
MFC after: 2 days
state. Previously it used to check if controller has sent a
PAUSE frame to the remote peer.
Reported by: David Imhoff via Brad Smith <brad@OpenBSD.org>
Submitted by: davidch (initial version)
Reviewed by: davidch, David Imhoff <dimhoff_devel@xs4all.nl>
This occurs at RX DMA start, even though the RX FIFO has plenty of
space. I'll go figure out why, but this shouldn't cause people to
be spammed by these messages.
bug where a PCI device would be powered down if it failed to probe, but
not when its driver was detached (e.g. via kldunload).
- Add a new helper method resource_list_release_active() which forcefully
releases any active resources of a specified type from a resource list.
- Add a bus_child_detached method for the PCI bus driver which forces any
active resources to be released (and whines to the console if it finds
any) and then powers the device down.
- Call pci_child_detached() if we fail to probe a device when a driver
is kldloaded. This isn't perfect but can avoid leaking resources
from a probe() routine in the kldload case.
Reviewed by: imp, brooks
MFC after: 1 month
a new firmware command.
NVMe controllers may support up to 7 firmware slots for storing of
different firmware revisions. This new firmware command supports
firmware replacement (i.e. firmware download) with or without immediate
activation, or activation of a previously stored firmware image. It
also supports selection of the firmware slot during replacement
operations, using IDENTIFY information from the controller to
check that the specified slot is valid.
Newly activated firmware does not take effect until the new controller
reset, either via a reboot or separate 'nvmecontrol reset' command to the
same controller.
Submitted by: Joe Golio <joseph.golio@emc.com>
Obtained from: EMC / Isilon Storage Division
MFC after: 3 days
max transfer size. This guards against rogue commands coming in from
userspace.
Also add KASSERTS for the virtual address and unmapped bio cases, if the
transfer size exceeds the controller's max transfer size.
Sponsored by: Intel
MFC after: 3 days
Also allow admin commands to transfer up to this maximum I/O size, rather
than the artificial limit previously imposed. The larger I/O size is very
beneficial for upcoming firmware download support. This has the added
benefit of simplifying the code since both admin and I/O commands now use
the same maximum I/O size.
Sponsored by: Intel
MFC after: 3 days
by treating it as UDMA.
This fixes a problem introduced in r249933/r249939, where CAM sends
ATA_DSM_TRIM to SATA devices using ATA_PASSTHROUGH_16. scsi_ata_trim()
sets protocol as DMA (not UDMA) which is for multi-word DMA, even
though no such mode is selected for the device. isci(4) would fail
these commands which is the correct behavior but not consistent with
other HBAs, namely LSI's.
smh@ did some further testing on an LSI controller, which rejected
ATA_PASSTHROUGH_16 commands with mode=UDMA_OUT, even though only
a UDMA mode was selected on the device. So this precludes adding
any kind of mode detection in CAM to determine which mode to use on
a per-device basis.
Sponsored by: Intel
Discussed with: scottl, smh
Reported by: scottl
Tested by: scottl
MFC after: 3 days
support cache flush and write barrier commands.
sys/dev/xen/blkfront/block.h:
Add per-command flag that specifies that the I/O queue must
be frozen after this command is dispatched. This is used
to implement "single-stepping".
Remove the unused per-command flag that indicates a polled
command.
Add block device instance flags to record backend features.
Add a block device instance flag to indicate the I/O queue
is frozen until all outstanding I/O completes.
Enhance the queue API to allow the number of elements in a
queue to be interrogated.
Prefer "inline" to "__inline".
sys/dev/xen/blkfront/blkfront.c:
Formalize queue freeze semantics by adding methods for both
global and command-associated queue freezing.
Provide mechanism to freeze the I/O queue until all outstanding
I/O completes. Use this to implement barrier semantics
(BIO_ORDERED) when the backend does not support
BLKIF_OP_WRITE_BARRIER commands.
Implement BIO_FLUSH as either a BLKIF_OP_FLUSH_DISKCACHE
command or a 0 byte write barrier. Currently, all publicly
available backends perform a diskcache flush when processing
barrier commands, and this frontend behavior matches what
is done in Linux.
Simplify code by using new queue length API.
Report backend features during device attach and via sysctl.
Submitted by: Roger Pau Monné
Submitted by: gibbs (Merge with new driver queue API, sysctl support)
The AHB code:
* hard coded the AR9130 device id;
* assumes a 4k flash calibration space.
This code now extends this:
* hint.ath.X.eepromsize now overrides the eeprom range, instead of 4k
* hint.ath.X.device_id and hint.ath.X.vendor_id can now be overridden.
Tested:
* AR9330 board (Carambola 2)
one. This change also fixes non-working traffic LED on BCM57780.
Submitted by: Masanobu SAITOH <msaitoh@NetBSD.org>
Tested by: Alexander Milanov <a@amilanov.com>
There are some systems reported, where PCI BAR(5), used for SATA registers
access, is present, but not functional. Attempt to use it brakes devices
detection logic. Try to detect those cases on attach by setting and testing
some bits in SControl register. If bits are unsettable, fallback to legacy
ATA without hot-plug detection, speed control/reporting, etc.
MFC after: 2 weeks
tester of this fix, and realloc_bars breaks some other cases as a small
BAR that is reallocated can end up grabbing space needed by a much larger
BAR in the existing window of a PCI-PCI bridge.
MFC after: 3 days
checksum header. The header contains a received frame length but
the defined length for AX88772B is different with other ASIX
controllers. When the RX checksum is off, AX88772B controller does
not prepend a checksum header so driver has to use normal header
length mask.
This change should fix RX errors when RX checksum offloading is
off.
Tested by: kevlo
MFC After: 1 week
(which should be a PCIE Gen 3 slot for this adapter) by looking back thru the PCI
parent devices to the slot device.
The fix above also corrects the bandwidth display to GT/s rather than the
incorrect Gb/s
Next, allow the use of ALTQ if you select the compile option IXGBE_LEGACY_TX.
Allow the use of 'unsupported' optic modules by a compile option as well.
Add a phy reset capability into the stop code, this is so a static configured
driver will still behave properly when taken down (not being able to unload it).
This revision synchronizes the shared code with Intel internal current code,
and note that it now includes DCB supporting code, this was necessitated by
some internal changes with the code, but it also will provide the opportunity
to develop this feature in the core driver down the road.
I have edited the README to get rid of some of the worse anachronisms in it
as well, its by no means as robust as I might wish at this point however.
Oh, I also have included some conditional stuff in the code so it will be
compatible in both the 9.X and 10 environments.
Performance has been a focus in recent changes and I believe this revision
driver will perform very well in most workloads.
MFC after: 2 weeks
stops updating the vertical retrace indicator. The text mouse
renderer in syscons is executing from the callout and spins waiting
for the start of next frame. As result, after the X server finishes,
since the VGA cannot be turned on, but syscons does not know about
this, the clock swi spins forever.
Hack around the problem by disabling wait for the retrace if KMS is
activated.
Diagnosed and tested by: Michiel Boland <boland37@xs4all.nl>
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
thread might fault on the same GTT offset meantime and instantiate the
mapping. Recheck that the mgt device object still does not have a
page at the current offset after relocking, and return a possibly
installed page.
Reported by: Oleg Sidorkin <osidorkin@gmail.com>
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
