so its available for use in generic scsi code.
This is a pre-requirement for using VPD queries to determine available SCSI
delete methods within scsi_da.
Reviewed by: mav
Approved by: pjd (mentor)
MFC after: 2 weeks
commands to an ATA device attached via a SCSI control.
sys/cam/scsi/scsi_all.c:
- Added scsi_ata_identify, scsi_ata_trim
Which use ATA Pass-Through to send commands to the attached disk.
sys/cam/scsi/scsi_all.h:
- Added defines for all missing ATA Pass-Through commands values.
- Added scsi_ata_identify, scsi_ata_trim methods used in ATA TRIM
support.
- Added scsi_vpd_logical_block_prov structure used when querying for
the supported sizes UNMAP commands.
- Added scsi_vpd_block_limits structure used when querying for the
supported sizes of the UNMAP command.
Reviewed by: mav
Approved by: pjd (mentor)
MFC after: 2 weeks
size of a delete request sent to the providing device performed by g_dev_ioctl.
This allows the kernel and apps via ioctl e.g. newfs -E to request large LBA
deletes which siginificantly improves performance.
Previously this was hard coded to 65536 sectors, the new default is 262144
which doubles the throughput of deletes on commonly available SSD's.
In tests on a Intel 520 120GB FW: 400i disk it improved the delete throughput
from 1.6GB/s to over 2.6GB/s on a full disk delete such as that done via
newfs -E
For some SSD's where delete time is pretty much constant, no matter what
the request, setting this to 0 will provide significantly better throughput
e.g. Samsung 840 240GB FW DXT07B0Q @ 262144 = 79G/s, @ 0 = 2259G/s
Reviewed by: mav
Approved by: pjd (mentor)
MFC after: 2 weeks
I/O clock. Thankfully, the simple executive provies a way to querry
the proper clock that works on all models. Move to asking for the SCLK
via this interface.
This gets the serial console working after we start init and open the
console and set the divisor (which turned the output from good to
bad). I can login on the console now.
and tuned value, we would advertise the unsupported value to CAM and it would
merrily destroy the controller with way too many IO operations.
This manifests itself in a Zero Memory RAID configuration for a P410 and
possibly other controllers.
Obtained from: Yahoo! Inc.
MFC after: 2 weeks
in the pcb. setjmp/longjmp in the kernel also used these values, so
continue to use them although their use isn't technically the pcb
register array (matching is all that's important for setjmp/longjmp in
the kernel). Finally, eliminate the old register names from regnum.h.
This is a lexical change only. The non-debug .o files have the same md5.
same place as dst, or to the sockaddr in the routing table.
The const constraint of gw makes us safe from modifing routing table
accidentially. And "onstantness" of dst allows us to remove several
bandaids, when we switched it back at &ro->ro_dst, now it always
points there.
Reviewed by: rrs
Rework the guest register fetch code to allow the RIP to
be extracted from the VMCS while the kernel decoder is
functioning.
Hit by the OpenBSD local-apic code.
Submitted by: neel
Reviewed by: grehan
Obtained from: NetApp
Merge vendor bugfix for a possible deadlock related to async destroy
and improve write performance by introducing a new lock protecting
tx_open_txg.
Illumos ZFS issues:
3642 dsl_scan_active() should not issue I/O to determine if async
destroying is active
3643 txg_delay should not hold the tc_lock
MFC after: 1 week
route. What it was is there are two places in ip_output.c
where we do a goto again. One place was fine, it
copies out the new address and then resets dst = ro->rt_dst;
But the other place does *not* do that, which means earlier
when we found the gateway, we have dst pointing there
aka dst = ro->rt_gateway is done.. then we do a
goto again.. bam now we clobber the default route.
The fix is just to move the again so we are always
doing dst = &ro->rt_dst; in the again loop.
PR: 174749,157796
MFC after: 1 week
GDT from the correct segment, otherwise a triple fault would be caused.
In some virtual environments (VMware, VirtualBox, etc) this could lead
to a unhandled error or hang in the guest emulation software.
Thanks to avg and jhb for a few hints in the right direction.
Noticed by: Jeremy Chadwick <jdc@koitsu.org> (and many others)
MFC after: 1 week
instead of kernel_map size to prevent kernel memory exhaustion
by mbufs and a subsequent panic on physical page allocation
failure.
On architectures without a direct map all mbuf memory (except
for jumbo mbufs larger than PAGE_SIZE) comes from kmem_map.
It is the limiting factor hence.
For architectures with a direct map using the size of kmem_map
is a good proxy of available kernel memory as well. If it is
much smaller the mbuf limit may be sub-optimal but remains
reasonable, while avoiding panics under exhaustion.
The overall mbuf memory limit calculation may be reconsidered
again later, however due to the many different mbuf sizes and
different backing KVM maps it is a tricky subject.
Found by: pho's new network stress test
Pointed out by: alc (kmem_map instead of kernel_map)
Tested by: pho
duplicate ACK make sure we actually have new data to send.
This prevents us from sending unneccessary pure ACKs.
Reported by: Matt Miller <matt@matthewjmiller.net>
Tested by: Matt Miller <matt@matthewjmiller.net>
MFC after: 2 weeks
impossible to set quota and reservation on pools lower than version 22.
Problem has been reported and a solution discussed with vendor.
Illumos ZFS issues:
3739 cannot set zfs quota or reservation on pool version < 22
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reported by: Steve Wills <swills@FreeBSD.org>
MFC after: 3 days
Partially implement generic_bs_*_8() for MIPS platforms.
This is known to work with TARGET_ARCH=mips64 with FreeBSD/BERI.
Assuming that other definitions in cpufunc.h are correct it will
work on non-o64 ABI systems except sibyte. On sibyte and o32 systems
generic_bs_*_8() will remain panic() implementations.
Sponsored by: DARPA, AFRL
Reviewed by: imp, jmallett (older versions)
