checksum offloading and VLAN hardware tag insertion/stripping from
the currently enabled hardware offloading capabilities.
Previously if_hwassist, which was initialized to TX/RX checksum
offloading, was blindly used to enable both TX and RX checksum
offloading such that disabling either TX or RX checksum offloading
was not possible.
ti(4) controllers support TX/RX checksum offloading with VLAN
tagging so announce TX/RX checksum offloading capability over VLAN
to vlan(4).
Make VLAN hardware tag insertion/stripping honors currently enabled
interface capability instead of blindly enabling VLAN hardware
tagging. This change allows disabling hardware support of VLAN tag.
Because ti(4) supports VLAN oversized frames, make network stack
know the capability by setting if_hdrlen.
While I'm here, rewrite SIOCSIFCAP handler and make sure to
reinitialize controller whenever TX/RX checksum offloading and VLAN
hardware tagging option is changed. The requirement of controller
reinitialization comes from the limitation of Tigon I/II firmware.
Tigon I/II firmware requires all related RCBs should be
reinitialized whenever any of its hardware offloading capabilities
change.
vlan(4) is also notified whenever the parent interface's capability
changes such that it can correctly handle TX/RX checksum offloading
based on parent interface's enabled offloading capabilities.
RX checksum offloading handler was changed to make upper stack use
controller computed partial checksum value. Previously, ti(4) just
set the computed value for any frames(IPv4, IPv6) and the value was
not used in upper stack because driver didn't set CSUM_DATA_VALID
such that upper network stack had to recompute checksum of TCP/UDP
packets. I have no idea how this was not noticed for a long time.
With this change, upper network stack does not have to fully
recompute the checksum such that calculating pseudo checksum based
on partial checksum is sufficient to know whether received packet's
checksum is correct or not. However, I don't know why ti(4) does
not have controller compute pseudo checksum as controller has
ability to do it. I'm just guessing enabling that feature could
trigger a firmware bug or could be slower than computing it on host
side so just leave it as it was.
In order not to produce false positives, ti(4) now checks whether
controller actually computed IP or TCP/UDP checksum by checking
ti_flags field.
state changes. Hide superfluous link up/down message under
bootverbose since if_link_state_change(9) shows that information.
While I'm here, change baudrate with the resolved speed of the
established link instead of blindly setting it 1G. Unfortunately,
it seems there is no way to differentiate 10/100Mbps from
non-gigabit link so just assume we established a 100Mbps link if
current link is not a gigabit link.
This was broken in r175872.
We have a UMA backed jumbo allocator and that is much better
implementation than having a local jumbo buffer allocator in
driver. This local allocator would be removed in near future but
fixing build before removal wouldn't be a bad idea.
replace amd(4) with the former in the amd64, i386 and pc98 GENERIC kernel
configuration files. Besides duplicating functionality, amd(4), which
previously also supported the AMD Am53C974, unlike esp(4) is no longer
maintained and has accumulated enough bit rot over time to always cause
a panic during boot as long as at least one target is attached to it
(see PR 124667).
PR: 124667
Obtained from: NetBSD (based on)
MFC after: 3 days
corresponding Linux driver uses. This allows mpt(4) to still recognize
all good SATA devices in presence of a defective one, which takes about
45 seconds.
In the long term we probably should implement the logic used by mpt2sas(4)
allowing IOC port initialization to complete at a later time.
Submitted by: Andrew Boyer
MFC after: 3 days
by rman_get_virtual(9) to access device registers sparc64 currently cares
about.
Ideally ata(4) should just be converted to access these using bus_space(9)
read/write functions instead as there's really no reason to do it the
former way. However, this part of ata-siliconimage.c should go away in
favor of siis(4) sooner or later anyway and I don't have the hardware to
actually test the SX4 bits of ata-promise.c.
Also ideally the other architectures should also properly handle the
BUS_SPACE_MAP_LINEAR flag of bus_space_map(9) so this code wouldn't need
to be #ifdef'ed.
take advantage of it instead of duplicating it. This reduces the size of
the i386 GENERIC kernel by about 4k. The only potential in-tree user left
unconverted is xe(4), which generally should be changed to use miibus(4)
instead of implementing PHY handling on its own, as otherwise it makes not
much sense to add a dependency on miibus(4)/mii_bitbang(4) to xe(4) just
for the MII bitbang'ing code. The common MII bitbang'ing code also is
useful in the embedded space for using GPIO pins to implement MII access.
- Based on lessons learnt with dc(4) (see r185750), add bus barriers to the
MII bitbang read and write functions of the other drivers converted in
order to ensure the intended ordering. Given that register access via an
index register as well as register bank/window switching is subject to the
same problem, also add bus barriers to the respective functions of smc(4),
tl(4) and xl(4).
- Sprinkle some const.
Thanks to the following testers:
Andrew Bliznak (nge(4)), nwhitehorn@ (bm(4)), yongari@ (sis(4) and ste(4))
Thanks to Hans-Joerg Sirtl for supplying hardware to test stge(4).
Reviewed by: yongari (subset of drivers)
Obtained from: NetBSD (partially)
- Move esp_devclass to ncr53c9x.c in order to allow different bus front-ends
to use it.
- Use KOBJMETHOD_END.
- Remove the gl_clear_latched_intr hook as it's not needed for any of the
chips nor the front-ends supported in FreeBSD and likely never will be.
- Correct the DMA constraints used in the SBus front-end, the LSI64854 isn't
limited to 32-bit DMA.
- The ESP200 also only supports up to 64k transfers.
- Don't let the DMA and SBus front-end supply a maximum transfer size larger
than MAXPHYS as that's the maximum the upper layers use and we otherwise
just waste resources unnecessarily.
- Initialize the ECB callout and don't zero the handle when returning ECBs
to the free list so that ncr53c9x_callout() actually is called with the
driver lock held.
- On detach the driver lock should be held across cam_sim_free() according
to isp(4) and a panic received.
- Check the return value of NCRDMA_SETUP(), i.e. bus_dmamap_load(9), and try
to handle failures gracefully.
- In ncr53c9x_action() replace N calls to xpt_done() in a switch with just
one at the end.
- On XPT_PATH_INQ report "NCR" rather than "Sun" as the vendor as the former
is somewhat more correct as well as the maximum supported transfer size via
maxio in order to take advantage of controllers that that can handle more
than DFLTPHYS.
- Print the number of MESSAGE (EXTENDED) rejected.
- Fix the path encoded in the multiple inclusion protection of ncr53c9xvar.h.
- Correct the DMA constraints used in the LSI64854 core to not exceed the
maximum supported transfer size and include the boundary so we don't need
to check on every setup of a DMA transfer.
- Let the bus DMA map callbacks do nothing in case of an error.
- Correctly handle > 64k transfers for FAS366 in the LSI64854. A new feature
flag NCR_F_LARGEXFER was introduced so we just need to check for this one
and not for individual controllers supporting large transfers in several
places.
- Let the LSI64854 core load transfer buffers using BUS_DMA_NOWAIT as the
NCR53C9x core can't handle EINPROGRESS. Due to lack of bounce buffers
support, sparc64 doesn't actually use EINPROGRESS and likely never will,
as an example for writing additional front-ends for the NCR53C9x core it
makes sense to set BUS_DMA_NOWAIT anyway though.
- Some minor cleanup.
to an API change in CAM. It's once again possible to link a static kernel
with 'mfi' without requiring 'scbus' as well. Ditto for KLD loading.
Submitted by: kib
Reviewed by: ken
MFC after: 3 days
(mostly with Catalan characters in mind, but it probably
benefits other languages).
The new mappings are as follows:
▮ -> █
ÀÈÍÏÓÒÚ -> AEIIOOU
ŀ / Ŀ -> l / L
Reviewed by: ed
Approved by: kib (mentor)
their length.
Without this, an error frame mbuf would:
* have its size adjusted;
* thrown at the radiotap code;
* then since it's never consumed, the rxbuf/mbuf is then re-added to the
RX descriptor list with the small size;
* .. and the hardware ends up (sometimes) only DMA'ing part of a frame into
the small buffer, chaining RX frames together (setting the more flag).
I discovered this particular issue when doing some promiscuous radiotap
testing; I found that I'd occasionally get rs_more set in RX descriptors
w/ the first frame length being very small (sub-100 bytes.) The driver
handles 2-descriptor RX frames (but not more), so this still worked; it
was just odd.
This is suboptimal and may benefit from being replaced with caching
the m_pkthdr_len and m_len fields, then restoring them after completion.
bge(4) sends BGE_FW_CMD_DRV_ALIVE command to firmware every 2
seconds. BGE_FW_CMD_DRV_ALIVE command requires 4 bytes data. This
data contains timeout value in seconds until the next
BGE_FW_CMD_DRV_ALIVE command.
Broadcom recommends driver set the value 3 times longer than the
interval that it sends BGE_FW_CMD_DRV_ALIVE. Currently bge(4) uses
3 seconds so probably we have to increase it in future and use
different ALIVE command(e.g. BGE_FW_CMD_DRV_ALIVE3).
No functional changes.
This bit(SW event 7 in publicly available data sheet) is used to
make RX CPU handle a firmware command and the bit is automatically
cleared after RX CPU completed the command.
Generally firmware command takes the following steps.
1. Write BGE_SRAM_FW_CMD_MB with a command.
2. Write BGE_SRAM_FW_CMD_LEN_MB with the length of the command in bytes.
3. Write BGE_SRAM_FW_CMD_DATA_MB with actual command data.
4. Generate BGE_RX_CPU_EVENT and let firmware handle the command.
5. Wait for the ACK of the firmware command.
No functional changes.
about the various driver events like load, unload, reset, suspend,
restart, and ioctl operations.
Define driver's event rather than using hard-coded values. We don't
still send suspend/resume event to firmware.
Previously bge(4) used BGE_SDI_STATUS to send events. Because driver
has to access firmware mail box to inform current state, using
BGE_SDI_STATUS register was wrong. The end result was the same as
BGE_SDI_STATUS is 0x0C04.
No functional changes.
The origin of GENCOMM seems to come from Alteon Tigon Host/NIC
interface definition where it defines general communications region
which is active when firmware is loaded and running. This region
was used in communication between the host and processor internal
to the Tigon chip.
Broadcom data sheet also defines the region as 'Software Gencomm'
in NetXtreme memory map but lacks detailed description of its
interface so it was hard to know which ones are used for which
interface.
This change shall slightly enhance readability.
No functional changes.
larger than 4KB in size. However the maximum DMA segment size
created in DMA tag is 4KB, so we wouldn't encounter the issue here.
Just record this issue such that let developers not to create a DMA
segment that is larger than 4KB for BCM5719. It's possible to split
a DMA segment into multiple smaller ones in run time but I believe
it's not worth to implement that.
o Protect bge(4) status block access and register dump with driver lock.
o Add missing bus_dmamap_sync() before dumping status block.
o Use minimum status block size, 32 bytes, for status block dump on most
controllers except BCM5700 AX/BX.
While I'm here, make the handler show 5717 Plus in hardware flags.
