Change 231100 by brooks@brooks_zenith on 2013/07/12 21:01:31
Add a new option ALTERA_SDCARD_FAST_SIM which checks immediatly
for success of I/O operations rather than queuing a task.
MFC after: 3 days
Sponsored by: DARPA/AFRL
Change 227594 by brooks@brooks_zenith on 2013/04/11 17:10:14
When we fail, print the error that occured if we are giving
up or if bootverbose is set.
MFC after: 3 days
Sponsored by: DARPA/AFRL
Add a missing 0 to the mask for byte0 of C_SIZE.
The previous mask (0xc) worked except that the last 0-1536K of the disk
could not be accessed since we were shifting the (wrong) bits we did
mask off the right edge.
Implement an FDT attachment for altera_avgen(4).
Portions of the changeset updating DTS and device.hints will be merged
separately.
Sponsored by: DARPA, AFRL
Rework altera_avgen(4) to cleanly(ish) separate nexus bus
attachment from the driver itself. This should allow us to
plug in an fdt attachment more easily.
Sponsored by: DARPA, AFRL
Start restructuring of altera_avgen(4) so that it can have an FDT
attachment -- this requires first properly breaking out the current
nexus attachment from the driver implementation.
Sponsored by: DARPA, AFRL
which presents a UART-like interface over the Avalon bus that can be
addressed over JTAG. This IP core proves extremely useful, allowing us to
connect trivially to the FreeBSD console over JTAG for FPGA-embedded hard
and soft cores. As interrupts are optionally configured for this soft
core, we support both interrupt-driven and polled modes of operation,
which must be selected using device.hints. UART instances appear in /dev
as ttyu0, ttyu1, etc.
However, it also contains a number of quirks, which make it difficult to
tell when JTAG is connected, and some buffering issues. We work around
these as best we can, using various heuristics.
While the majority of this device driver is not only not BERI-specific,
but also not MIPS-specific, for now add its defines in the BERI files
list, as the console-level parts are aware of where the first JTAG UART
is mapped on Avalon, and contain MIPS-specific address translation, to
use before Newbus and device.hints are available.
Sponsored by: DARPA, AFRL
which can be synthesised in Altera FPGAs. An altera_sdcardc device
probes during the boot, and /dev/altera_sdcard devices come and go as
inserted and removed. The device driver attaches directly to the
Nexus, as is common for system-on-chip device drivers.
This IP core suffers a number of significant limitations, including a
lack of interrupt-driven I/O -- we must implement timer-driven polling,
only CSD 0 cards (up to 2G) are supported, there are serious memory
access issues that require the driver to verify writes to memory-mapped
buffers, undocumented alignment requirements, and erroneous error
returns. The driver must therefore work quite hard, despite a fairly
simple hardware-software interface. The IP core also supports at most
one outstanding I/O at a time, so is not a speed demon.
However, with the above workarounds, and subject to performance
problems, it works quite reliably in practice, and we can use it for
read-write mounts of root file systems, etc.
Sponsored by: DARPA, AFRL
CPU cores on Altera FPGAs. The device driver allows memory-mapped devices
on Altera's Avalon SoC bus to be exported to userspace via device nodes.
device.hints directories dictate device name, permissible access methods,
physical address and length, and I/O alignment. Devices can be accessed
using read(2)/write(2), but also memory mapped in userspace using mmap(2).
Devices attach directly to the Nexus, as is common for embedded device
drivers; in the future something more mature might be desirable. There is
currently no facility to support directing device-originated interrupts to
userspace.
In the future, this device driver may be renamed to socgen(4), as it can
in principle also be used with other system-on-chip (SoC) busses, such as
Axi on ASICs and FPGAs. However, we have only tested it on Avalon busses
with memory-mapped ROMs, frame buffers, etc.
Sponsored by: DARPA, AFRL
